Chang Min Chun
Research Subjects
Research Interests
Chang Min Chun has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
T. A. Ramanarayanan
Frick Chemistry Laboratory Princeton University Princeton New Jersey 08544 (USA)
5 shared publicationsFrank Hershkowitz
ExxonMobil Corporate Strategic Research; Annandale New Jersey 08801
4 shared publicationsSanket Desai
ExxonMobil Corporate Strategic Research; Annandale New Jersey 08801
4 shared publicationsTrikur A. Ramanarayanan
Princeton University
3 shared publicationsS. Desai
ExxonMobil Corporate Strategic Research Annandale New Jersey 08801 (USA)
2 shared publications- Trikur A. Ramanarayanan
Frick Laboratory, Department of Chemistry, Princeton University, Princeton, NJ 08544–1009, USA
2 shared publications
Latest Publications
- 16 May 2013
- Published by Wiley in Materials and Corrosion
- Vol. 65 (3) , 282-295
Materials challenges in cyclic carburizing and oxidizing environments for petrochemical applications
Steam cracking is a petrochemical process that cleaves a broad range of hydrocarbon feed molecules into a variety of light olefinic products, including the highly desirable ethylene. Over the course of a cracking operation using a feed mixture of a saturated hydrocarbon and steam around 900–1000 °C in tubular alloy coils located in fired heaters, coke inevitably forms on the inside surfaces of the furnace tubes and must be burned off and/or spalled off periodically using steam or a steam–air mixture. Furnace tube materials are predominantly based on chromia‐forming alloys; such alloys can degrade by carburization and oxide–carbide conversion in such a mixed carburizing–oxidizing environment. These hurdles have been largely overcome by using an alumina‐forming material that provides superior corrosion and coking resistance. Cracking hydrocarbons at much higher temperatures results in high selectivity to acetylene, which can be converted into many petrochemical products including ethylene. The desired hydropyrolysis reaction from hydrocarbons to acetylene can be realized in a reverse‐flow reactor operating above 1500 °C in a scaleable manner. The reactor elements include ceramic components that are placed in the hottest regions of the reactor, and must withstand temperatures in the range of 1500–2000 °C. Moreover, the materials in the hot zone are exposed alternately to a regeneration (heat addition) step that is mildly oxidizing and a pyrolysis (cracking) step that is strongly reducing with a correspondingly high carbon activity. This paper addresses the thermodynamic stability of selected ceramic materials based on alumina, zirconia, and yttria for such an application. Results from laboratory tests involving the exposure of these ceramic materials to simulated process conditions followed by their microstructural characterization are compared with expectations from thermodynamic predictions.
- 16 May 2013
- Published by Wiley in Materials and Corrosion
- Vol. 65 (3) , 282-295
Materials challenges in cyclic carburizing and oxidizing environments for petrochemical applications
Steam cracking is a petrochemical process that cleaves a broad range of hydrocarbon feed molecules into a variety of light olefinic products, including the highly desirable ethylene. Over the course of a cracking operation using a feed mixture of a saturated hydrocarbon and steam around 900–1000 °C in tubular alloy coils located in fired heaters, coke inevitably forms on the inside surfaces of the furnace tubes and must be burned off and/or spalled off periodically using steam or a steam–air mixture. Furnace tube materials are predominantly based on chromia‐forming alloys; such alloys can degrade by carburization and oxide–carbide conversion in such a mixed carburizing–oxidizing environment. These hurdles have been largely overcome by using an alumina‐forming material that provides superior corrosion and coking resistance. Cracking hydrocarbons at much higher temperatures results in high selectivity to acetylene, which can be converted into many petrochemical products including ethylene. The desired hydropyrolysis reaction from hydrocarbons to acetylene can be realized in a reverse‐flow reactor operating above 1500 °C in a scaleable manner. The reactor elements include ceramic components that are placed in the hottest regions of the reactor, and must withstand temperatures in the range of 1500–2000 °C. Moreover, the materials in the hot zone are exposed alternately to a regeneration (heat addition) step that is mildly oxidizing and a pyrolysis (cracking) step that is strongly reducing with a correspondingly high carbon activity. This paper addresses the thermodynamic stability of selected ceramic materials based on alumina, zirconia, and yttria for such an application. Results from laboratory tests involving the exposure of these ceramic materials to simulated process conditions followed by their microstructural characterization are compared with expectations from thermodynamic predictions.
- 12 February 2013
- Published by Springer Nature in Journal of Materials Science
- Vol. 48 (11) , 3975-3984
Degradation of zirconate materials in ultra-high temperature reverse-flow pyrolysis reactors
- 12 February 2013
- Published by Springer Nature in Journal of Materials Science
- Vol. 48 (11) , 3975-3984
Degradation of zirconate materials in ultra-high temperature reverse-flow pyrolysis reactors
- 24 October 2012
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 95 (12) , 3962-3970
Ceramic Dusting Corrosion of Yttria‐Stabilized Zirconia in Ultra High Temperature Reverse‐Flow Pyrolysis Reactors
A reverse‐flow reactor enables the pyrolysis of hydrocarbons, at temperatures ranging from 1500°C to 2000°C, to high‐value petrochemical products through acetylene intermediate. Materials in the hottest regions of the reactor, exposed to such extreme temperatures, are subject to oxidative cycling over a period of several seconds between a regeneration (heat addition) step that is mildly oxidizing and a pyrolysis (cracking) step that is strongly reducing, accompanied by high carbon activity. Experimental results obtained from single crystal and polycrystalline yttria‐stabilized zirconia ( YSZ ) ceramics of different porosities show that the pyrolysis reaction triggers the carburization of YSZ by diffusion of carbon through the lattice, the grain boundaries, and the pores. Subsequently graphite deposition occurs on the carburized surface. During the regeneration step, some of the graphite and (oxy)carbide are reoxidized. Corrosion advances in subsequent cycles by a repetition of oxide‐carbide interconversion, carbon precipitation, and reoxidation steps. Since degradation involves the breakup of the bulk ceramic structure into powder or “dust” and is reminiscent of metal dusting corrosion observed in metallic materials in carbon‐supersaturated environments, we name this corrosion “ceramic dusting.” Details of the corrosion mechanism and the steps leading to such degradation are discussed.
- 24 October 2012
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 95 (12) , 3962-3970
Ceramic Dusting Corrosion of Yttria‐Stabilized Zirconia in Ultra High Temperature Reverse‐Flow Pyrolysis Reactors
A reverse‐flow reactor enables the pyrolysis of hydrocarbons, at temperatures ranging from 1500°C to 2000°C, to high‐value petrochemical products through acetylene intermediate. Materials in the hottest regions of the reactor, exposed to such extreme temperatures, are subject to oxidative cycling over a period of several seconds between a regeneration (heat addition) step that is mildly oxidizing and a pyrolysis (cracking) step that is strongly reducing, accompanied by high carbon activity. Experimental results obtained from single crystal and polycrystalline yttria‐stabilized zirconia ( YSZ ) ceramics of different porosities show that the pyrolysis reaction triggers the carburization of YSZ by diffusion of carbon through the lattice, the grain boundaries, and the pores. Subsequently graphite deposition occurs on the carburized surface. During the regeneration step, some of the graphite and (oxy)carbide are reoxidized. Corrosion advances in subsequent cycles by a repetition of oxide‐carbide interconversion, carbon precipitation, and reoxidation steps. Since degradation involves the breakup of the bulk ceramic structure into powder or “dust” and is reminiscent of metal dusting corrosion observed in metallic materials in carbon‐supersaturated environments, we name this corrosion “ceramic dusting.” Details of the corrosion mechanism and the steps leading to such degradation are discussed.
- 15 October 2012
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 11 (1) , 106-117
Materials Challenges in Reverse‐Flow Pyrolysis Reactors for Petrochemical Applications
- 15 October 2012
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 11 (1) , 106-117
Materials Challenges in Reverse‐Flow Pyrolysis Reactors for Petrochemical Applications
- 1 June 2012
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 68 (9) , 810-821
Metal Dusting Resistant Copper-Based Materials
Cu and Cu-based alloy coatings suppress carbon transfer to the metal surface from carbon-supersaturated gaseous environments. The metal dusting resistance of such coatings has been investigated in CO-H2 gas mixtures at temperatures ranging from 450°C to 700°C. Conventional plating and cladding methods have been used to deposit Cu-based materials on the surfaces of commercial materials such as 2.25Cr-0.5Mo steel and carbon steel. In addition to the performance of Cu-based materials under laboratory conditions, the effect of alloying elements such as Sn, Zn, Ni, Si, and Al in Cu on the corrosion process and the coating/substrate interface stability are discussed with particular attention to commercial scale applications.
- 1 June 2012
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 68 (9) , 810-821
Metal Dusting Resistant Copper-Based Materials
Cu and Cu-based alloy coatings suppress carbon transfer to the metal surface from carbon-supersaturated gaseous environments. The metal dusting resistance of such coatings has been investigated in CO-H2 gas mixtures at temperatures ranging from 450°C to 700°C. Conventional plating and cladding methods have been used to deposit Cu-based materials on the surfaces of commercial materials such as 2.25Cr-0.5Mo steel and carbon steel. In addition to the performance of Cu-based materials under laboratory conditions, the effect of alloying elements such as Sn, Zn, Ni, Si, and Al in Cu on the corrosion process and the coating/substrate interface stability are discussed with particular attention to commercial scale applications.
- 31 October 2008
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 5 (6) , 597-609
Erosion–Corrosion‐Resistant Titanium Diboride Cermets for High‐Temperature Process Applications
Reactor vessels and internals used for high‐temperature processes such as in refining and chemical industries are exposed to aggressive fluids often containing hard catalyst particles moving at high velocities. The protection of these vessels and internals against erosion‐ and corrosion‐induced material degradation is a technological challenge. The life span of the state–of‐the‐art monolithic refractory liners currently in use is limited by excessive mechanical attrition of the liner from high‐velocity solid particle impingement, mechanical cracking, and spalling. The advanced TiB 2 ‐stainless‐steel (SS) cermets are designed for chemical stability required for long‐term service and offer an order of magnitude higher erosion resistance over the state‐of‐the‐art, high fracture toughness ( K 1 C ∼12 MPa m 1/2 ) and excellent corrosion resistance ( k p ∼1.9 × 10 −11 g 2 /cm 4 /s at 800°C in air). Materials, design, microstructure, key mechanical properties, erosion, and corrosion resistance of the newly developed TiB 2 ‐SS cermets are presented.
- 31 October 2008
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 5 (6) , 597-609
Erosion–Corrosion‐Resistant Titanium Diboride Cermets for High‐Temperature Process Applications
Reactor vessels and internals used for high‐temperature processes such as in refining and chemical industries are exposed to aggressive fluids often containing hard catalyst particles moving at high velocities. The protection of these vessels and internals against erosion‐ and corrosion‐induced material degradation is a technological challenge. The life span of the state–of‐the‐art monolithic refractory liners currently in use is limited by excessive mechanical attrition of the liner from high‐velocity solid particle impingement, mechanical cracking, and spalling. The advanced TiB 2 ‐stainless‐steel (SS) cermets are designed for chemical stability required for long‐term service and offer an order of magnitude higher erosion resistance over the state‐of‐the‐art, high fracture toughness ( K 1 C ∼12 MPa m 1/2 ) and excellent corrosion resistance ( k p ∼1.9 × 10 −11 g 2 /cm 4 /s at 800°C in air). Materials, design, microstructure, key mechanical properties, erosion, and corrosion resistance of the newly developed TiB 2 ‐SS cermets are presented.
- 1 January 2008
- Published by Elsevier
Contributor contact details
- 7 March 2007
- Published by Springer Nature in Oxidation of Metals
- Vol. 67 (3-4) , 215-234
Corrosion Resistance of a High-Silicon Alloy in Metal-Dusting Environments
- 7 March 2007
- Published by Springer Nature in Oxidation of Metals
- Vol. 67 (3-4) , 215-234
Corrosion Resistance of a High-Silicon Alloy in Metal-Dusting Environments
- 1 January 2007
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 154 (5) , C231-C240
Metal Dusting Corrosion of Nickel-Based Alloys
Metal dusting corrosion of nickel-based alloys (i.e., Inconel 600, 601, and 693) has been simulated in high-carbon-activity environments over a temperature range of 450–750°C450–750°C . Overall, Ni-based alloys corrode by a combination of carbon diffusion and precipitation in the alloy interior and atom migration through surface carbon deposits. The formation of protective surface oxide films provides initial protection against metal dusting, but local rupture of surface Cr-rich oxide films allows rapid carbon diffusion into the alloy. The focus of this research was to advance the understanding of the corrosion mechanisms of Ni-based alloys by characterizing interfacial processes at the nanometer level. In addition to the effect of temperature and environmental chemistry, the mechanistic aspects of metal dusting are discussed with particular attention to the stages of microstructure evolution as degradation proceeds.
- 1 January 2007
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 154 (5) , C231-C240
Metal Dusting Corrosion of Nickel-Based Alloys
Metal dusting corrosion of nickel-based alloys (i.e., Inconel 600, 601, and 693) has been simulated in high-carbon-activity environments over a temperature range of 450–750°C450–750°C . Overall, Ni-based alloys corrode by a combination of carbon diffusion and precipitation in the alloy interior and atom migration through surface carbon deposits. The formation of protective surface oxide films provides initial protection against metal dusting, but local rupture of surface Cr-rich oxide films allows rapid carbon diffusion into the alloy. The focus of this research was to advance the understanding of the corrosion mechanisms of Ni-based alloys by characterizing interfacial processes at the nanometer level. In addition to the effect of temperature and environmental chemistry, the mechanistic aspects of metal dusting are discussed with particular attention to the stages of microstructure evolution as degradation proceeds.