Sebastian Mack
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Sebastian Mack has a total of 71 co-authors. Here are the top co-authors by number of shared publications:
Andreas Wolf
Fraunhofer Institute for Solar Energy Systems ISE, Freiburg, Germany
7 shared publications- Andreas Wolf
Fraunhofer Institute for Solar Energy Systems, Freiburg, Germany
3 shared publications Katrin Krieg
Fraunhofer ISE Freiburg Germany
3 shared publicationsMartijn Lenes
Tempress Systems Radeweg 31 Vaassen 8171 MD The Netherlands
3 shared publications- Andreas Lorenz
Fraunhofer Institute for Solar Energy Systems ISE, Freiburg, Germany
2 shared publications - Bishal Kafle
Fraunhofer Institute for Solar Energy Systems ISE, Freiburg, Germany
2 shared publications
Latest Publications
- Open Access
- 23 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 16 (3) , 313-320
Progress in Fine-Line Front-Side Printing for TOPCon Solar Cells
As the silver price sets one record height after another, to curb costs, the need to reduce silver consumption in solar cell metallization increases. This work develops front-side metallization for tunnel oxide passivating contact (TOPCon) solar cells toward fine-line printing, i.e., feature sizes of less than 20 μm in width and a reduction of wet paste laydown. Besides silver reduction, this is motivated by increasing conversion efficiency, which further reduces cost per watt. To reach these goals by screen printing, three different fine-mesh configurations for knotless screens are utilized. Nominal screen opening widths vary from 24 µm to 13 μm. Moreover, printing with a dual-layer stencil featuring a nominal opening width of 9 μm is analyzed. The printed and fired contacts are characterized toward key geometrical and electrical performance indicators. Based on the corresponding findings, M10-sized TOPCon solar cells featuring fine-line grids with a core finger width wc = (16 ± 1) μm were fabricated. Compared to the reference group with wc = (23 ± 2) μm, a conversion efficiency gain of (0.9 ± 0.2)% rel is achieved, which is mainly driven by a reduction of shading-induced losses. Furthermore, wet paste laydown on the front is reduced by ∼30% rel using such metallization.
- 23 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 16 (3) , 313-320
Open AccessProgress in Fine-Line Front-Side Printing for TOPCon Solar Cells
As the silver price sets one record height after another, to curb costs, the need to reduce silver consumption in solar cell metallization increases. This work develops front-side metallization for tunnel oxide passivating contact (TOPCon) solar cells toward fine-line printing, i.e., feature sizes of less than 20 μm in width and a reduction of wet paste laydown. Besides silver reduction, this is motivated by increasing conversion efficiency, which further reduces cost per watt. To reach these goals by screen printing, three different fine-mesh configurations for knotless screens are utilized. Nominal screen opening widths vary from 24 µm to 13 μm. Moreover, printing with a dual-layer stencil featuring a nominal opening width of 9 μm is analyzed. The printed and fired contacts are characterized toward key geometrical and electrical performance indicators. Based on the corresponding findings, M10-sized TOPCon solar cells featuring fine-line grids with a core finger width wc = (16 ± 1) μm were fabricated. Compared to the reference group with wc = (23 ± 2) μm, a conversion efficiency gain of (0.9 ± 0.2)% rel is achieved, which is mainly driven by a reduction of shading-induced losses. Furthermore, wet paste laydown on the front is reduced by ∼30% rel using such metallization.
- Open Access
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 16 (3) , 353-360
Inline Plating of Ni/Cu Contacts for Industrial TOPCon Si Solar Cells—Status and Outlook
This article explores an inline plating metallization technique aimed at reducing silver usage in the production of tunnel oxide passivated contact (TOPCon) silicon solar cells. Utilizing ultrashort-pulse UV laser patterning combined with electrochemical deposition of Ni, Cu, and Ag, this approach has successfully achieved efficiencies up to 24% with silver consumption reduced to 1.1 mg/Wp. The process has been applied using pilot line equipment developed by RENA Technologies GmbH. This work not only demonstrates the potential of inline plating for cost-effective solar cell manufacturing but also addresses industrially feasible mitigation strategies for challenges such as contact adhesion and process stability. These include strategies to avoid insufficient Ni nucleation and uneven plating current injection, which are critical for achieving low contact resistivity and high fill factors (FF). As a result, FF of (82.1 ± 0.3)% were demonstrated for a batch of 186 TOPCon solar cells (M10 wafer size). In addition, reliability tests on fabricated mini modules demonstrate promising resistance to degradation. This research advances TOPCon solar cell technology by providing deeper insights into the piloting of inline plating technology for cost-effective and silver-lean metallization of TOPCon solar cells.
- 23 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 16 (3) , 353-360
Open AccessInline Plating of Ni/Cu Contacts for Industrial TOPCon Si Solar Cells—Status and Outlook
This article explores an inline plating metallization technique aimed at reducing silver usage in the production of tunnel oxide passivated contact (TOPCon) silicon solar cells. Utilizing ultrashort-pulse UV laser patterning combined with electrochemical deposition of Ni, Cu, and Ag, this approach has successfully achieved efficiencies up to 24% with silver consumption reduced to 1.1 mg/Wp. The process has been applied using pilot line equipment developed by RENA Technologies GmbH. This work not only demonstrates the potential of inline plating for cost-effective solar cell manufacturing but also addresses industrially feasible mitigation strategies for challenges such as contact adhesion and process stability. These include strategies to avoid insufficient Ni nucleation and uneven plating current injection, which are critical for achieving low contact resistivity and high fill factors (FF). As a result, FF of (82.1 ± 0.3)% were demonstrated for a batch of 186 TOPCon solar cells (M10 wafer size). In addition, reliability tests on fabricated mini modules demonstrate promising resistance to degradation. This research advances TOPCon solar cell technology by providing deeper insights into the piloting of inline plating technology for cost-effective and silver-lean metallization of TOPCon solar cells.
- Open Access
Microstructure Analysis of Current‐Fired Contacts on TOPCon Layers
We report on the analysis of the microstructure of a current‐fired contact formed by screen printing, drying, and sintering of a silver paste and subsequent laser‐enhanced contact optimization (LECO) for silicon solar cells with tunnel‐oxide passivated contacts (TOPCon) on the TOPCon side. The analysis is based on scanning electron microscopy and energy dispersive X‐ray spectroscopy. We show that a new phase is formed during LECO at individual points of the interface between the contact finger and the polycrystalline silicon layer consisting of silver and silicon. The altered material combination is confined to the metal and the polycrystalline layer only and does not penetrate through the tunnel oxide into the silicon wafer. We conclude that the mechanism for the contact formation on the TOPCon stack is very similar to the one reported for the front contact of passivated emitter and rear cells.
Open AccessMicrostructure Analysis of Current‐Fired Contacts on TOPCon Layers
We report on the analysis of the microstructure of a current‐fired contact formed by screen printing, drying, and sintering of a silver paste and subsequent laser‐enhanced contact optimization (LECO) for silicon solar cells with tunnel‐oxide passivated contacts (TOPCon) on the TOPCon side. The analysis is based on scanning electron microscopy and energy dispersive X‐ray spectroscopy. We show that a new phase is formed during LECO at individual points of the interface between the contact finger and the polycrystalline silicon layer consisting of silver and silicon. The altered material combination is confined to the metal and the polycrystalline layer only and does not penetrate through the tunnel oxide into the silicon wafer. We conclude that the mechanism for the contact formation on the TOPCon stack is very similar to the one reported for the front contact of passivated emitter and rear cells.
- Open Access
Development of Boron Emitters for Tunnel Oxide Passivated Contact Solar Cells with Current‐Assisted Contact Formation
Front side recombination in tunnel oxide passivated contact solar cells is frequently described by the recombination parameters j0e for the passivated and j0e,met for the metallized front region. The combination of Al‐free metallization pastes and current‐assisted contact formation has shown significant reduction of j0e,met. Such new metallization approaches enable shallower doping profiles and higher sheet resistances Rsheet, which in turn also reduce j0e. In this study, we provide insight into how to reduce the overall front side recombination, by tailoring the boron dopant profile from atmospheric pressure BBr3 diffusion processes. The limitation of the dopant dose in the profile leads to a higher Rsheet of the resulting profile. The newly developed homogeneous boron emitter features j0e = 14 fA cm−2 at a Rsheet = 161 Ω sq−1, a 62% decrease from the initial value, and an even lower j0e = 8 fA cm−2 is determined for an emitter with 330 Ω sq−1. An increased contact resistivity on the front side still poses a challenge for Ag front side pastes despite the use of current‐assisted contact formation. Application of an alternative AgAl paste in industrial‐type fabricated TOPCon solar cells results in a maximum conversion efficiency of 24.5%.
Open AccessDevelopment of Boron Emitters for Tunnel Oxide Passivated Contact Solar Cells with Current‐Assisted Contact Formation
Front side recombination in tunnel oxide passivated contact solar cells is frequently described by the recombination parameters j0e for the passivated and j0e,met for the metallized front region. The combination of Al‐free metallization pastes and current‐assisted contact formation has shown significant reduction of j0e,met. Such new metallization approaches enable shallower doping profiles and higher sheet resistances Rsheet, which in turn also reduce j0e. In this study, we provide insight into how to reduce the overall front side recombination, by tailoring the boron dopant profile from atmospheric pressure BBr3 diffusion processes. The limitation of the dopant dose in the profile leads to a higher Rsheet of the resulting profile. The newly developed homogeneous boron emitter features j0e = 14 fA cm−2 at a Rsheet = 161 Ω sq−1, a 62% decrease from the initial value, and an even lower j0e = 8 fA cm−2 is determined for an emitter with 330 Ω sq−1. An increased contact resistivity on the front side still poses a challenge for Ag front side pastes despite the use of current‐assisted contact formation. Application of an alternative AgAl paste in industrial‐type fabricated TOPCon solar cells results in a maximum conversion efficiency of 24.5%.
- Open Access
- 8 January 2025
- Published by EDP Sciences in EPJ Photovoltaics
- Vol. 16, 6
Project “BUSSARD” − a holistic development of high-efficiency solar cells covering innovative front-end, metallization and interconnection approaches
Within this work, we present key results of the transnational European research project “Bussard”. The aim of this project is the development and evaluation of various innovative approaches for highly efficient cell concepts such as tunnel oxide passivating contact (TOPCon) solar cells considering the whole process chain including front-end, back-end and module processing. We present atomic layer deposition (ALD) as a high-throughput alternative for the deposition of Al2O3 passivation layers on the front side of TOPCon solar cells enabling a substantial reduction of the emitter saturation current density down to j0e = 13 fA/cm2. In the field of metallization, we evaluate and demonstrate three innovative approaches for the fine-line metallization of TOPCon solar cells. In this study we focus on multi-nozzle parallel dispensing, a technology that was developed as an alternative to standard screen-printing metallization and is used for the metallization of TOPCon solar cells for the first time. By optimizing the fabrication process at Fraunhofer ISE, we realize TOPCon solar cells (156.75 mm × 156.75 mm) with a champion conversion efficiency of up to ηmax = 24.2% (independently confirmed by Fraunhofer ISE CalLab PVCells). Finally, we present a comprehensive evaluation of the innovative Tape Solution interconnection concept for TOPCon cells and modules. We demonstrate the feasibility on small-scale and full-format modules and analyze the I–V results as well as cell-to-module (CTM) loss analysis using the simulation tool SmartCalc®. The results are compared to TOPCon modules interconnected via SmartWire Connection Technology (SWCT) and electrically conductive adhesive (ECA).
- 8 January 2025
- Published by EDP Sciences in EPJ Photovoltaics
- Vol. 16, 6
Open AccessProject “BUSSARD” − a holistic development of high-efficiency solar cells covering innovative front-end, metallization and interconnection approaches
Within this work, we present key results of the transnational European research project “Bussard”. The aim of this project is the development and evaluation of various innovative approaches for highly efficient cell concepts such as tunnel oxide passivating contact (TOPCon) solar cells considering the whole process chain including front-end, back-end and module processing. We present atomic layer deposition (ALD) as a high-throughput alternative for the deposition of Al2O3 passivation layers on the front side of TOPCon solar cells enabling a substantial reduction of the emitter saturation current density down to j0e = 13 fA/cm2. In the field of metallization, we evaluate and demonstrate three innovative approaches for the fine-line metallization of TOPCon solar cells. In this study we focus on multi-nozzle parallel dispensing, a technology that was developed as an alternative to standard screen-printing metallization and is used for the metallization of TOPCon solar cells for the first time. By optimizing the fabrication process at Fraunhofer ISE, we realize TOPCon solar cells (156.75 mm × 156.75 mm) with a champion conversion efficiency of up to ηmax = 24.2% (independently confirmed by Fraunhofer ISE CalLab PVCells). Finally, we present a comprehensive evaluation of the innovative Tape Solution interconnection concept for TOPCon cells and modules. We demonstrate the feasibility on small-scale and full-format modules and analyze the I–V results as well as cell-to-module (CTM) loss analysis using the simulation tool SmartCalc®. The results are compared to TOPCon modules interconnected via SmartWire Connection Technology (SWCT) and electrically conductive adhesive (ECA).
- Open Access
- 8 January 2025
- Published by EDP Sciences in EPJ Photovoltaics
- Vol. 16, 5
Approaches for reducing metallization-induced losses in industrial TOPCon solar cells
Minimizing carrier recombination in silicon solar cells is key to increase the conversion efficiency, as recombination affects both the fill factor and the open circuit voltage. Recombination at metal-semiconductor interfaces plays a crucial part in this, however, processing conditions which lead to low recombination, such as e.g., a low firing set temperature or the use of thick dielectrics, typically result in increased contact resistivities. Also, a too low firing set temperature leads to an incomplete hydrogenation of the interfaces. Recently, laser-enhanced contact optimization has been introduced to decouple recombination and contact properties to some extent, which allows for high fill factors and high open circuit voltages, and which explains the growing interest from manufacturers in that technology. We elucidate on the need for improved hydrogenation of interfaces, which contradicts the wish to decrease firing temperatures for reduced carrier recombination at metal-semiconductor interfaces. The implementation of an additional annealing step, e.g. in a tube furnace, after dielectric surface passivation is shown to lead to improved passivation properties so that the thermal budget during contact firing can be optimized to minimize contact resistivities. Overall, contact optimization allows for solar cell efficiencies of 24.1%, measured at an industrial cell tester, for a traditional approach without additional annealing step, and applying an AgAl front side metallization paste. A comparison of Ag and AgAl front side metallization pastes reveals a higher open circuit voltage for the Ag paste, at the drawback of an increased contact resistivity.
- 8 January 2025
- Published by EDP Sciences in EPJ Photovoltaics
- Vol. 16, 5
Open AccessApproaches for reducing metallization-induced losses in industrial TOPCon solar cells
Minimizing carrier recombination in silicon solar cells is key to increase the conversion efficiency, as recombination affects both the fill factor and the open circuit voltage. Recombination at metal-semiconductor interfaces plays a crucial part in this, however, processing conditions which lead to low recombination, such as e.g., a low firing set temperature or the use of thick dielectrics, typically result in increased contact resistivities. Also, a too low firing set temperature leads to an incomplete hydrogenation of the interfaces. Recently, laser-enhanced contact optimization has been introduced to decouple recombination and contact properties to some extent, which allows for high fill factors and high open circuit voltages, and which explains the growing interest from manufacturers in that technology. We elucidate on the need for improved hydrogenation of interfaces, which contradicts the wish to decrease firing temperatures for reduced carrier recombination at metal-semiconductor interfaces. The implementation of an additional annealing step, e.g. in a tube furnace, after dielectric surface passivation is shown to lead to improved passivation properties so that the thermal budget during contact firing can be optimized to minimize contact resistivities. Overall, contact optimization allows for solar cell efficiencies of 24.1%, measured at an industrial cell tester, for a traditional approach without additional annealing step, and applying an AgAl front side metallization paste. A comparison of Ag and AgAl front side metallization pastes reveals a higher open circuit voltage for the Ag paste, at the drawback of an increased contact resistivity.
- Top Cited PapersOpen Access
UV‐Induced Degradation of Industrial PERC, TOPCon, and HJT Solar Cells: The Next Big Reliability Challenge?
With the surge of UV‐transparent module encapsulants in the photovoltaic industry aiming to boost quantum efficiency, modern silicon solar cells must now inherently withstand UV exposure. UV‐induced degradation (UVID) of nonencapsulated laboratory and industrial solar cells from several manufacturers is investigated. Passivated emitter rear contact (PERC), tunnel oxide passivating contact (TOPCon), and silicon heterojunction (HJT) cells can suffer from severe implied voltage degradation (>20 mV) after UV exposure relating to 3.8 years of module installation in the Negev desert. Front UV‐exposure causes more performance loss than an equal rear dose. This is connected to a higher UV transmission of the cell layers outside the bulk, indicating the photons need to reach the silicon surface to induce damage. Current–voltage measurements of the TOPCon groups most sensitive to UV degradation show more than 7%rel efficiency loss with the Voc as the main contributor. For two TOPCon groups, dark storage for 14 days after UV exposure causes an additional voltage drop on a similar scale as the UV damage itself, impeding straightforward reliability testing. UVID appears to be a complex process general to all dominant cell architectures with the potential to diminish efforts in efficiency optimization within only a few years of field employment.
Top Cited PapersOpen AccessUV‐Induced Degradation of Industrial PERC, TOPCon, and HJT Solar Cells: The Next Big Reliability Challenge?
With the surge of UV‐transparent module encapsulants in the photovoltaic industry aiming to boost quantum efficiency, modern silicon solar cells must now inherently withstand UV exposure. UV‐induced degradation (UVID) of nonencapsulated laboratory and industrial solar cells from several manufacturers is investigated. Passivated emitter rear contact (PERC), tunnel oxide passivating contact (TOPCon), and silicon heterojunction (HJT) cells can suffer from severe implied voltage degradation (>20 mV) after UV exposure relating to 3.8 years of module installation in the Negev desert. Front UV‐exposure causes more performance loss than an equal rear dose. This is connected to a higher UV transmission of the cell layers outside the bulk, indicating the photons need to reach the silicon surface to induce damage. Current–voltage measurements of the TOPCon groups most sensitive to UV degradation show more than 7%rel efficiency loss with the Voc as the main contributor. For two TOPCon groups, dark storage for 14 days after UV exposure causes an additional voltage drop on a similar scale as the UV damage itself, impeding straightforward reliability testing. UVID appears to be a complex process general to all dominant cell architectures with the potential to diminish efforts in efficiency optimization within only a few years of field employment.
- Open Access
- 31 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 12 (6) , 1393-1399
Stack Diffusion Process for Cost- and Energy-Efficient Boron Emitter Formation
The boron emitter formation for tunnel oxide passivated contact (TOPCon) solar cells faces higher costs compared to the POCl 3 diffusion for passivated emitter and rear (PERC) solar cells due to the requirement for higher temperatures and longer process times. This work presents an alternative energy-efficient and low cost of ownership boron diffusion approach for TOPCon solar cells, enabling a highly increased throughput compared to the typically used gas phase diffusion. We use an atmospheric pressure chemical vapor deposition borosilicate glass layer as the boron dopant source and combine it with a subsequent thermal anneal in a quartz tube furnace for dopant drive-in. Here, we either use a conventional single-slot quartz boat configuration, or, for highly increased throughput, a vertical wafer stack configuration with the wafer surfaces in direct contact with each other. We show that this approach yields an emitter doping profile comparable to the state-of-the-art gas phase diffusion with sufficient uniformity across the wafer area. We further investigate the emitter dark saturation current densities j 0e as well as the energy conversion efficiency of TOPCon solar cells fabricated for each configuration and compare the results to those of a BBr 3 reference process. These solar cells achieve energy conversion efficiencies exceeding 23% for the stack diffusion approach. Additionally, we demonstrate a potential reduction in both the cost of ownership and the specific electricity consumption of the presented approach.
- 31 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 12 (6) , 1393-1399
Open AccessStack Diffusion Process for Cost- and Energy-Efficient Boron Emitter Formation
The boron emitter formation for tunnel oxide passivated contact (TOPCon) solar cells faces higher costs compared to the POCl 3 diffusion for passivated emitter and rear (PERC) solar cells due to the requirement for higher temperatures and longer process times. This work presents an alternative energy-efficient and low cost of ownership boron diffusion approach for TOPCon solar cells, enabling a highly increased throughput compared to the typically used gas phase diffusion. We use an atmospheric pressure chemical vapor deposition borosilicate glass layer as the boron dopant source and combine it with a subsequent thermal anneal in a quartz tube furnace for dopant drive-in. Here, we either use a conventional single-slot quartz boat configuration, or, for highly increased throughput, a vertical wafer stack configuration with the wafer surfaces in direct contact with each other. We show that this approach yields an emitter doping profile comparable to the state-of-the-art gas phase diffusion with sufficient uniformity across the wafer area. We further investigate the emitter dark saturation current densities j 0e as well as the energy conversion efficiency of TOPCon solar cells fabricated for each configuration and compare the results to those of a BBr 3 reference process. These solar cells achieve energy conversion efficiencies exceeding 23% for the stack diffusion approach. Additionally, we demonstrate a potential reduction in both the cost of ownership and the specific electricity consumption of the presented approach.
- Open Access
- 16 August 2022
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 30 (12) , 1393-1399
Laser‐enhanced contact optimization oniTOPCon solar cells
The authors present their work on laser‐enhanced contact optimization (LECO) oniTOPCon solar cells. LECO improves the metal‐semi‐conductor contact resistivityρcon the boron emitter and the n‐TOPCon side from an underfired (thermal budget too low) state of 2.9 and 14.1 mΩcm2to an enhanced state of 1.8 and 2.9 mΩcm2. Therefore, it enables the reduction of the optimal peak firing temperature, which leads to a decrease of metal induced recombination mainly on the boron emitter side and to minor degree on the n‐TOPCon side, as shown in this work. Ultimately, LECO improvesiTOPCon solar cells conversion efficiency by 0.6%abscompared with the optimal fired, untreated reference. Submitting those cells to 140°C and 2 suns equivalent irradiation for more than 4 h shows no impact on the conversion efficiency or any sign of light and elevated temperature‐induced degradation (LeTID). Confirmed by ISE CalLab, LECO improvediTOPCon solar cells reach 23.8% and 24.1% conversion efficiency on industrial typical wafer formats and processes.
- 16 August 2022
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 30 (12) , 1393-1399
Open AccessLaser‐enhanced contact optimization oniTOPCon solar cells
The authors present their work on laser‐enhanced contact optimization (LECO) oniTOPCon solar cells. LECO improves the metal‐semi‐conductor contact resistivityρcon the boron emitter and the n‐TOPCon side from an underfired (thermal budget too low) state of 2.9 and 14.1 mΩcm2to an enhanced state of 1.8 and 2.9 mΩcm2. Therefore, it enables the reduction of the optimal peak firing temperature, which leads to a decrease of metal induced recombination mainly on the boron emitter side and to minor degree on the n‐TOPCon side, as shown in this work. Ultimately, LECO improvesiTOPCon solar cells conversion efficiency by 0.6%abscompared with the optimal fired, untreated reference. Submitting those cells to 140°C and 2 suns equivalent irradiation for more than 4 h shows no impact on the conversion efficiency or any sign of light and elevated temperature‐induced degradation (LeTID). Confirmed by ISE CalLab, LECO improvediTOPCon solar cells reach 23.8% and 24.1% conversion efficiency on industrial typical wafer formats and processes.
- Open Access
Progress in p‐type Tunnel Oxide‐Passivated Contact Solar Cells with Screen‐Printed Contacts
Herein, an update on the work on high‐efficiency p‐type solar cells with p‐type‐passivating rear contacts formed by low‐pressure chemical vapor deposition and screen‐printed contacts is given. It is shown that thin polysilicon layers enable a high level of surface passivation but do show increased contact resistivity and especially contact recombination. Commercially available pastes and dependence of contact resistivity and contact recombination on polylayer thickness and firing set temperature are investigated. For 240 nm‐thick poly‐Si layers, the values down to 4 mΩ cm2 and 60 fA cm−2 are observed. For the presented process sequence, improved hydrogenation as one possibility to increase the passivation quality of the passivating contact structure is identified. Implementing all findings into a final solar cell, a maximum total area conversion efficiency of 21.2% is reported.
Open AccessProgress in p‐type Tunnel Oxide‐Passivated Contact Solar Cells with Screen‐Printed Contacts
Herein, an update on the work on high‐efficiency p‐type solar cells with p‐type‐passivating rear contacts formed by low‐pressure chemical vapor deposition and screen‐printed contacts is given. It is shown that thin polysilicon layers enable a high level of surface passivation but do show increased contact resistivity and especially contact recombination. Commercially available pastes and dependence of contact resistivity and contact recombination on polylayer thickness and firing set temperature are investigated. For 240 nm‐thick poly‐Si layers, the values down to 4 mΩ cm2 and 60 fA cm−2 are observed. For the presented process sequence, improved hydrogenation as one possibility to increase the passivation quality of the passivating contact structure is identified. Implementing all findings into a final solar cell, a maximum total area conversion efficiency of 21.2% is reported.