Nick Glumac
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nick Glumac has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
Herman Krier
Mechanical Science and Engineering Department, University of Illinois, Urbana-Champaign, IL, USA
6 shared publications- Patrick T. Lynch
Department of Mechanical & Industrial Engineering University of Illinois at Chicago 842 W Taylor Street Chicago IL-60607 USA
3 shared publications - Adam Hammond-Clements
Sandia National Laboratories, Engineering Sciences Center, Albuquerque, USA
2 shared publications - Colton Willhardt
Department of Mechanical Science and Engineering, University of Illinois at Urbana-Champaign, Urbana, USA
2 shared publications - Emily N. Weerakkody
Lawrence Livermore National Laboratory
2 shared publications - Kyle A. Daniel
Sandia National Laboratories, Engineering Sciences Center, Albuquerque, USA
2 shared publications
Latest Publications
- Open Access
- 1 December 2025
- Published by Office of Scientific and Technical Information (OSTI)
Explosive Soot Challenge (Final Report)
Final report for the GS Soot LDRD FY23-FY25
- 1 December 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessExplosive Soot Challenge (Final Report)
Final report for the GS Soot LDRD FY23-FY25
- Open Access
- 4 September 2025
- Published by Springer Nature in Applied Physics B
- Vol. 131 (10) , 1
Correction: Continuum laser absorption spectroscopy of C2(a3Πu) in a sublimating cloud of carbon black
- 4 September 2025
- Published by Springer Nature in Applied Physics B
- Vol. 131 (10) , 1
Open AccessCorrection: Continuum laser absorption spectroscopy of C2(a3Πu) in a sublimating cloud of carbon black
- Open Access
- 29 July 2025
- Published by Springer Nature in Applied Physics B
- Vol. 131 (8) , 1-13
Continuum laser absorption spectroscopy of C2(a3Πu) in a sublimating cloud of carbon black
A direct optical absorption diagnostic has been developed for rotationally resolved measurements of diatomic carbon (a3Πu→d3Πg (0,0) and (1,1)) at a repetition rate of 525 kHz and resolution of 7.3 pm over the range of 511.1–514.1 nm. The diagnostic utilizes a high-power pulsed continuum laser light source dispersed in a spectrograph and imaged by a high-speed camera. Measurements have been performed that capture the temporal evolution of C2 number density and temperature of a cloud of carbon black sublimating in shock heated gas at high temperature and pressure (T = 5500 K, P = 3.7 atm). A simultaneous light absorption measurement of the condensed phase enables comparisons of the gaseous C2 number density to the condensed phase mass. The continuum laser absorption diagnostic is applied to C2 in this work but shows promise in being a simple “drop-in” system for absorption spectroscopy in the visible range at rapid repetition rates and high dispersion, filling an important gap for laser diagnostic systems.
- 29 July 2025
- Published by Springer Nature in Applied Physics B
- Vol. 131 (8) , 1-13
Open AccessContinuum laser absorption spectroscopy of C2(a3Πu) in a sublimating cloud of carbon black
A direct optical absorption diagnostic has been developed for rotationally resolved measurements of diatomic carbon (a3Πu→d3Πg (0,0) and (1,1)) at a repetition rate of 525 kHz and resolution of 7.3 pm over the range of 511.1–514.1 nm. The diagnostic utilizes a high-power pulsed continuum laser light source dispersed in a spectrograph and imaged by a high-speed camera. Measurements have been performed that capture the temporal evolution of C2 number density and temperature of a cloud of carbon black sublimating in shock heated gas at high temperature and pressure (T = 5500 K, P = 3.7 atm). A simultaneous light absorption measurement of the condensed phase enables comparisons of the gaseous C2 number density to the condensed phase mass. The continuum laser absorption diagnostic is applied to C2 in this work but shows promise in being a simple “drop-in” system for absorption spectroscopy in the visible range at rapid repetition rates and high dispersion, filling an important gap for laser diagnostic systems.
- 21 January 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (2)
Direct optical absorption detection of metal vapor in mechanically stimulated gas emission
Optical absorption spectroscopy has been used to detect neutral atomic emission from surfaces undergoing deformation at high strain rates due to shock waves induced by high explosive detonation. Magnesium and zinc alloys are investigated, and four atomic species Mg, Zn, Pb, and Sn are detected in single-shot absorption spectra. This technique offers the potential to study mechanically stimulated gas emission with quantification of the spatial and temporal variations of the emission event.
- 21 January 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (2)
Direct optical absorption detection of metal vapor in mechanically stimulated gas emission
Optical absorption spectroscopy has been used to detect neutral atomic emission from surfaces undergoing deformation at high strain rates due to shock waves induced by high explosive detonation. Magnesium and zinc alloys are investigated, and four atomic species Mg, Zn, Pb, and Sn are detected in single-shot absorption spectra. This technique offers the potential to study mechanically stimulated gas emission with quantification of the spatial and temporal variations of the emission event.
- 27 July 2024
- Published by Taylor & Francis in Spectroscopy Letters
- Vol. 57 (9) , 545-552
Temporal evolution of absorption spectra for diisopropyl methylphosphonate at high temperatures in a shock tube
- 27 July 2024
- Published by Taylor & Francis in Spectroscopy Letters
- Vol. 57 (9) , 545-552
Temporal evolution of absorption spectra for diisopropyl methylphosphonate at high temperatures in a shock tube
- 7 May 2024
- Published by SAGE Publications in Applied Spectroscopy
- Vol. 78 (7) , 692-701
Emission Spectra of Uranium Particulates at High Temperature
The emission spectrum of micron-scale uranium particulates at high temperatures in the ultraviolet, visible, and near-infrared spectral regions is investigated using a heterogeneous shock tube. Temperatures from 3000 to 9000 K are characterized in an inert argon environment and with incremental amounts of added oxygen. Atomic line spectra do not emerge above the continuum emission spectrum until between 4500 and 5000 K in pure argon, and 6100 and 6600 K in 1% oxygen. For 5% oxygen, however, the threshold for atomic emission drops below 3800 K. Uranium monoxide molecular emission in the strongest visible band at 595.4 nm is not observed at any condition. Uncertainties in particle temperature determination in high-temperature shock tube environments are discussed, and limitations to such measurements are presented, such as those from experimental factors such as the powder loading method and expected detection limits of uranium species in relevant conditions.
- 7 May 2024
- Published by SAGE Publications in Applied Spectroscopy
- Vol. 78 (7) , 692-701
Emission Spectra of Uranium Particulates at High Temperature
The emission spectrum of micron-scale uranium particulates at high temperatures in the ultraviolet, visible, and near-infrared spectral regions is investigated using a heterogeneous shock tube. Temperatures from 3000 to 9000 K are characterized in an inert argon environment and with incremental amounts of added oxygen. Atomic line spectra do not emerge above the continuum emission spectrum until between 4500 and 5000 K in pure argon, and 6100 and 6600 K in 1% oxygen. For 5% oxygen, however, the threshold for atomic emission drops below 3800 K. Uranium monoxide molecular emission in the strongest visible band at 595.4 nm is not observed at any condition. Uncertainties in particle temperature determination in high-temperature shock tube environments are discussed, and limitations to such measurements are presented, such as those from experimental factors such as the powder loading method and expected detection limits of uranium species in relevant conditions.
- Open Access
- 16 November 2022
- Published by Wiley in Journal of Combustion
- Vol. 2022, 1-23
Uranium Dust Cloud Combustion: Burning Characteristics and Absorption Spectroscopy Measurements
This study characterized uranium metal dust cloud combustion using absorption spectroscopy, imaging, and broadband emission measurements. Other metals were similarly combusted to establish correlations between results from this study and those found in the literature. It was determined that the burn temperature of uranium was limited to the volatilization temperature of uranium dioxide. Combustion behavior was similar to that of other refractory metals in terms of burn time and the observation of exploding particle behavior.
- 16 November 2022
- Published by Wiley in Journal of Combustion
- Vol. 2022, 1-23
Open AccessUranium Dust Cloud Combustion: Burning Characteristics and Absorption Spectroscopy Measurements
This study characterized uranium metal dust cloud combustion using absorption spectroscopy, imaging, and broadband emission measurements. Other metals were similarly combusted to establish correlations between results from this study and those found in the literature. It was determined that the burn temperature of uranium was limited to the volatilization temperature of uranium dioxide. Combustion behavior was similar to that of other refractory metals in terms of burn time and the observation of exploding particle behavior.
- 19 January 2022
- Published by SAGE Publications in Applied Spectroscopy
- Vol. 76 (3) , 310-317
Ultraviolet Emissions from Explosive Detonation Breakout
Detailed spectroscopic measurements of high explosive detonation breakout in the ultraviolet region are presented. Molecular features associated with CN, NH, OH, and N 2 are observed and analyzed. Spectra indicate extreme temperatures well in excess of 5000 K in the first few microseconds after breakout. Molecular bands are found to originate from the detonation products, as opposed to the ambient air, and are strongly attenuated in the presence of oxygen. Implications for forensic analysis of source explosive are discussed.
- 19 January 2022
- Published by SAGE Publications in Applied Spectroscopy
- Vol. 76 (3) , 310-317
Ultraviolet Emissions from Explosive Detonation Breakout
Detailed spectroscopic measurements of high explosive detonation breakout in the ultraviolet region are presented. Molecular features associated with CN, NH, OH, and N 2 are observed and analyzed. Spectra indicate extreme temperatures well in excess of 5000 K in the first few microseconds after breakout. Molecular bands are found to originate from the detonation products, as opposed to the ambient air, and are strongly attenuated in the presence of oxygen. Implications for forensic analysis of source explosive are discussed.
- 9 September 2021
- Published by SAGE Publications in Applied Spectroscopy
- Vol. 75 (11) , 1410-1418
Spectral Emission Signatures from Cased High‐Explosive Charges
Spectroscopic signatures of cased high-explosive charge denotations are examined using emission spectroscopy with sub nanometer resolution. Eleven distinct case materials are investigated for atomic features of their major alloying elements. Molecular features of case material combustion products are also investigated for five case materials. Emission is monitored within the 275–425 nm range for atomic features and in the 310–755 nm range for molecular features. Major alloying elements with concentrations greater than 5% are generally detected through atomic emission. Al, Cu, Fe, Mg, Cr, Mn, Pb, and Ni are all detected in concentrations less than 5%. Undetected elements include Zn, Nb, Ta, and V. Molecular emission from aluminum monoxide, titanium monoxide, and CN is measured for aluminum alloy, titanium alloy, and carbon fiber cases, respectively.
- 9 September 2021
- Published by SAGE Publications in Applied Spectroscopy
- Vol. 75 (11) , 1410-1418
Spectral Emission Signatures from Cased High‐Explosive Charges
Spectroscopic signatures of cased high-explosive charge denotations are examined using emission spectroscopy with sub nanometer resolution. Eleven distinct case materials are investigated for atomic features of their major alloying elements. Molecular features of case material combustion products are also investigated for five case materials. Emission is monitored within the 275–425 nm range for atomic features and in the 310–755 nm range for molecular features. Major alloying elements with concentrations greater than 5% are generally detected through atomic emission. Al, Cu, Fe, Mg, Cr, Mn, Pb, and Ni are all detected in concentrations less than 5%. Undetected elements include Zn, Nb, Ta, and V. Molecular emission from aluminum monoxide, titanium monoxide, and CN is measured for aluminum alloy, titanium alloy, and carbon fiber cases, respectively.
- Open Access
Electrical Properties of Reversed-Polarity Ball Plasmoid Discharges
Ball plasmoid discharges are a unique type of atmospheric-pressure plasma discharge with a lifetime on the order of a hundred milliseconds without attachment to a power source. These discharges are generated by a moderate current pulse over the surface of an aqueous electrolyte, and some consider the spherical plasmoid that results to bear some resemblance to ball lightning. This article presents the first analysis of the electrical properties of ball plasmoid discharges in a reversed-polarity configuration, i.e., with the central electrode serving as the anode rather than as the cathode. These experiments demonstrate that ball plasmoids can indeed be generated with either electrode polarity with similar observable properties. These results are contrary to what has previously been discussed in the literature and raise additional questions regarding formation mechanisms of ball plasmoids. Analysis of images and electrical measurements collected at various discharge energies show that two distinct processes occur during discharges with our circuitry and in this reversed-polarity configuration: the formation of spark channels between the anode and electrolyte, and the generation of streamers and a jet from the surface of the anode.
Open AccessElectrical Properties of Reversed-Polarity Ball Plasmoid Discharges
Ball plasmoid discharges are a unique type of atmospheric-pressure plasma discharge with a lifetime on the order of a hundred milliseconds without attachment to a power source. These discharges are generated by a moderate current pulse over the surface of an aqueous electrolyte, and some consider the spherical plasmoid that results to bear some resemblance to ball lightning. This article presents the first analysis of the electrical properties of ball plasmoid discharges in a reversed-polarity configuration, i.e., with the central electrode serving as the anode rather than as the cathode. These experiments demonstrate that ball plasmoids can indeed be generated with either electrode polarity with similar observable properties. These results are contrary to what has previously been discussed in the literature and raise additional questions regarding formation mechanisms of ball plasmoids. Analysis of images and electrical measurements collected at various discharge energies show that two distinct processes occur during discharges with our circuitry and in this reversed-polarity configuration: the formation of spark channels between the anode and electrolyte, and the generation of streamers and a jet from the surface of the anode.