Candice Mezel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Candice Mezel has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Antoine Bourgeade
CEA-CESTA, 15 Avenue des Sablières, CS 60001, F33116 Le Barp Cedex, France
2 shared publications - Ludovic Hallo
Centre Lasers Intenses et Applications, UMR 5107 CEA V CNRS – Université Bordeaux 1
2 shared publications A Souquet
1 shared publication- Agnès Souquet
Inserm, U577
1 shared publication - Bertrand Guillotin
Bioingénierie Tissulaire, Inserm, Université Bordeaux Segalen, France
1 shared publication F Guillemot
1 shared publication
Latest Publications
- 21 May 2010
- Published by Springer Nature in Journal of Scientific Computing
- Vol. 44 (2) , 170-190
Modeling the Early Ionization of Dielectrics by Ultrashort Laser Pulses
- 21 May 2010
- Published by Springer Nature in Journal of Scientific Computing
- Vol. 44 (2) , 170-190
Modeling the Early Ionization of Dielectrics by Ultrashort Laser Pulses
- 1 March 2010
- Published by IOP Publishing in Biofabrication
- Vol. 2 (1) , 014103
Bioprinting by laser-induced forward transfer for tissue engineering applications: jet formation modeling
In this paper, a nanosecond LIFT process is analyzed both from experimental and modeling points of view. Experimental results are first presented and compared to simple estimates obtained from physical analysis, i.e. energy balance, jump relations and analytical pocket dynamics. Then a self-consistent 2D axisymmetric modeling strategy is presented. It is shown that data accessible from experiments, i.e. jet diameter and velocity, can be reproduced. Moreover, some specific mechanisms involved in the rear-surface deformation and jet formation may be described by some scales of hydrodynamic process, i.e. shock waves propagation and expansion waves, as a consequence of the laser heating. It shows that the LIFT process is essentially driven by hydrodynamics and thermal transfer, and that a coupled approach including self-consistent laser energy deposition, heating by thermal conduction and specific models for matter is required.
- 1 March 2010
- Published by IOP Publishing in Biofabrication
- Vol. 2 (1) , 014103
Bioprinting by laser-induced forward transfer for tissue engineering applications: jet formation modeling
In this paper, a nanosecond LIFT process is analyzed both from experimental and modeling points of view. Experimental results are first presented and compared to simple estimates obtained from physical analysis, i.e. energy balance, jump relations and analytical pocket dynamics. Then a self-consistent 2D axisymmetric modeling strategy is presented. It is shown that data accessible from experiments, i.e. jet diameter and velocity, can be reproduced. Moreover, some specific mechanisms involved in the rear-surface deformation and jet formation may be described by some scales of hydrodynamic process, i.e. shock waves propagation and expansion waves, as a consequence of the laser heating. It shows that the LIFT process is essentially driven by hydrodynamics and thermal transfer, and that a coupled approach including self-consistent laser energy deposition, heating by thermal conduction and specific models for matter is required.
- 2 July 2007
- Published by American Physical Society (APS) in Physical Review B
- Vol. 76 (2) , 024101
Model and numerical simulations of the propagation and absorption of a short laser pulse in a transparent dielectric material: Blast-wave launch and cavity formation
We present a theoretical model and its numerical realization, which describes a submicron cavity formation in a transparent dielectric under a tight focusing of a ultrashort laser pulse. The model contains two parts. The first one provides the laser energy deposition in the sample along with the energy balance—the reflection and transmission of the laser pulse. It resolves the full set of Maxwell’s equations in the two-dimensional geometry coupled to the material equations describing the atomic ionization by the laser electric field and the secondary electron collisions and the recombination processes. The second part describes the launch of the blast wave and the cavity formation under the deposited laser energy. The results of numerical simulations are compared with a qualitative theoretical model and experimental results.
- 2 July 2007
- Published by American Physical Society (APS) in Physical Review B
- Vol. 76 (2) , 024101
Model and numerical simulations of the propagation and absorption of a short laser pulse in a transparent dielectric material: Blast-wave launch and cavity formation
We present a theoretical model and its numerical realization, which describes a submicron cavity formation in a transparent dielectric under a tight focusing of a ultrashort laser pulse. The model contains two parts. The first one provides the laser energy deposition in the sample along with the energy balance—the reflection and transmission of the laser pulse. It resolves the full set of Maxwell’s equations in the two-dimensional geometry coupled to the material equations describing the atomic ionization by the laser electric field and the secondary electron collisions and the recombination processes. The second part describes the launch of the blast wave and the cavity formation under the deposited laser energy. The results of numerical simulations are compared with a qualitative theoretical model and experimental results.