Philippe Bolon
Philippe Bolon has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Mihai Ciuc
2 shared publications- Andreea Julea
European Commission, Joint Research Centre (JRC), Ispra, Italy
1 shared publication - Emmanuel Trouve
Laboratoire d'Informatique, Systèmes, Traitement de l'Information et de la Connaissance, Université de Savoie–Polytech Annecy-Chambéry, Annecy-le-Vieux Cedex, France
1 shared publication Emmanuel Trouvé
1 shared publicationEmmanuele Trouve
Ecole Superieure d'Ingeniers d'Anne (France)
1 shared publicationHerve Trebossen
Univ. de Marne la Vallee (France)
1 shared publication
Latest Publications
- 20 November 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Geoscience and Remote Sensing Letters
- Vol. 7 (2) , 309-313
Radar-Coding and Geocoding Lookup Tables for the Fusion of GIS and SAR Data in Mountain Areas
Synthetic aperture radar (SAR) image orthorectification induces an important alteration of information due to the side-looking geometry of SAR acquisition. In high-relief areas, the difficulty is increased by the foldover effect: The images acquired with low incidence angles cannot be registered by a bijective transformation like polynomial transformations, as usually proposed by conventional software. In this letter, a simple and efficient method, fitted to geocoded data and SAR images, is introduced to propose a generic coregistration tool that takes SAR geometry into account without requiring the exact sensor model, specific parameters, and precise navigation data. This method is based on a simulated SAR image and on the computation of lookup tables (LUTs) that represent the coordinate transform from one geometry to the other. Results are presented on a high-relief area in the Alps, where satellite and airborne SAR images are used for glacier evolution monitoring. A comparison to other sensor-independent approaches has been performed, showing that the proposed approach performs better in mountain areas. The resulting LUTs allow merging SAR data with the georeferenced data, either in ground geometry by orthorectifying the SAR information or in radar geometry by the inverse transformation, namely, radar-coding data from a geographic information system, to improve the analysis of SAR images and the result interpretation.
- 20 November 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Geoscience and Remote Sensing Letters
- Vol. 7 (2) , 309-313
Radar-Coding and Geocoding Lookup Tables for the Fusion of GIS and SAR Data in Mountain Areas
Synthetic aperture radar (SAR) image orthorectification induces an important alteration of information due to the side-looking geometry of SAR acquisition. In high-relief areas, the difficulty is increased by the foldover effect: The images acquired with low incidence angles cannot be registered by a bijective transformation like polynomial transformations, as usually proposed by conventional software. In this letter, a simple and efficient method, fitted to geocoded data and SAR images, is introduced to propose a generic coregistration tool that takes SAR geometry into account without requiring the exact sensor model, specific parameters, and precise navigation data. This method is based on a simulated SAR image and on the computation of lookup tables (LUTs) that represent the coordinate transform from one geometry to the other. Results are presented on a high-relief area in the Alps, where satellite and airborne SAR images are used for glacier evolution monitoring. A comparison to other sensor-independent approaches has been performed, showing that the proposed approach performs better in mountain areas. The resulting LUTs allow merging SAR data with the georeferenced data, either in ground geometry by orthorectifying the SAR information or in radar geometry by the inverse transformation, namely, radar-coding data from a geographic information system, to improve the analysis of SAR images and the result interpretation.
- 10 November 2001
- Published by Optica Publishing Group in Applied Optics
- Vol. 40 (32) , 5954-5966
Adaptive-neighborhood speckle removal in multitemporal synthetic aperture radar images
We present a new method for multitemporal synthetic aperture radar image filtering using three-dimensional (3D) adaptive neighborhoods. The method takes both spatial and temporal information into account to derive the speckle-free value of a pixel. For each pixel individually, a 3D adaptive neighborhood is determined that contains only pixels belonging to the same distribution as the current pixel. Then statistics computed inside the established neighborhood are used to derive the filter output. It is shown that the method provides good results by drastically reducing speckle over homogeneous areas while retaining edges and thin structures. The performances of the proposed method are compared in terms of subjective and objective measures with those given by several classical speckle-filtering methods.
- 10 November 2001
- Published by Optica Publishing Group in Applied Optics
- Vol. 40 (32) , 5954-5966
Adaptive-neighborhood speckle removal in multitemporal synthetic aperture radar images
We present a new method for multitemporal synthetic aperture radar image filtering using three-dimensional (3D) adaptive neighborhoods. The method takes both spatial and temporal information into account to derive the speckle-free value of a pixel. For each pixel individually, a 3D adaptive neighborhood is determined that contains only pixels belonging to the same distribution as the current pixel. Then statistics computed inside the established neighborhood are used to derive the filter output. It is shown that the method provides good results by drastically reducing speckle over homogeneous areas while retaining edges and thin structures. The performances of the proposed method are compared in terms of subjective and objective measures with those given by several classical speckle-filtering methods.
- 19 January 2001
- Published by SPIE-Intl Soc Optical Eng
- Vol. 4170, 1-13
Multitemporal SAR image filtering using 3D adaptive neighborhoods
In this paper, we present a new method for multitemporal SAR image filtering using 3D adaptive neighborhoods. The method takes into account both spatial and temporal information to derive the speckle-free value of a pixel. For each pixel individually, a 3D adaptive neighborhood is determined to contain only pixels coming from the same distribution as the current one. Then statistics computed inside the established neighborhood are used to derive the filter output. It is shown that the method provides good results by drastically reducing speckle over homogeneous areas while retaining edges and thin structures. The performances of the proposed method are compared in terms of subjective and objective measures with those given by several classical speckle filtering methods.
- 19 January 2001
- Published by SPIE-Intl Soc Optical Eng
- Vol. 4170, 1-13
Multitemporal SAR image filtering using 3D adaptive neighborhoods
In this paper, we present a new method for multitemporal SAR image filtering using 3D adaptive neighborhoods. The method takes into account both spatial and temporal information to derive the speckle-free value of a pixel. For each pixel individually, a 3D adaptive neighborhood is determined to contain only pixels coming from the same distribution as the current one. Then statistics computed inside the established neighborhood are used to derive the filter output. It is shown that the method provides good results by drastically reducing speckle over homogeneous areas while retaining edges and thin structures. The performances of the proposed method are compared in terms of subjective and objective measures with those given by several classical speckle filtering methods.