Serdar Soyoz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Serdar Soyoz has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Maria. Q. Feng
Assistant Researcher, Dept. of Civil and Environmental Engineering, Univ. of California, Irvine, CA 92617
2 shared publications Maria Q. Feng
Department of Civil and Environmental Engineering, University of California, Irvine, CA, U.S.A.
1 shared publication- Masanobu Shinozuka
Postdoctoral Scholar, Department of Civil and Environmental Engineering, University of California, Irvine, CA 92697-2175
1 shared publication - Yangbo Chen
Engineer, Englekirk Partners Consulting Structural Engineers Inc., Los Angeles, CA 90018; formerly, Graduate Student, Dept. of Civil and Environmental Engineering, Univ. of California, Irvine, CA 92697-2175
1 shared publication
Latest Publications
- 1 January 2010
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 136 (1) , 100-106
Structural Reliability Estimation with Vibration-Based Identified Parameters
This paper presents a unique structural reliability estimation method incorporating structural parameter identification results based on the seismic response measurement. In the shaking table test, a three-bent concrete bridge model was shaken to different damage levels by a sequence of earthquake motions with increasing intensities. Structural parameters, stiffness and damping values of the bridge were identified under damaging seismic events based on the seismic response measurement. A methodology was developed to understand the importance of structural parameter identification in the reliability estimation. Along this line, a set of structural parameters were generated based on the Monte Carlo simulation. Each of them was assigned to the base bridge model. Then, every bridge model was analyzed using nonlinear time history analyses to obtain damage level at the specific locations. Last, reliability estimation was performed for bridges modeled with two sets of structural parameters. The first one was obt...
- 1 January 2010
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 136 (1) , 100-106
Structural Reliability Estimation with Vibration-Based Identified Parameters
This paper presents a unique structural reliability estimation method incorporating structural parameter identification results based on the seismic response measurement. In the shaking table test, a three-bent concrete bridge model was shaken to different damage levels by a sequence of earthquake motions with increasing intensities. Structural parameters, stiffness and damping values of the bridge were identified under damaging seismic events based on the seismic response measurement. A methodology was developed to understand the importance of structural parameter identification in the reliability estimation. Along this line, a set of structural parameters were generated based on the Monte Carlo simulation. Each of them was assigned to the base bridge model. Then, every bridge model was analyzed using nonlinear time history analyses to obtain damage level at the specific locations. Last, reliability estimation was performed for bridges modeled with two sets of structural parameters. The first one was obt...
- 1 July 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 134 (7) , 1235-1245
Large-Scale Shake Table Test Verification of Bridge Condition Assessment Methods
Methods that identify structural component stiffness degradation by pre- and postevent low amplitude vibration measurements, based on a linear time-invariant (LTI) system model, are conceptually justified by examining the hysteresis loops the structural components experience in such vibrations. Two large-scale shake table experiments, one on a two-column reinforced concrete (RC) bridge bent specimen, and the other on a two-span three-bent RC bridge specimen were performed, in which specimens were subjected to earthquake ground motions with increasing amplitude and progressively damaged. In each of the damaged stages between two strong motions, low amplitude vibrations of the specimens were aroused, and the postevent component stiffness coefficients were identified by optimizing the parameters in a LTI model. The stiffness degradation identified is consistent with the experimental hysteresis, and could be quantitatively related to the capacity residual of the components.
- 1 July 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 134 (7) , 1235-1245
Large-Scale Shake Table Test Verification of Bridge Condition Assessment Methods
Methods that identify structural component stiffness degradation by pre- and postevent low amplitude vibration measurements, based on a linear time-invariant (LTI) system model, are conceptually justified by examining the hysteresis loops the structural components experience in such vibrations. Two large-scale shake table experiments, one on a two-column reinforced concrete (RC) bridge bent specimen, and the other on a two-span three-bent RC bridge specimen were performed, in which specimens were subjected to earthquake ground motions with increasing amplitude and progressively damaged. In each of the damaged stages between two strong motions, low amplitude vibrations of the specimens were aroused, and the postevent component stiffness coefficients were identified by optimizing the parameters in a LTI model. The stiffness degradation identified is consistent with the experimental hysteresis, and could be quantitatively related to the capacity residual of the components.
- 23 October 2007
- Published by Hindawi Limited in Structural Control and Health Monitoring
- Vol. 15 (7) , 958-973
Instantaneous damage detection of bridge structures and experimental verification
An extended Kalman filtering (EKF) method was developed and applied to instantaneously identify elemental stiffness values of a structure during damaging seismic events based on vibration measurement. This method is capable of dealing with nonlinear as well as linear structural responses. Identification of the structural elemental stiffness enables location as well as quantification of structural damage. The instantaneous stiffness values during an event can provide highly useful information for post-event capacity estimation. In this study, a large-scale shaking table test of a three-bent concrete bridge model was performed in order to verify the proposed damage detection method. The bridge model was shaken to different damage levels by a sequence of earthquake motions with increasing intensities. The elemental stiffness values of the structure were instantaneously identified in real time during the damaging earthquake excitations using the EKF method. The identified stiffness degradations and their locations agreed well with the structural damage observed by visual inspection and strain measurements. More importantly, the seismic response accelerations analytically simulated using the instantaneous stiffness values thus identified agreed well with the measured accelerations, demonstrating the accuracy of the identified stiffness. This study presents an experimental verification of a structural damage detection method using a realistic bridge model subjected to realistic seismic damage. Copyright © 2007 John Wiley & Sons, Ltd.
- 23 October 2007
- Published by Hindawi Limited in Structural Control and Health Monitoring
- Vol. 15 (7) , 958-973
Instantaneous damage detection of bridge structures and experimental verification
An extended Kalman filtering (EKF) method was developed and applied to instantaneously identify elemental stiffness values of a structure during damaging seismic events based on vibration measurement. This method is capable of dealing with nonlinear as well as linear structural responses. Identification of the structural elemental stiffness enables location as well as quantification of structural damage. The instantaneous stiffness values during an event can provide highly useful information for post-event capacity estimation. In this study, a large-scale shaking table test of a three-bent concrete bridge model was performed in order to verify the proposed damage detection method. The bridge model was shaken to different damage levels by a sequence of earthquake motions with increasing intensities. The elemental stiffness values of the structure were instantaneously identified in real time during the damaging earthquake excitations using the EKF method. The identified stiffness degradations and their locations agreed well with the structural damage observed by visual inspection and strain measurements. More importantly, the seismic response accelerations analytically simulated using the instantaneous stiffness values thus identified agreed well with the measured accelerations, demonstrating the accuracy of the identified stiffness. This study presents an experimental verification of a structural damage detection method using a realistic bridge model subjected to realistic seismic damage. Copyright © 2007 John Wiley & Sons, Ltd.