Claus Thomy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Claus Thomy has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Frank Vollertsen
BIAS – Bremer Institut für angewandte Strahltechnik GmbH, Bremen, Germany
4 shared publications Andreas Wirth
1 shared publicationFelix Möller
1 shared publicationFlorian Wagner
1 shared publicationFrank Vollertsen
1 shared publication- Marius Gatzen
BIAS-Bremer Institut für Angewandte Strahltechnik GmbH, Klagenfurter Str. 5, 28359 Bremen, Germany
1 shared publication
Latest Publications
- Open Access
Experimental and Numerical Investigation of an Overheated Aluminum Droplet Wetting a Zinc-Coated Steel Surface
Wetting steel surfaces with liquid aluminum without the use of flux can be enabled by the presence of a zinc-coating. The mechanisms behind this effect are not yet fully understood. Research results on single aluminum droplets falling on commercial galvanized steel substrates revealed the good wetting capability of zinc coatings independently from the coating type. The final wetting angle and length are apparently linked to the time where zinc is liquefied during its contact with the overheated aluminum melt. This led to the assumption that the interaction is basically a fluid dynamic effect of liquid aluminum getting locally alloyed by zinc. A numerical model was developed to describe the transient behavior of droplet movement and mixing with the liquefied zinc layer to understand the spreading dynamics. The simulations reveal a displacement of the molten zinc after the impact of the droplet, which ultimately leads to an accumulation of zinc in the outer weld toe after solidification. The simulation approach neglects the effect of evaporating zinc, resulting in a slight overestimation of the final droplet width. However, in terms of spreading initiation during the first milliseconds, the simulation is in good correlation with experimental observations and demonstrates the reason for the good wetting in the presence of zinc coatings.
Open AccessExperimental and Numerical Investigation of an Overheated Aluminum Droplet Wetting a Zinc-Coated Steel Surface
Wetting steel surfaces with liquid aluminum without the use of flux can be enabled by the presence of a zinc-coating. The mechanisms behind this effect are not yet fully understood. Research results on single aluminum droplets falling on commercial galvanized steel substrates revealed the good wetting capability of zinc coatings independently from the coating type. The final wetting angle and length are apparently linked to the time where zinc is liquefied during its contact with the overheated aluminum melt. This led to the assumption that the interaction is basically a fluid dynamic effect of liquid aluminum getting locally alloyed by zinc. A numerical model was developed to describe the transient behavior of droplet movement and mixing with the liquefied zinc layer to understand the spreading dynamics. The simulations reveal a displacement of the molten zinc after the impact of the droplet, which ultimately leads to an accumulation of zinc in the outer weld toe after solidification. The simulation approach neglects the effect of evaporating zinc, resulting in a slight overestimation of the final droplet width. However, in terms of spreading initiation during the first milliseconds, the simulation is in good correlation with experimental observations and demonstrates the reason for the good wetting in the presence of zinc coatings.
- 1 May 2012
- Published by Springer Nature in Welding in the World
- Vol. 56 (5-6) , 124-132
Laser-Mig Hybrid Welding Of Aluminium To Steel — Effect Of Process Parameters On Joint Properties
- 1 May 2012
- Published by Springer Nature in Welding in the World
- Vol. 56 (5-6) , 124-132
Laser-Mig Hybrid Welding Of Aluminium To Steel — Effect Of Process Parameters On Joint Properties
- 1 January 2010
- Published by Laser Institute of America
- Vol. 2010 (1) , 85
Distortion effects in micro welding with fibre laser
While effects associated with distortion are already understood quite well in keyhole laser welding in the macro range, this is not yet the case for welding in the micro range. In special, the effect of sheet thickness on distortion in micro welding of aluminium sheets with single-mode fibre laser is of interest. To investigate this effect, linear bead-on-plate welds were carried out, whilst total nominal heat input was scaled with sheet thickness by scaling laser power. Distortion (out-of-plane) was measured using a laser triangulation sensor. To improve understanding of the effect of heat input and sheet thickness, a straightforward analytical model from thermal bending was modified and applied. It was found that average (out-of-plane) distortion will increase with decreasing sheet thickness, leading to a displacement out of plane of up to approximately double the sheet thickness. A simplistic model for buckling in thermal forming was applied and found to be in good correlation with the experimental data, giving a dependence of distortion on sheet thickness s0 according to approximately 1/s02/3.
- 1 January 2010
- Published by Laser Institute of America
- Vol. 2010 (1) , 85
Distortion effects in micro welding with fibre laser
While effects associated with distortion are already understood quite well in keyhole laser welding in the macro range, this is not yet the case for welding in the micro range. In special, the effect of sheet thickness on distortion in micro welding of aluminium sheets with single-mode fibre laser is of interest. To investigate this effect, linear bead-on-plate welds were carried out, whilst total nominal heat input was scaled with sheet thickness by scaling laser power. Distortion (out-of-plane) was measured using a laser triangulation sensor. To improve understanding of the effect of heat input and sheet thickness, a straightforward analytical model from thermal bending was modified and applied. It was found that average (out-of-plane) distortion will increase with decreasing sheet thickness, leading to a displacement out of plane of up to approximately double the sheet thickness. A simplistic model for buckling in thermal forming was applied and found to be in good correlation with the experimental data, giving a dependence of distortion on sheet thickness s0 according to approximately 1/s02/3.
- Open Access
- 7 September 2007
- Published by Wiley in PhotonicsViews
- Vol. 4 (4) , 36-40
Laser‐MIG‐Hybridfügen von Aluminium‐Stahl Leichtbaustrukturen
Im Fahrzeugbau wird derzeit der Einsatz von hybriden Strukturelementen aus artungleichen Werkstoffen intensiv diskutiert. Ziel ist es dabei, Gewichtsreduktionen zu erreichen und gleichzeitig die mechanischen Eigenschaften zu erhalten oder zu verbessern. Das Fügen von Aluminium‐ mit Stahl‐Legierungen ist dabei besonders interessant für den Fahrzeugbau, aber auch für den Schiffbau.
- 7 September 2007
- Published by Wiley in PhotonicsViews
- Vol. 4 (4) , 36-40
Open AccessLaser‐MIG‐Hybridfügen von Aluminium‐Stahl Leichtbaustrukturen
Im Fahrzeugbau wird derzeit der Einsatz von hybriden Strukturelementen aus artungleichen Werkstoffen intensiv diskutiert. Ziel ist es dabei, Gewichtsreduktionen zu erreichen und gleichzeitig die mechanischen Eigenschaften zu erhalten oder zu verbessern. Das Fügen von Aluminium‐ mit Stahl‐Legierungen ist dabei besonders interessant für den Fahrzeugbau, aber auch für den Schiffbau.
- 1 January 2007
- Published by Laser Institute of America
- Vol. 2007 (1) , 1608
Fibre laser GMA hybrid welding of thin sheet material
In order to restrain heat input and increase productivity in thin steel sheet welding compared to arc and laser welding processes, a laser GMA hybrid welding process with single-mode fibre laser was developed. The effects of some basic parameters such as laser power, focal position and laser arc distance were investigated and discussed in view of weld quality and process efficiency. Moreover, the influence of gap on weld quality, hardness and static strength was considered. Based on these studies, it was demonstrated under laboratory conditions that a gap bridging in the range of 50% of sheet thickness at high welding speeds may be feasible for thin sheet welding using this newly developed process.
- 1 January 2007
- Published by Laser Institute of America
- Vol. 2007 (1) , 1608
Fibre laser GMA hybrid welding of thin sheet material
In order to restrain heat input and increase productivity in thin steel sheet welding compared to arc and laser welding processes, a laser GMA hybrid welding process with single-mode fibre laser was developed. The effects of some basic parameters such as laser power, focal position and laser arc distance were investigated and discussed in view of weld quality and process efficiency. Moreover, the influence of gap on weld quality, hardness and static strength was considered. Based on these studies, it was demonstrated under laboratory conditions that a gap bridging in the range of 50% of sheet thickness at high welding speeds may be feasible for thin sheet welding using this newly developed process.