DXDinghan Xiang

Dinghan Xiang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dinghan Xiang has a total of 5 co-authors. Here are the top co-authors by number of shared publications:

  • Ke Li

    College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

    2 shared publications
  • Kemei Tao

    College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, People's Republic of China

    1 shared publication
  • Weicai Shu

    College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, 29 Yudao Street, Nanjing 210016, People’s Republic of China

    1 shared publication
  • Xiaoyu Lei

    College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

    1 shared publication
  • Zhong Xu

    College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, 29 Yudao Street, Nanjing 210016, People’s Republic of China

    1 shared publication

Latest Publications

  • Green and self‐lubricating polyoxymethylene composites filled with low‐density polyethylene and rice husk flour

    by Ke Li, Dinghan Xiang, Xiaoyu Lei

    Polyoxymethylene (POM) composites filled with low‐density polyethylene (LDPE) and rice husk flour (RHF) were prepared by injection molding. The POM/5 wt % LDPE/7.5 wt % RHF composite exhibited the lowest wear rate, whereas the coefficient of friction remained low, and the POM/5 wt % LDPE/5 wt % RHF composite had the best mechanical properties. X‐ray diffraction analysis was carried out, and the worn surfaces were examined with scanning electron microscopy. The results showed that the addition of the filler reduced the crystallinity degree of the POM composites. The main wear mechanism for unfilled POM was adhesion, whereas for the POM composites, wear seemed to occur mainly by fatigue and abrasion. It was experimentally confirmed that the POM composite filled with LDPE and RHF, which is well‐performing, low‐cost, and environmentally friendly, could be a potential material for tribological applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008


  • On the Tribological Properties of PTFE Filled with Alumina Nanoparticles and Graphite

    by Dinghan Xiang, Ke Li, Weicai Shu, Zhong Xu

    Methods used to reinforce self-lubricating polymers generally also cause a significant increase in coefficient of friction, so that a trade-off must be made between coefficient of friction and wear resistance. Polytetrafluoroethylene (PTFE) composites filled with alumina nanoparticles and graphite were prepared by compression molding. Friction and wear experiments were carried out in a reciprocating sliding tribotester at a reciprocating frequency of 1.0 Hz, contact pressure of 5.0 MPa and relative humidity of (75 3)%. The nanocomposites slid against a 45 carbon steel track. Results showed that PTFE + 15 wt% alumina + 5 wt% graphite composite (D) exhibited a coefficient of steady-state friction lower than PTFE + 15 wt% alumina composite (B), while wear resistance of composite D is higher than composite B, and by about 200 times higher than unfilled PTFE. This behavior originates from the effective lubrication of graphite that possesses an extremely low coefficient of friction under the high humidity condition.


  • The mechanical and tribological properties of PTFE filled with PTFE waste powders

    by Dinghan Xiang, Kemei Tao

    Polytetrafluoroethylene (PTFE) composites filled with PTFE waste offer interesting combination of tribological properties and low cost. PTFE composites waste was mechanically cut and sieved into powders. PTFE composites filled with PTFE waste powders were prepared by compression molding. Friction and wear experiments were carried out in a reciprocating sliding tribotester at a reciprocating frequency of 1.0 Hz, a contact pressure of 5.5 MPa, and a relative humidity of (60 ± 5)%. PTFE materials slid against a 45 carbon steel track. Results showed that a PTFE composite (B) filled with 20 wt % PTFE waste exhibited a coefficient of steady‐state friction slightly higher than that of unfilled PTFE (A), while wear resistance over two orders of magnitude higher than that of unfilled PTFE (A). Another PTFE composite filled with PTFE waste and alumina nanoparticles exhibited the highest wear resistance among the three PTFE materials. This behavior originates from the effective reinforcement of PTFE waste as a filler. It was experimentally confirmed that the low cost recycling of PTFE waste without by‐products is feasible. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1035–1041, 2007