Takashi Jimbo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Takashi Jimbo has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Tetsuo Soga
Department of Electrical and Mechanical Engineering Nagoya Institute of Technology Gokiso‐cho, Showa‐Ku Nagoya 466‐8555 Japan
6 shared publications Xuemin Tian
Department of Environmental Technology and Urban Planning, Nagoya Institute of Technology
2 shared publicationsDebasish Ghosh
Department of Frontier Materials, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555, Japan
1 shared publicationDillip K. Mishra
Department of Environmental Technology and Urban Planning, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555, Japan
1 shared publicationDillip Kumar Mishra
Department of Environmental Technology and Urban Planning, Nagoya Institute of Technology
1 shared publicationHironori Taguchi
Department of Environmental Technology and Urban Planning, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555, Japan
1 shared publication
Latest Publications
- 1 February 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50 (2) , 020213
Simultaneous Formation of Both Single- and Multi-Wall Carbon Nanotubes by Ultrasonic Spray Pyrolysis
In this paper, we report the simultaneous formation of both single-walled carbon nanotubes (SWCNTs) and multi-wall carbon nanotubes (MWCNTs) in a reactor by ultrasonic spray pyrolysis. MWCNTs were formed at the center of the tube since catalyst particles accumulated on the substrates at the center agglomerate into a larger size. However, SWCNTs were formed downstream of the tube on desired substrates. Light transmission of the fluorine-doped tin oxide (FTO) substrate is reduced after SWCNT formation but returns to its initial state after ozone treatment.
- 1 February 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50 (2) , 020213
Simultaneous Formation of Both Single- and Multi-Wall Carbon Nanotubes by Ultrasonic Spray Pyrolysis
In this paper, we report the simultaneous formation of both single-walled carbon nanotubes (SWCNTs) and multi-wall carbon nanotubes (MWCNTs) in a reactor by ultrasonic spray pyrolysis. MWCNTs were formed at the center of the tube since catalyst particles accumulated on the substrates at the center agglomerate into a larger size. However, SWCNTs were formed downstream of the tube on desired substrates. Light transmission of the fluorine-doped tin oxide (FTO) substrate is reduced after SWCNT formation but returns to its initial state after ozone treatment.
- 1 January 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50 (1) , 01AF09
Improvement in Field Electron Emission Performance of Natural-Precursor-Grown Carbon Nanofibers by Thermal Annealing in Argon Atmosphere
Carbon nanofibers (CNFs) were grown on a graphite substrate by the spray pyrolysis of a botanical hydrocarbon, turpentine oil, using ferrocene as the catalyst and sulfur as the promoter. The as-grown CNFs were annealed at 450 °C for 30 min in an air, and then at 1800 °C in an argon atmosphere for 2 h. The annealed CNFs have better degree of crystallinity and reduced number of defects compared with the as-grown CNFs confirmed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, and thermogravimetric analysis. The as-grown and annealed CNFs were found to be effective electron emitters with turn-on fields of 3.2 and 2.1 V/µm, respectively. The improvement in field emission (FE) performance can be explained in terms of the higher degree of graphitization of the CNFs after thermal annealing. This improved FE performance of the natural precursor grown CNFs was comparable to the FE performance level attainable for the conventional carbon nanomaterials grown using petroleum products. Thus, it was considered that the use of petroleum products could be avoidable for CNF growth and that CNFs grown using ecofriendly materials are very promising for the application in future field emission displays (FEDs).
- 1 January 2011
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 50 (1) , 01AF09
Improvement in Field Electron Emission Performance of Natural-Precursor-Grown Carbon Nanofibers by Thermal Annealing in Argon Atmosphere
Carbon nanofibers (CNFs) were grown on a graphite substrate by the spray pyrolysis of a botanical hydrocarbon, turpentine oil, using ferrocene as the catalyst and sulfur as the promoter. The as-grown CNFs were annealed at 450 °C for 30 min in an air, and then at 1800 °C in an argon atmosphere for 2 h. The annealed CNFs have better degree of crystallinity and reduced number of defects compared with the as-grown CNFs confirmed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, and thermogravimetric analysis. The as-grown and annealed CNFs were found to be effective electron emitters with turn-on fields of 3.2 and 2.1 V/µm, respectively. The improvement in field emission (FE) performance can be explained in terms of the higher degree of graphitization of the CNFs after thermal annealing. This improved FE performance of the natural precursor grown CNFs was comparable to the FE performance level attainable for the conventional carbon nanomaterials grown using petroleum products. Thus, it was considered that the use of petroleum products could be avoidable for CNF growth and that CNFs grown using ecofriendly materials are very promising for the application in future field emission displays (FEDs).
- Open Access
- 31 January 2005
- Published by Taylor & Francis in Science and Technology of Advanced Materials
- Vol. 6 (1) , 27-33
Development of new materials for solar cells in Nagoya Institute of Technology
Solar cells with high efficiency and low price have long been desired, however, the commercially available solar cells are still expensive and the efficiencies of them are not high enough yet. A tandem solar cell was fabricated to develop a high-efficiency solar cell, and amorphous carbon solar cells were fabricated to develop a low-price solar cell. An AlGaAs/Si tandem solar cell was successfully fabricated by heteroepitaxial growth of AlGaAs on Si substrate. At first, a p–n junction was formed in Si substrate by the impurity diffusion method. Then, an AlGaAs p–n junction was grown by MOCVD. Since the AlGaAs p–n junction has a graded band gap emitter, the photo-excited minority carriers can be collected efficiently. The energy conversion efficiency of AlGaAs/Si tandem solar cell was 21.4% (AM0) in spite of large lattice mismatch and difference in thermal expansion coefficients between AlGaAs and Si. Solar cells were fabricated by using amorphous carbon films deposited by Ion Beam Sputtering and Pulse Laser Deposition(PLD). The highest efficiency of 1.82% (AM0) was attained with a-C(IBS)/p-C(pyrolysis)/p-Si structure. Solar cells using a-C:H were also fabricated by PLD and Plasma CVD, and the efficiencies of them were 2.1% (AM1.5) and 0.04% (AM0), respectively. Other research activities on solar cells in Nagoya Institute of Technology are briefly mentioned.
- 31 January 2005
- Published by Taylor & Francis in Science and Technology of Advanced Materials
- Vol. 6 (1) , 27-33
Open AccessDevelopment of new materials for solar cells in Nagoya Institute of Technology
Solar cells with high efficiency and low price have long been desired, however, the commercially available solar cells are still expensive and the efficiencies of them are not high enough yet. A tandem solar cell was fabricated to develop a high-efficiency solar cell, and amorphous carbon solar cells were fabricated to develop a low-price solar cell. An AlGaAs/Si tandem solar cell was successfully fabricated by heteroepitaxial growth of AlGaAs on Si substrate. At first, a p–n junction was formed in Si substrate by the impurity diffusion method. Then, an AlGaAs p–n junction was grown by MOCVD. Since the AlGaAs p–n junction has a graded band gap emitter, the photo-excited minority carriers can be collected efficiently. The energy conversion efficiency of AlGaAs/Si tandem solar cell was 21.4% (AM0) in spite of large lattice mismatch and difference in thermal expansion coefficients between AlGaAs and Si. Solar cells were fabricated by using amorphous carbon films deposited by Ion Beam Sputtering and Pulse Laser Deposition(PLD). The highest efficiency of 1.82% (AM0) was attained with a-C(IBS)/p-C(pyrolysis)/p-Si structure. Solar cells using a-C:H were also fabricated by PLD and Plasma CVD, and the efficiencies of them were 2.1% (AM1.5) and 0.04% (AM0), respectively. Other research activities on solar cells in Nagoya Institute of Technology are briefly mentioned.
- 1 January 2004
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Sensors and Micromachines
- Vol. 124 (2) , 54-58
The Deposition of a-C:H Films by Pulsed Laser Ablation
A new technique has been introduced to deposit amorphous hydrogenated carbon films (a-C:H) by pulsed laser deposition (PLD). Camphor, a natural source, has played a crucial role for the evolution of the film from amorphous carbon (a-C) to amorphous hydrogenated carbon (a-C:H). This has been confirmed by the presence of C-H stretching bond observed in the FTIR absorption spectra. The influence of camphor incorporation to the optical, electrical, and structural properties of the carbon film has been investigated by UV-visible spectroscopy, FTIR spectroscopy, Hall measurement, and Raman shift. As a kind of photo detectors, a solar cell with a-C:H/p-Si structure has been fabricated, its current-voltage (I-V) characteristics and spectral response are also studied. From the measurement of quantum efficiency, we find that the light sensing property of the new type of a-C:H film have been improved notably. In the short-wavelength region, the a-C:H layer contributes a maximum quantum efficiency as high as 30% despite the light loss by the surface electrode.
- 1 January 2004
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Sensors and Micromachines
- Vol. 124 (2) , 54-58
The Deposition of a-C:H Films by Pulsed Laser Ablation
A new technique has been introduced to deposit amorphous hydrogenated carbon films (a-C:H) by pulsed laser deposition (PLD). Camphor, a natural source, has played a crucial role for the evolution of the film from amorphous carbon (a-C) to amorphous hydrogenated carbon (a-C:H). This has been confirmed by the presence of C-H stretching bond observed in the FTIR absorption spectra. The influence of camphor incorporation to the optical, electrical, and structural properties of the carbon film has been investigated by UV-visible spectroscopy, FTIR spectroscopy, Hall measurement, and Raman shift. As a kind of photo detectors, a solar cell with a-C:H/p-Si structure has been fabricated, its current-voltage (I-V) characteristics and spectral response are also studied. From the measurement of quantum efficiency, we find that the light sensing property of the new type of a-C:H film have been improved notably. In the short-wavelength region, the a-C:H layer contributes a maximum quantum efficiency as high as 30% despite the light loss by the surface electrode.
- 1 December 2003
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 42 (Part 2, No) , L1419-L1421
Fabrication of GaAs/Si Tandem Solar Cell by Epitaxial Lift-Off Technique
A GaAs solar cell was successfully transplanted from a GaAs substrate to a Si substrate without degrading the conversion efficiency. The conversion efficiency of the GaAs solar cell bonded to the Si substrate is almost the same as that of the cell grown on a GaAs substrate and is much superior to that of the cell grown on a Si substrate by heteroepitaxy. The GaAs/Si tandem solar cell with the conversion efficiency of 19.4% (top cell: 18.2%, bottom cell: 1.2%) has been demonstrated.
- 1 December 2003
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 42 (Part 2, No) , L1419-L1421
Fabrication of GaAs/Si Tandem Solar Cell by Epitaxial Lift-Off Technique
A GaAs solar cell was successfully transplanted from a GaAs substrate to a Si substrate without degrading the conversion efficiency. The conversion efficiency of the GaAs solar cell bonded to the Si substrate is almost the same as that of the cell grown on a GaAs substrate and is much superior to that of the cell grown on a Si substrate by heteroepitaxy. The GaAs/Si tandem solar cell with the conversion efficiency of 19.4% (top cell: 18.2%, bottom cell: 1.2%) has been demonstrated.
- 1 October 2003
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 42 (Part 2, No) , L1164-L1166
Diamond Synthesized at Room Temperature by Pulsed Laser Deposition in Vacuum
Here we show that diamond particles were formed on (100) silicon substrates by XeCl (308 nm, 20 ns) laser ablation using a urea doped camphoric carbon target in vacuum. The substrate temperature and the pressure were kept at room temperature (25°C) and (4–5)×10-5 Torr, respectively without feeding any gases during the deposition. Raman spectroscopy analysis confirmed the diamond cubic structure of the crystals by the presence of a sharp peak at 1337.8 cm-1. One broad peak is also observed in the spectra centered at 1550 cm-1, which is attributed to the G-peak in the film.
- 1 October 2003
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 42 (Part 2, No) , L1164-L1166
Diamond Synthesized at Room Temperature by Pulsed Laser Deposition in Vacuum
Here we show that diamond particles were formed on (100) silicon substrates by XeCl (308 nm, 20 ns) laser ablation using a urea doped camphoric carbon target in vacuum. The substrate temperature and the pressure were kept at room temperature (25°C) and (4–5)×10-5 Torr, respectively without feeding any gases during the deposition. Raman spectroscopy analysis confirmed the diamond cubic structure of the crystals by the presence of a sharp peak at 1337.8 cm-1. One broad peak is also observed in the spectra centered at 1550 cm-1, which is attributed to the G-peak in the film.