J. R. M. D'ALmeida
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
J. R. M. D'ALmeida has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Bluma Guenther Soares
Department of Metallurgical and Materials Engineering Federal University of Rio de Janeiro (UFRJ) Rio de Janeiro Brazil
1 shared publication L. C. M. Miranda
Laboratório Associado de Sensores e Materiais, Instituto Nacional de Pesquisas Espaciais, 12201-970, São José dos Campos, SP, Brazil
1 shared publicationL. H. de Carvalho
Materials Department, Universidade Federal de Campina Grande, Av. Aprígio Veloso, 882 Bodocongó 58109–970, Campina Grande, PB, Brazil
1 shared publicationN. G. Berry
Centro de Pesquisa e Desenvolvimento Leopoldo Américo M. de Mello (CENPES), Petrobras , Cidade Universitária , Rio de Janeiro, RJ, Brazil ; Departamento de Ciência dos Materiais e Metalurgia , Pontifícia Universidade Católica, do Rio de Janeiro , Rio de Janeiro, RJ, Brazil
1 shared publication- Norberto Cella
Instituto Politécnico, IPRJ Universidade do Estado do Rio de Janeiro, UERJ Nova Friburgo RJ Brazil
1 shared publication S. N. Monteiro
Centro de Ciência e Tecnologia, Universidade Estadual do Norte Fluminense, 28015-820 Campos, RJ, Brazil
1 shared publication
Latest Publications
- 3 December 2007
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 83 (12) , 1031-1042
Variation of the Adhesive Properties of an Epoxy Resin Modified by End-Functionalized Liquid Polybutadiene as a Function of Temperature and Water Absorption
The adhesive behavior of a diglycidyl ether of bisphenol-A epoxy resin modified by end-functionalyzed liquid polybutadiene was evaluated as a function of the temperature and of the time of immersion in distilled water. The neat epoxy and three modified systems were analyzed. Butt joints and single-lap joints were tested using an API X60 steel as substrate. The monophasic system obtained by reacting the epoxy monomer with hydroxyl-terminated polybutadiene (HTPB) functionalyzed with isocyanate groups (EPI) showed the best performance. The results show that this system is stable in respect to water degradation, but changes when exposed to temperature. Under the set of experimental parameters of time and temperature used, however, the adhesive strength increased with the temperature. For all epoxy formulations analyzed the fracture mode observed was of the adhesive type.
- 3 December 2007
- Published by Taylor & Francis in The Journal of Adhesion
- Vol. 83 (12) , 1031-1042
Variation of the Adhesive Properties of an Epoxy Resin Modified by End-Functionalized Liquid Polybutadiene as a Function of Temperature and Water Absorption
The adhesive behavior of a diglycidyl ether of bisphenol-A epoxy resin modified by end-functionalyzed liquid polybutadiene was evaluated as a function of the temperature and of the time of immersion in distilled water. The neat epoxy and three modified systems were analyzed. Butt joints and single-lap joints were tested using an API X60 steel as substrate. The monophasic system obtained by reacting the epoxy monomer with hydroxyl-terminated polybutadiene (HTPB) functionalyzed with isocyanate groups (EPI) showed the best performance. The results show that this system is stable in respect to water degradation, but changes when exposed to temperature. Under the set of experimental parameters of time and temperature used, however, the adhesive strength increased with the temperature. For all epoxy formulations analyzed the fracture mode observed was of the adhesive type.
- 31 August 2004
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 94 (3) , 1209-1217
Evaluation of the mechanical properties of sisal–polyester composites as a function of the polyester matrix formulation
In this work a comparative study on the impact and tensile properties of polyester/sisal fiber reinforced composites was undertaken. The polyester matrix was used bare and modified with: (1) a silane coupling agent; (2) a flame retardant system; and (3) a blend of the silane agent and the flame retardant system. The experimental results show that the flame retardant acts as a particulate reinforcement to the polyester matrix and the silane coupling agent acts as a plasticizer. The simultaneous addition of these two compounds to the polyester resin tended to decrease the performance of the composites. The results obtained show that strength or toughness could be tailored, and although none of the composites manufactured with the modified polyester matrices showed a significant improvement on the fiber–matrix interface strength, a better compromise between impact and tensile properties was obtained with the silane modified matrix. The critical fiber volume fraction was also evaluated and shown to be less than 10% for the sisal–polyester composite investigated here. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1209–1217, 2004
- 31 August 2004
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 94 (3) , 1209-1217
Evaluation of the mechanical properties of sisal–polyester composites as a function of the polyester matrix formulation
In this work a comparative study on the impact and tensile properties of polyester/sisal fiber reinforced composites was undertaken. The polyester matrix was used bare and modified with: (1) a silane coupling agent; (2) a flame retardant system; and (3) a blend of the silane agent and the flame retardant system. The experimental results show that the flame retardant acts as a particulate reinforcement to the polyester matrix and the silane coupling agent acts as a plasticizer. The simultaneous addition of these two compounds to the polyester resin tended to decrease the performance of the composites. The results obtained show that strength or toughness could be tailored, and although none of the composites manufactured with the modified polyester matrices showed a significant improvement on the fiber–matrix interface strength, a better compromise between impact and tensile properties was obtained with the silane modified matrix. The critical fiber volume fraction was also evaluated and shown to be less than 10% for the sisal–polyester composite investigated here. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1209–1217, 2004
- 15 August 1998
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 69 (7) , 1335-1341
Thermal diffusivity of an epoxy system as a function of the hardener content
- 15 August 1998
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 69 (7) , 1335-1341
Thermal diffusivity of an epoxy system as a function of the hardener content