Tammy M. Cleek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tammy M. Cleek has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Karen J. Reynolds
Medical Device Research Institute, College of Science and Engineering Flinders University Adelaide South Australia Australia
2 shared publications - Aaron A. Mohtar
Medical Device Research Institute, School of Computer Science, Engineering and Mathematics, Flinders University, GPO Box 2100, Adelaide, South Australia 5001, Australia
1 shared publication Robert T. Whalen
1 shared publicationTrevor C Hearn
From the *School of Informatics and Engineering, Flinders University, Adelaide, Australia; and †Department of Orthopaedic Surgery, Flinders University, Adelaide, Australia
1 shared publication- Trevor C. Hearn
Orthopaedic Research Unit, Repatriation General Hospital, Flinders Medical Research Institute, Daws Road, Daw Park, Adelaide, South Australia 5041, Australia
1 shared publication
Latest Publications
- 1 April 2013
- Published by Elsevier in Journal of Biomechanics
- Vol. 46 (6) , 1207-1210
Predicting cancellous bone failure during screw insertion
- 1 April 2013
- Published by Elsevier in Journal of Biomechanics
- Vol. 46 (6) , 1207-1210
Predicting cancellous bone failure during screw insertion
- 1 February 2007
- Published by Wolters Kluwer Health in Journal of Orthopaedic Trauma
- Vol. 21 (2) , 117-123
Effect of Screw Torque Level on Cortical Bone Pullout Strength
Objectives: The objectives of this study were 2-fold: (1) to perform detailed analysis of cortical screw tightening stiffness during automated insertion, and (2) to determine the effect of 3 torque levels on the holding strength of the bone surrounding the screw threads as assessed by screw pullout. Methods: Ten pairs of ovine tibiae were used with 3 test sites spaced 20 mm apart centered along the shaft. One side of each pair was used for measuring ultimate failure torque (Tmax). These Tmax and bone-density values were used to predict Tmax at contralateral tibia sites. Screws were inserted and tightened to 50%, 70%, and 90% of predicted Tmax at the contralateral sites to encompass the average clinical level of torque (86% Tmax). Pullout tests were performed and maximum force values were normalized by cortical thickness. Results: Torque to failure tests indicated tightening to 86% Tmax occurs after yield and leads to an average 51% loss in stiffness. Normalized pullout strength for screws tightened to 50% Tmax, 70% Tmax, and 90% Tmax were 2525 ± 244, 2707 ± 280, and 2344 ± 346 N, respectively, with a significant difference between 70% Tmax and 90% Tmax groups (P < 0.05). Conclusions: Within the limitations of our study involving the testing of 1 type of screw purchase in ovine tibiae, results demonstrate that clinical levels of lag screw tightening (86% Tmax) are past the yield point of bone. Tightening to these high torque levels can cause damage leading to compromised holding strength. Further research is still required to establish the appropriate level of torque required for achieving optimal fracture fixation and healing.
- 1 February 2007
- Published by Wolters Kluwer Health in Journal of Orthopaedic Trauma
- Vol. 21 (2) , 117-123
Effect of Screw Torque Level on Cortical Bone Pullout Strength
Objectives: The objectives of this study were 2-fold: (1) to perform detailed analysis of cortical screw tightening stiffness during automated insertion, and (2) to determine the effect of 3 torque levels on the holding strength of the bone surrounding the screw threads as assessed by screw pullout. Methods: Ten pairs of ovine tibiae were used with 3 test sites spaced 20 mm apart centered along the shaft. One side of each pair was used for measuring ultimate failure torque (Tmax). These Tmax and bone-density values were used to predict Tmax at contralateral tibia sites. Screws were inserted and tightened to 50%, 70%, and 90% of predicted Tmax at the contralateral sites to encompass the average clinical level of torque (86% Tmax). Pullout tests were performed and maximum force values were normalized by cortical thickness. Results: Torque to failure tests indicated tightening to 86% Tmax occurs after yield and leads to an average 51% loss in stiffness. Normalized pullout strength for screws tightened to 50% Tmax, 70% Tmax, and 90% Tmax were 2525 ± 244, 2707 ± 280, and 2344 ± 346 N, respectively, with a significant difference between 70% Tmax and 90% Tmax groups (P < 0.05). Conclusions: Within the limitations of our study involving the testing of 1 type of screw purchase in ovine tibiae, results demonstrate that clinical levels of lag screw tightening (86% Tmax) are past the yield point of bone. Tightening to these high torque levels can cause damage leading to compromised holding strength. Further research is still required to establish the appropriate level of torque required for achieving optimal fracture fixation and healing.
- 1 October 2005
- Published by Wolters Kluwer Health in Medicine & Science in Sports & Exercise
- Vol. 37 (10) , 1806-1813
Effect of Activity and Age on Long Bones Using a New Densitometric Technique
Long bone structural parameters such as cross-sectional area or area moments of inertia are useful measures of long bone mechanical properties. We implemented a three-scan densitometric method to measure structural parameters in long bones of the lower leg in vivo. The validated method was applied to investigate the relationship between activity level, age, and long bone structural parameters in women. An aluminum phantom was used to estimate in vivo setup accuracy. In vivo precision was determined by same-day repeated measures on human subjects. For the activity study, women were recruited in two age groups (25–35, 60+yr) and two activity levels (recreational runners, nonrunners). Scans were taken of the middle third of the lower right leg; structural parameters for the tibia and fibula were determined at each scan line, averaged over the section, and adjusted by factors accounting for body size variations. Aluminum phantom cross-sectional area was underestimated by 4–6%, principal moments were underestimated by <5%, and principal angles were within ±1.2°. In vivo precision results (lower energy, scans spanning 60°) indicated coefficients of variation for cross-sectional area (A), principal moments of inertia (Imax, Imin), and polar moment of inertia (J) of 0.52, 5.87, 2.22, and 3.82%, respectively. The activity study showed mean adjusted tibial A, Imax, Imin, and J were significantly higher in runners compared with nonrunners. There was no dependence on age. A three-scan densitometric method for measuring cross-sectional structural parameters in long bones in vivo was validated; accuracy and precision measurements establishes confidence limits. From the activity study results, we postulate that higher loads associated with running lead to increased cross-sectional parameters to support axial loads, bending, and torsion in the tibia.
- 1 October 2005
- Published by Wolters Kluwer Health in Medicine & Science in Sports & Exercise
- Vol. 37 (10) , 1806-1813
Effect of Activity and Age on Long Bones Using a New Densitometric Technique
Long bone structural parameters such as cross-sectional area or area moments of inertia are useful measures of long bone mechanical properties. We implemented a three-scan densitometric method to measure structural parameters in long bones of the lower leg in vivo. The validated method was applied to investigate the relationship between activity level, age, and long bone structural parameters in women. An aluminum phantom was used to estimate in vivo setup accuracy. In vivo precision was determined by same-day repeated measures on human subjects. For the activity study, women were recruited in two age groups (25–35, 60+yr) and two activity levels (recreational runners, nonrunners). Scans were taken of the middle third of the lower right leg; structural parameters for the tibia and fibula were determined at each scan line, averaged over the section, and adjusted by factors accounting for body size variations. Aluminum phantom cross-sectional area was underestimated by 4–6%, principal moments were underestimated by <5%, and principal angles were within ±1.2°. In vivo precision results (lower energy, scans spanning 60°) indicated coefficients of variation for cross-sectional area (A), principal moments of inertia (Imax, Imin), and polar moment of inertia (J) of 0.52, 5.87, 2.22, and 3.82%, respectively. The activity study showed mean adjusted tibial A, Imax, Imin, and J were significantly higher in runners compared with nonrunners. There was no dependence on age. A three-scan densitometric method for measuring cross-sectional structural parameters in long bones in vivo was validated; accuracy and precision measurements establishes confidence limits. From the activity study results, we postulate that higher loads associated with running lead to increased cross-sectional parameters to support axial loads, bending, and torsion in the tibia.