Andrzej Kowalewicz
Research Subjects
Latest Publications
- 26 September 2007
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 179 (11) , 2415-2435
PERFORMANCE, EMISSIONS AND COMBUSTION PARAMETERS OF ECO-DIESEL FUELLED WITH RME AND ETHANOL
Compression ignition (C.I.) engine fuelled with rapeseed oil methyl ester (RME) as the main fuel and bioethanol injected into the inlet port for supporting burning of RME was developed and investigated. The concept of ethanol injection depends on the thesis, that after ignition from burning RME droplets, ethanol-air mixture burns very quickly and promotes combustion of the main fuel droplets, resulting in a shorter combustion period. Experiments carried out with the use of a one-cylinder direct injection diesel engine adapted to ethanol injection enabled to appreciate the influence of ethanol energy fraction on performance, emission and combustion parameters. Significant decrease of CO2 and smoke level was obtained in whole range of load and—also CO and HC emission, while for low load only—NOx emission. The higher the fraction of ethanol, the longer the ignition delay but the shorter the overall time of combustion.
- 26 September 2007
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 179 (11) , 2415-2435
PERFORMANCE, EMISSIONS AND COMBUSTION PARAMETERS OF ECO-DIESEL FUELLED WITH RME AND ETHANOL
Compression ignition (C.I.) engine fuelled with rapeseed oil methyl ester (RME) as the main fuel and bioethanol injected into the inlet port for supporting burning of RME was developed and investigated. The concept of ethanol injection depends on the thesis, that after ignition from burning RME droplets, ethanol-air mixture burns very quickly and promotes combustion of the main fuel droplets, resulting in a shorter combustion period. Experiments carried out with the use of a one-cylinder direct injection diesel engine adapted to ethanol injection enabled to appreciate the influence of ethanol energy fraction on performance, emission and combustion parameters. Significant decrease of CO2 and smoke level was obtained in whole range of load and—also CO and HC emission, while for low load only—NOx emission. The higher the fraction of ethanol, the longer the ignition delay but the shorter the overall time of combustion.
- 1 September 2006
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 220 (9) , 1275-1282
Eco-Diesel Engine Fuelled with Rapeseed Oil Methyl Ester and Ethanol. Part 2: Comparison of Emissions and Efficiency for Two Base Fuels: Diesel Fuel and Ester
A comparison has been made of the efficiency and emissions from a single-cylinder naturally aspirated direct injection compression ignition engine when fuelled either with diesel fuel (DF) or rapeseed oil methyl ester (RME) and additionally with ethanol in different proportions injected into the inlet port during the suction stroke. Investigations were performed at two constant loads, high and low. At each load the proportions of ethanol and base fuel were changed in such a way that the load was held constant. At each load the engine operated at a constant speed and for three injection timings. The obtained results were similar for both fuels, but in the case of RME there were lower carbon dioxide and smoke emissions and in some operating conditions NO x emission was observed. The aim of the ethanol injection, which was produced with air premixed with a homogeneous mixture in the cylinder, was to promote and accelerate combustion of DF/RME droplets, resulting in shorter combustion of the total fuel. The second objective of ethanol addition was to decrease the emissions of smoke and carbon dioxide, because as ethanol burns its combustion products have more H2 O and less CO2. The aim was to provide a sufficient effective energetic fraction of ethanol in order to reach a satisfactory decrease in emissions, which was found to be about 25 per cent for RME and about 20 per cent for diesel fuel.
- 1 September 2006
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 220 (9) , 1275-1282
Eco-Diesel Engine Fuelled with Rapeseed Oil Methyl Ester and Ethanol. Part 2: Comparison of Emissions and Efficiency for Two Base Fuels: Diesel Fuel and Ester
A comparison has been made of the efficiency and emissions from a single-cylinder naturally aspirated direct injection compression ignition engine when fuelled either with diesel fuel (DF) or rapeseed oil methyl ester (RME) and additionally with ethanol in different proportions injected into the inlet port during the suction stroke. Investigations were performed at two constant loads, high and low. At each load the proportions of ethanol and base fuel were changed in such a way that the load was held constant. At each load the engine operated at a constant speed and for three injection timings. The obtained results were similar for both fuels, but in the case of RME there were lower carbon dioxide and smoke emissions and in some operating conditions NO x emission was observed. The aim of the ethanol injection, which was produced with air premixed with a homogeneous mixture in the cylinder, was to promote and accelerate combustion of DF/RME droplets, resulting in shorter combustion of the total fuel. The second objective of ethanol addition was to decrease the emissions of smoke and carbon dioxide, because as ethanol burns its combustion products have more H2 O and less CO2. The aim was to provide a sufficient effective energetic fraction of ethanol in order to reach a satisfactory decrease in emissions, which was found to be about 25 per cent for RME and about 20 per cent for diesel fuel.
- 1 September 2006
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 220 (9) , 1283-1291
Eco-Diesel Engine Fuelled with Rapeseed Oil Methyl Ester and Ethanol. Part 3: Combustion Processes
In Part 1 of the paper efficiency and emissions of the engine fuelled with rape oil methyl ester (RME) and ethanol were presented and discussed. In the second part of the paper a comparison of emissions and brake fuel conversion efficiency of the engine for two base fuels, diesel fuel and rape oil ethyl ester, was carried out. In this paper, Part 3, combustion processes are investigated. Experiments were carried out on the same single-cylinder direct injection compression ignition engine as in Part 1. In the course of the experiments the pressure-time history of the engine cylinder and instantaneous parameters of injection of the RME fuel were measured and used to calculate the rate of heat release and the fraction of fuel burnt versus crank angle, which showed that the higher the energy fraction of ethanol in the total fuel, the longer the ignition delay but the shorter the total time of combustion. It was found that shorter combustion results in higher efficiency.
- 1 September 2006
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 220 (9) , 1283-1291
Eco-Diesel Engine Fuelled with Rapeseed Oil Methyl Ester and Ethanol. Part 3: Combustion Processes
In Part 1 of the paper efficiency and emissions of the engine fuelled with rape oil methyl ester (RME) and ethanol were presented and discussed. In the second part of the paper a comparison of emissions and brake fuel conversion efficiency of the engine for two base fuels, diesel fuel and rape oil ethyl ester, was carried out. In this paper, Part 3, combustion processes are investigated. Experiments were carried out on the same single-cylinder direct injection compression ignition engine as in Part 1. In the course of the experiments the pressure-time history of the engine cylinder and instantaneous parameters of injection of the RME fuel were measured and used to calculate the rate of heat release and the fraction of fuel burnt versus crank angle, which showed that the higher the energy fraction of ethanol in the total fuel, the longer the ignition delay but the shorter the total time of combustion. It was found that shorter combustion results in higher efficiency.