Jing-Chung Shen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jing-Chung Shen has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Chien-Hung Liu
Department of Mechanical Engineering, National Chung Hsing University, Taichung 40227, Taiwan
3 shared publications Chia-Hung Wu
2 shared publications- Wen-Yuh Jywe
Smart Machine and Intelligent Manufacturing research center, National Formosa University, Yunlin 632, Taiwan
2 shared publications Chau-Chia Yan
Department of Automation Engineering, National Formosa University, Yunlin County, Taiwan
1 shared publicationChien-Hung Liu
Department of Automation Engineering, National Formosa University Huwei, Yunlin, Taiwan
1 shared publicationChun-Jen Chen
National Cheng Kung University, Tainan, Taiwan, R.O.C.
1 shared publication
Latest Publications
- 1 April 2014
- Published by Elsevier in Precision Engineering
- Vol. 38 (2) , 391-397
Control of an equipment for fabricating periodic nanostructure
- 1 April 2014
- Published by Elsevier in Precision Engineering
- Vol. 38 (2) , 391-397
Control of an equipment for fabricating periodic nanostructure
- 20 June 2013
- Published by Springer Nature in Microsystem Technologies
- Vol. 19 (11) , 1731-1736
Tracking control of a precision stage with integral sliding-mode friction estimator
- 20 June 2013
- Published by Springer Nature in Microsystem Technologies
- Vol. 19 (11) , 1731-1736
Tracking control of a precision stage with integral sliding-mode friction estimator
- 15 April 2012
- Published by American Scientific Publishers in Advanced Science Letters
- Vol. 8 (1) , 327-331
Control of a Laser Direct Writing Equipment for Manufacturing Periodic Nano-Structure
- 15 April 2012
- Published by American Scientific Publishers in Advanced Science Letters
- Vol. 8 (1) , 327-331
Control of a Laser Direct Writing Equipment for Manufacturing Periodic Nano-Structure
- 1 January 2011
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 44 (1) , 3533-3538
Active Probe Control of a Metrological Atomic Force Microscopy
- 1 January 2011
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 44 (1) , 3533-3538
Active Probe Control of a Metrological Atomic Force Microscopy
- 1 May 2008
- Published by Wiley in Asian Journal of Control
- Vol. 10 (3) , 267-276
Sliding‐mode control of a three‐degrees‐of‐freedom nanopositioner
This paper presents the sliding‐mode control of a three‐degrees‐of‐freedom nanopositioner (Z, θx, θy). This nanopositioner is actuated by piezoelectric actuators. Capacitive gap sensors are used for position feedback. In order to design the feedback controller, the open‐loop characteristics of this nanopositioner are investigated. Based on the results of the investigation, each pair of piezoelectric actuators and corresponding gap sensors is treated as an independent system and modeled as a first‐order linear model coupled with hysteresis. When the model is identified and the hysteresis nonlinearity is linearized, a linear system model with uncertainty is used to design the controller. When designing the controller, the sliding‐mode disturbance (uncertainty) estimation and compensation scheme is used. The structure of the proposed controller is similar to that of a proportional integral derivative controller. Thus, it can be easily implemented. Experimental results show that 3‐nm tracking resolution can be obtained. Copyright © 2008 John Wiley and Sons Asia Pte Ltd and Chinese Automatic Control Society
- 1 May 2008
- Published by Wiley in Asian Journal of Control
- Vol. 10 (3) , 267-276
Sliding‐mode control of a three‐degrees‐of‐freedom nanopositioner
This paper presents the sliding‐mode control of a three‐degrees‐of‐freedom nanopositioner (Z, θx, θy). This nanopositioner is actuated by piezoelectric actuators. Capacitive gap sensors are used for position feedback. In order to design the feedback controller, the open‐loop characteristics of this nanopositioner are investigated. Based on the results of the investigation, each pair of piezoelectric actuators and corresponding gap sensors is treated as an independent system and modeled as a first‐order linear model coupled with hysteresis. When the model is identified and the hysteresis nonlinearity is linearized, a linear system model with uncertainty is used to design the controller. When designing the controller, the sliding‐mode disturbance (uncertainty) estimation and compensation scheme is used. The structure of the proposed controller is similar to that of a proportional integral derivative controller. Thus, it can be easily implemented. Experimental results show that 3‐nm tracking resolution can be obtained. Copyright © 2008 John Wiley and Sons Asia Pte Ltd and Chinese Automatic Control Society
- 1 January 2008
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 41 (2) , 11817-11822
Control of a Five-Degrees-of-Freedom Nanopositioner
- 1 January 2008
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 41 (2) , 11817-11822
Control of a Five-Degrees-of-Freedom Nanopositioner
- 1 January 2006
- Published by ASME International
- p. 997-1002
Development of a Laser Based Dual-Axial Five-Degrees-of-Freedom Measurement System for an X-Y Stage
This paper presents a new precision multi-DOF measurement system which has been developed and implemented for the simultaneous measurement of 5DOF motion errors (two linear positions, as well as pitch, roll and yaw) of an X-Y stage. In this paper, the 3DOF laser interferometer was produced by designing the optical path from the one-degrees-of-freedom laser interferometer. The system employs two three-degree-of-freedom interferometers to detect two position errors and three angular errors of the X-Y stage. The experimental setups and measuring procedure and a systematic calculated method for the error verification are presented in the paper. The resolution of measuring the angular errors component is about 0.055 arcsec.
- 1 January 2006
- Published by ASME International
- p. 997-1002
Development of a Laser Based Dual-Axial Five-Degrees-of-Freedom Measurement System for an X-Y Stage
This paper presents a new precision multi-DOF measurement system which has been developed and implemented for the simultaneous measurement of 5DOF motion errors (two linear positions, as well as pitch, roll and yaw) of an X-Y stage. In this paper, the 3DOF laser interferometer was produced by designing the optical path from the one-degrees-of-freedom laser interferometer. The system employs two three-degree-of-freedom interferometers to detect two position errors and three angular errors of the X-Y stage. The experimental setups and measuring procedure and a systematic calculated method for the error verification are presented in the paper. The resolution of measuring the angular errors component is about 0.055 arcsec.