M. A. I. Schutyser
M. A. I. Schutyser has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
A. Rinzema
Wageningen Centre for Food Sciences, P.O. Box 557, 6700 AN Wageningen, The Netherlands; telephone: 31‐317‐484372; fax: 31‐317‐482237
3 shared publicationsF. J. Weber
Wageningen Centre for Food Sciences, P.O. Box 557, 6700 AN Wageningen, The Netherlands; telephone: 31‐317‐484372; fax: 31‐317‐482237
3 shared publicationsW. J. Briels
Computational Dispersion Rheology, University of Twente, Enschede, The Netherlands
3 shared publicationsR. M. Boom
Wageningen University Food and Bioprocess Engineering Group, Wageningen, The Netherlands
2 shared publicationsJ. T. Padding
University of Twente, Computational Dispersion Rheology, PO Box 217, 7500 AE Enschede, The Netherlands
1 shared publicationP. de Pagter
Wageningen University Food and Bioprocess Engineering Group, Wageningen, The Netherlands
1 shared publication
Latest Publications
- 20 June 2003
- Published by Wiley in Biotechnology and Bioengineering
- Vol. 83 (5) , 503-513
Substrate aggregation due to aerial hyphae during discontinuously mixed solid‐state fermentation with Aspergillus oryzae: Experiments and modeling
Solid‐state fermentation (SSF) is prone to process failure due to channeling caused by evaporative cooling and the formation of an interparticle mycelium network. Mixing is needed to break the mycelium network and to avoid such failure. This study presents the first attempt to quantify and predict the effect of mycelium bonds on particle mixing and vice versa. We developed a novel experimental set‐up to measure the tensile strength of hyphal bonds in SSF: Aspergillus oryzae was cultivated between two wheat‐dough disks and the tensile strength of the aerial mycelium was measured with a texture analyzer. Tensile strength at different incubation times was related to oxygen consumption, to allow a translation to a rotating drum with A. oryzae cultivated on wheat grain. We performed several discontinuously mixed solid‐state fermentations in the drum fermentor and measured the number and size of grain‐aggregates remaining after the first mixing action. We integrated data on mycelium tensile strength into a previously developed two‐dimensional discrete‐particle model that calculates forces acting on individual substrate particles and the resulting radial‐particle movements. The discrete‐particle model predicted the quantity and size of the aggregates remaining after mixing successfully. The results show that the first mixing event in SSF with A. oryzae is needed to break mycelium to avoid aggregate formation in the grain bed, and not to distribute water added to compensate for evaporation losses, or smooth out temperature gradients. © 2003 Wiley Periodicals, Inc. Biotechnol Bioeng 83: 503–513, 2003.
- 20 June 2003
- Published by Wiley in Biotechnology and Bioengineering
- Vol. 83 (5) , 503-513
Substrate aggregation due to aerial hyphae during discontinuously mixed solid‐state fermentation with Aspergillus oryzae: Experiments and modeling
Solid‐state fermentation (SSF) is prone to process failure due to channeling caused by evaporative cooling and the formation of an interparticle mycelium network. Mixing is needed to break the mycelium network and to avoid such failure. This study presents the first attempt to quantify and predict the effect of mycelium bonds on particle mixing and vice versa. We developed a novel experimental set‐up to measure the tensile strength of hyphal bonds in SSF: Aspergillus oryzae was cultivated between two wheat‐dough disks and the tensile strength of the aerial mycelium was measured with a texture analyzer. Tensile strength at different incubation times was related to oxygen consumption, to allow a translation to a rotating drum with A. oryzae cultivated on wheat grain. We performed several discontinuously mixed solid‐state fermentations in the drum fermentor and measured the number and size of grain‐aggregates remaining after the first mixing action. We integrated data on mycelium tensile strength into a previously developed two‐dimensional discrete‐particle model that calculates forces acting on individual substrate particles and the resulting radial‐particle movements. The discrete‐particle model predicted the quantity and size of the aggregates remaining after mixing successfully. The results show that the first mixing event in SSF with A. oryzae is needed to break mycelium to avoid aggregate formation in the grain bed, and not to distribute water added to compensate for evaporation losses, or smooth out temperature gradients. © 2003 Wiley Periodicals, Inc. Biotechnol Bioeng 83: 503–513, 2003.
- 6 June 2002
- Published by Wiley in Biotechnology and Bioengineering
- Vol. 79 (3) , 284-294
Three‐dimensional simulation of grain mixing in three different rotating drum designs for solid‐state fermentation
A previously published two‐dimensional discrete particle simulation model for radial mixing behavior of various slowly rotating drums for solid‐state fermentation (SSF) has been extended to a three‐dimensional model that also predicts axial mixing. Radial and axial mixing characteristics were predicted for three different drum designs: (1) without baffles; (2) with straight baffles; and (3) with curved baffles. The axial mixing behavior was studied experimentally with video‐ and image‐analysis techniques. In the drum without baffles and with curved baffles the predicted mixing behavior matched the observed behavior adequately. The predicted axial mixing behavior in the drum with straight baffles was predicted less accurately, and it appeared to be strongly dependent on particle rotation, which was in contrast to the other drum designs. In the drum with curved baffles complete mixing in the radial and axial direction was achieved much faster than in the other designs; that is, it was already achieved after three to four rotations. This drum design may therefore be very well suited to SSF. It is concluded that discrete particle simulations provide valuable detailed knowledge about particle transport processes, and this may help to understand and optimize related heat and mass transfer processes in SSF. © 2002 Wiley Periodicals, Inc. Biotechnol Bioeng 79: 284–294, 2002.
- 6 June 2002
- Published by Wiley in Biotechnology and Bioengineering
- Vol. 79 (3) , 284-294
Three‐dimensional simulation of grain mixing in three different rotating drum designs for solid‐state fermentation
A previously published two‐dimensional discrete particle simulation model for radial mixing behavior of various slowly rotating drums for solid‐state fermentation (SSF) has been extended to a three‐dimensional model that also predicts axial mixing. Radial and axial mixing characteristics were predicted for three different drum designs: (1) without baffles; (2) with straight baffles; and (3) with curved baffles. The axial mixing behavior was studied experimentally with video‐ and image‐analysis techniques. In the drum without baffles and with curved baffles the predicted mixing behavior matched the observed behavior adequately. The predicted axial mixing behavior in the drum with straight baffles was predicted less accurately, and it appeared to be strongly dependent on particle rotation, which was in contrast to the other drum designs. In the drum with curved baffles complete mixing in the radial and axial direction was achieved much faster than in the other designs; that is, it was already achieved after three to four rotations. This drum design may therefore be very well suited to SSF. It is concluded that discrete particle simulations provide valuable detailed knowledge about particle transport processes, and this may help to understand and optimize related heat and mass transfer processes in SSF. © 2002 Wiley Periodicals, Inc. Biotechnol Bioeng 79: 284–294, 2002.
- 13 November 2001
- Published by Wiley in Biotechnology and Bioengineering
- Vol. 75 (6) , 666-675
Discrete particle simulations predicting mixing behavior of solid substrate particles in a rotating drum fermenter
A soft‐sphere discrete particle model was used to simulate mixing behavior of solid substrate particles in a slow rotating drum for solid‐state fermentation. In this approach, forces acting on and subsequent motion of individual particles can be predicted. The (2D) simulations were qualitatively and quantitatively validated by mixing experiments using video and image analysis techniques. It was found that the simulations successfully predicted the mixing progress as a function of the degree of filling and size of the drum. It is shown that only relatively large, straight baffles perpendicular to the drum wall (67% of the drum radius) increase the mixing performance of the rotating drum. Considering the different aspects of mixing dealt with in this work, it is concluded that the soft sphere discrete particle model can serve as a valuable tool for investigating mixing of solid substrate particles. Finally, it is expected that this model may evolve into a potential tool for design and scale‐up of mixed solid‐state fermenters. © 2001 John Wiley & Sons, Inc. Biotechnol Bioeng 75: 666–675, 2001.
- 13 November 2001
- Published by Wiley in Biotechnology and Bioengineering
- Vol. 75 (6) , 666-675
Discrete particle simulations predicting mixing behavior of solid substrate particles in a rotating drum fermenter
A soft‐sphere discrete particle model was used to simulate mixing behavior of solid substrate particles in a slow rotating drum for solid‐state fermentation. In this approach, forces acting on and subsequent motion of individual particles can be predicted. The (2D) simulations were qualitatively and quantitatively validated by mixing experiments using video and image analysis techniques. It was found that the simulations successfully predicted the mixing progress as a function of the degree of filling and size of the drum. It is shown that only relatively large, straight baffles perpendicular to the drum wall (67% of the drum radius) increase the mixing performance of the rotating drum. Considering the different aspects of mixing dealt with in this work, it is concluded that the soft sphere discrete particle model can serve as a valuable tool for investigating mixing of solid substrate particles. Finally, it is expected that this model may evolve into a potential tool for design and scale‐up of mixed solid‐state fermenters. © 2001 John Wiley & Sons, Inc. Biotechnol Bioeng 75: 666–675, 2001.