Scott L. Delp
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Scott L. Delp has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Stephen J. Piazza
Biomechanics Laboratory, Department of Kinesiology, The Pennsylvania State University, University Park, PA 16802, USA
2 shared publications - Allison S. Arnold
Department of Mechanical Engineering, Stanford University, Stanford, CA 94305-5450, USA
1 shared publication - Cagatay Basdogan
College of Engineering, Koc University, Istanbul, Turkey
1 shared publication Joseph M. Rosen
Dartmouth-Hitchcock Medical Center, Lebanon, NH
1 shared publicationPeter Loan
MusculoGraphics, Inc., Evanston, IL
1 shared publicationS. David Stulberg
Department of Orthopaedics, Northwestern Memorial Hospital, Chicago, Illinois, U.S.A.
1 shared publication
Latest Publications
- 1 March 1998
- Published by Wiley in Journal of Orthopaedic Research
- Vol. 16 (2) , 264-270
Posterior tilting of the tibial component decreases femoral rollback in posterior‐substituting knee replacement: A computer simulation study
Posterior tilting of the tibial component is thought to increase the range of motion in posterior cruciate‐retaining total knee replacement, but its effect on implant motion in posterior cruciate‐substituting total knee replacement is unknown. This issue has become of interest recently because manufacturers have introduced instrumentation that produces a posteriorly tilted tibial cut for both implant types. The purpose of this study was to investigate how motion of posterior cruciate‐substituting total knee replacement is affected when the tibial component is installed with posterior tilt. Sagittal plane implant motions were predicted from prosthesis geometry with use of a computer simulation in which the femoral condyles were assumed to sit in the bottoms of the tibial condylar wells when the knee was in extension. Rollback of the femoral component was produced by a cam‐spine mechanism at higher angles of flexion. The simulations revealed that even small degrees of posterior tilt reduced rollback by limiting the interaction between the cam and spine. Tilting the component posteriorly by 5° caused the cam to contact the spine at a knee flexion angle that was 18° higher than with the untilted component. The results suggest that posterior tilting of the tibial component in posterior cruciate‐substituting knee replacement may not produce the same beneficial effects that have been reported for the tilting of tibial components in posterior cruciate‐retaining knee replacement.
- 1 March 1998
- Published by Wiley in Journal of Orthopaedic Research
- Vol. 16 (2) , 264-270
Posterior tilting of the tibial component decreases femoral rollback in posterior‐substituting knee replacement: A computer simulation study
Posterior tilting of the tibial component is thought to increase the range of motion in posterior cruciate‐retaining total knee replacement, but its effect on implant motion in posterior cruciate‐substituting total knee replacement is unknown. This issue has become of interest recently because manufacturers have introduced instrumentation that produces a posteriorly tilted tibial cut for both implant types. The purpose of this study was to investigate how motion of posterior cruciate‐substituting total knee replacement is affected when the tibial component is installed with posterior tilt. Sagittal plane implant motions were predicted from prosthesis geometry with use of a computer simulation in which the femoral condyles were assumed to sit in the bottoms of the tibial condylar wells when the knee was in extension. Rollback of the femoral component was produced by a cam‐spine mechanism at higher angles of flexion. The simulations revealed that even small degrees of posterior tilt reduced rollback by limiting the interaction between the cam and spine. Tilting the component posteriorly by 5° caused the cam to contact the spine at a knee flexion angle that was 18° higher than with the untilted component. The results suggest that posterior tilting of the tibial component in posterior cruciate‐substituting knee replacement may not produce the same beneficial effects that have been reported for the tilting of tibial components in posterior cruciate‐retaining knee replacement.
- 1 April 1997
- Published by MIT Press in PRESENCE: Virtual and Augmented Reality
- Vol. 6 (2) , 147-159
Surgical Simulation: An Emerging Technology for Training in Emergency Medicine
The current methods of training medical personnel to provide emergency medical care have several important shortcomings. For example, in the training of wound debridement techniques, animal models are used to gain experience treating traumatic injuries. We propose an alternative approach by creating a three-dimensional, interactive computer model of the human body that can be used within a virtual environment to learn and practice wound debridement techniques and Advanced Trauma Life Support (ATLS) procedures. As a first step, we have developed a computer model that represents the anatomy and physiology of a normal and injured lower limb. When visualized and manipulated in a virtual environment, this computer model will reduce the need for animals in the training of trauma management and potentially provide a superior training experience. This article describes the development choices that were made in implementing the preliminary system and the challenges that must be met to create an effective medical training environment.
- 1 April 1997
- Published by MIT Press in PRESENCE: Virtual and Augmented Reality
- Vol. 6 (2) , 147-159
Surgical Simulation: An Emerging Technology for Training in Emergency Medicine
The current methods of training medical personnel to provide emergency medical care have several important shortcomings. For example, in the training of wound debridement techniques, animal models are used to gain experience treating traumatic injuries. We propose an alternative approach by creating a three-dimensional, interactive computer model of the human body that can be used within a virtual environment to learn and practice wound debridement techniques and Advanced Trauma Life Support (ATLS) procedures. As a first step, we have developed a computer model that represents the anatomy and physiology of a normal and injured lower limb. When visualized and manipulated in a virtual environment, this computer model will reduce the need for animals in the training of trauma management and potentially provide a superior training experience. This article describes the development choices that were made in implementing the preliminary system and the challenges that must be met to create an effective medical training environment.