Erhard Schafler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Erhard Schafler has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Florian Spieckermann
Department of Materials Science Montanuniversität Leoben Leoben 8700 Austria
5 shared publications - Michael J. Zehetbauer
Physics of Nanostructured Materials, Faculty of Physics, University of Vienna, Wien, Austria
5 shared publications - Michael Kerber
University of Vienna
4 shared publications - Harald Wilhelm
Research Group Physics of Nanostructured Materials, Faculty of Physics, University of Vienna, Boltzmanngasse 5, Wien, Austria
3 shared publications - Ádám Révész
Department of Materials Physics, Eötvös University, P.O. Box 32, H-1518 Budapest, Hungary
3 shared publications - Andrea Ojdanic
Physics of Nanostructured Materials, Faculty of Physics, University of Vienna, 1090 Vienna, Austria
2 shared publications
Latest Publications
- Open Access
- 1 August 2026
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 21
Analysis of microstructural evolution and mechanical properties of AZ80/TiO2 nanocomposite processed by high-pressure torsion
- 1 August 2026
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 21
Open AccessAnalysis of microstructural evolution and mechanical properties of AZ80/TiO2 nanocomposite processed by high-pressure torsion
- Open Access
- 30 June 2025
- Published by Wiley in Advanced Science
- Vol. 12 (33) , e07168
Achieving Complex Nanostructures: The Role of Hydrogen in Controlling Mechanical Alloying and Microstructure Evolution in the TiVZrNbHf‐Cu System
Hydrogen is key in reducing greenhouse gas emissions in materials production. At the same time, it significantly affects mechanical properties, often causing unwanted embrittlement. However, rather than solely addressing these disadvantages, hydrogen's inevitable role in sustainable metallurgy should be leveraged to create new and potentially superior materials. Here, it is shown that using hydrogen in the form of metal hydrides introduces a barrier to mechanical alloying, stabilizing otherwise unattainable microstructures. Severe plastic deformation of a composite of the equiatomic high entropy alloy (HEA) TiVZrNbHf and Cu leads to amorphization, while substituting the HEA with its hydride preserves the two‐phase structure. Monte Carlo simulations confirm that the significantly different hydrogen affinities, together with the restricted dislocation motion in the hydride, create a barrier to mechanical alloying. This hydride route could enable new microstructure states, even in well‐studied material systems. It opens an additional dimension in designing materials containing phases with diverging hydrogen affinities, offering tighter control over mechanical alloying.
- 30 June 2025
- Published by Wiley in Advanced Science
- Vol. 12 (33) , e07168
Open AccessAchieving Complex Nanostructures: The Role of Hydrogen in Controlling Mechanical Alloying and Microstructure Evolution in the TiVZrNbHf‐Cu System
Hydrogen is key in reducing greenhouse gas emissions in materials production. At the same time, it significantly affects mechanical properties, often causing unwanted embrittlement. However, rather than solely addressing these disadvantages, hydrogen's inevitable role in sustainable metallurgy should be leveraged to create new and potentially superior materials. Here, it is shown that using hydrogen in the form of metal hydrides introduces a barrier to mechanical alloying, stabilizing otherwise unattainable microstructures. Severe plastic deformation of a composite of the equiatomic high entropy alloy (HEA) TiVZrNbHf and Cu leads to amorphization, while substituting the HEA with its hydride preserves the two‐phase structure. Monte Carlo simulations confirm that the significantly different hydrogen affinities, together with the restricted dislocation motion in the hydride, create a barrier to mechanical alloying. This hydride route could enable new microstructure states, even in well‐studied material systems. It opens an additional dimension in designing materials containing phases with diverging hydrogen affinities, offering tighter control over mechanical alloying.
- Open Access
Shear Band-Induced Internal Surface Structures in a Vitreloy Bulk Metallic Glass Deformed by High-Pressure Torsion
In the present investigation, high stability Vitreloy Zr44Ti11Cu10Ni10Be25 bulk metallic glass has been subjected to severe shear deformation by high-pressure torsion for 0.1 revolutions under an applied pressure of 4 and 8 GPa. The fully glassy nature of the as-cast glass has been confirmed by X-ray powder diffraction and differential scanning calorimetry. Deformation-induced surface features on an internal plane of the deformed disk-shaped specimens were studied in detail at the macroscopic level by optical reconstruction method and at microscopic scales by white-light optical profilometry. Shear and compressive strain components were measured based on surface changes and it was determined that compressive strain gradient with 0.2–0.4 strain change builds up toward the disk edge, while only part of the nominal shear deformation occurs in the disk interior. The effect of strain localization in the Vitreloy bulk metallic glasses has been quantified by a surface distortion model based on simple shear. The model was then validated experimentally by the reconstructed z-profiles.
Open AccessShear Band-Induced Internal Surface Structures in a Vitreloy Bulk Metallic Glass Deformed by High-Pressure Torsion
In the present investigation, high stability Vitreloy Zr44Ti11Cu10Ni10Be25 bulk metallic glass has been subjected to severe shear deformation by high-pressure torsion for 0.1 revolutions under an applied pressure of 4 and 8 GPa. The fully glassy nature of the as-cast glass has been confirmed by X-ray powder diffraction and differential scanning calorimetry. Deformation-induced surface features on an internal plane of the deformed disk-shaped specimens were studied in detail at the macroscopic level by optical reconstruction method and at microscopic scales by white-light optical profilometry. Shear and compressive strain components were measured based on surface changes and it was determined that compressive strain gradient with 0.2–0.4 strain change builds up toward the disk edge, while only part of the nominal shear deformation occurs in the disk interior. The effect of strain localization in the Vitreloy bulk metallic glasses has been quantified by a surface distortion model based on simple shear. The model was then validated experimentally by the reconstructed z-profiles.
- Open Access
- 19 May 2023
- Published by Elsevier in Free Radical Biology and Medicine
- Vol. 201, 33
A new, radical insight into cytotoxicity of implant-intended biodegradable zinc
- 19 May 2023
- Published by Elsevier in Free Radical Biology and Medicine
- Vol. 201, 33
Open AccessA new, radical insight into cytotoxicity of implant-intended biodegradable zinc
- Open Access
Thermal, Microstructural and Electrochemical Hydriding Performance of a Mg65Ni20Cu5Y10 Metallic Glass Catalyzed by CNT and Processed by High-Pressure Torsion
A Mg65Ni20Cu5Y10 metallic glass was produced by melt spinning and was mixed with a 5 wt.% multiwall carbon nanotube additive in a high-energy ball mill. Subsequently, the composite mixture was exposed to high-pressure torsion deformation with different torsion numbers. Complimentary XRD and DSC experiments confirmed the exceptional structural and thermal stability of the amorphous phase against severe plastic deformation. Combined high-resolution transmission electron microscopy observations and fast Fourier transform analysis revealed deformation-induced Mg2Ni nanocrystals, together with the structural and morphological stability of the nanotubes. The electrochemical hydrogen discharge capacity of the severely deformed pure metallic glass was substantially lower than that of samples with the nanotube additive for several cycles. It was also established that the most deformed sample containing nanotubes exhibited a drastic breakdown in the electrochemical capacity after eight cycles.
Open AccessThermal, Microstructural and Electrochemical Hydriding Performance of a Mg65Ni20Cu5Y10 Metallic Glass Catalyzed by CNT and Processed by High-Pressure Torsion
A Mg65Ni20Cu5Y10 metallic glass was produced by melt spinning and was mixed with a 5 wt.% multiwall carbon nanotube additive in a high-energy ball mill. Subsequently, the composite mixture was exposed to high-pressure torsion deformation with different torsion numbers. Complimentary XRD and DSC experiments confirmed the exceptional structural and thermal stability of the amorphous phase against severe plastic deformation. Combined high-resolution transmission electron microscopy observations and fast Fourier transform analysis revealed deformation-induced Mg2Ni nanocrystals, together with the structural and morphological stability of the nanotubes. The electrochemical hydrogen discharge capacity of the severely deformed pure metallic glass was substantially lower than that of samples with the nanotube additive for several cycles. It was also established that the most deformed sample containing nanotubes exhibited a drastic breakdown in the electrochemical capacity after eight cycles.
- Open Access
Enhancing the Mechanical Properties of Biodegradable Mg Alloys Processed by Warm HPT and Thermal Treatments
In this study, several biodegradable Mg alloys (Mg5Zn, Mg5Zn0.3Ca, Mg5Zn0.15Ca, and Mg5Zn0.15Ca0.15Zr, numbers in wt%) were investigated after thermomechanical processing via high-pressure torsion (HPT) at elevated temperature as well as after additional heat treatments. Indirect and direct analyses of microstructure revealed that the significant strength increases arise not only from dislocations and precipitates but also from vacancy agglomerates. By contrast with former low-temperature processing routes applied by the authors, a significant ductility was obtained because of temperature-induced dynamic recovery. The low initial values of Young’s modulus were not significantly affected by warm HPT-processing. nor by heat treatments afterwards. Also, corrosion resistance did not change or even increase during those treatments. Altogether, the study reveals a viable processing route for the optimization of Mg alloys to provide enhanced mechanical properties while leaving the corrosion properties unaffected, suggesting it for the use as biodegradable implant material.
Open AccessEnhancing the Mechanical Properties of Biodegradable Mg Alloys Processed by Warm HPT and Thermal Treatments
In this study, several biodegradable Mg alloys (Mg5Zn, Mg5Zn0.3Ca, Mg5Zn0.15Ca, and Mg5Zn0.15Ca0.15Zr, numbers in wt%) were investigated after thermomechanical processing via high-pressure torsion (HPT) at elevated temperature as well as after additional heat treatments. Indirect and direct analyses of microstructure revealed that the significant strength increases arise not only from dislocations and precipitates but also from vacancy agglomerates. By contrast with former low-temperature processing routes applied by the authors, a significant ductility was obtained because of temperature-induced dynamic recovery. The low initial values of Young’s modulus were not significantly affected by warm HPT-processing. nor by heat treatments afterwards. Also, corrosion resistance did not change or even increase during those treatments. Altogether, the study reveals a viable processing route for the optimization of Mg alloys to provide enhanced mechanical properties while leaving the corrosion properties unaffected, suggesting it for the use as biodegradable implant material.
- Open Access
- 3 August 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 23 (11) , 2100159
In Situ Synchrotron X‐Ray Diffraction during High‐Pressure Torsion Deformation of Ni and NiTi
A down‐sized high‐pressure torsion device is developed to be used in an INSTRON deformation machine available at the High Energy Materials Science beamline at PETRA III. This setup allows to obtain synchrotron diffraction patterns in situ during severe plastic straining. Two different materials are studied: in pure Ni, the dislocation density and coherently scattering domain size are analyzed; in NiTi shape memory alloy, amorphization and a reverse martensitic phase transformation are investigated. The in situ experiments facilitate the characterization of the microstructural evolution of these materials depending on uniaxial loading, hydrostatic pressure, and torsional strain.
- 3 August 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 23 (11) , 2100159
Open AccessIn Situ Synchrotron X‐Ray Diffraction during High‐Pressure Torsion Deformation of Ni and NiTi
A down‐sized high‐pressure torsion device is developed to be used in an INSTRON deformation machine available at the High Energy Materials Science beamline at PETRA III. This setup allows to obtain synchrotron diffraction patterns in situ during severe plastic straining. Two different materials are studied: in pure Ni, the dislocation density and coherently scattering domain size are analyzed; in NiTi shape memory alloy, amorphization and a reverse martensitic phase transformation are investigated. The in situ experiments facilitate the characterization of the microstructural evolution of these materials depending on uniaxial loading, hydrostatic pressure, and torsional strain.
- 30 March 2021
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 29 (11) , 3509-3524
High-Velocity Stretching of Renewable Polymer Blends
- 30 March 2021
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 29 (11) , 3509-3524
High-Velocity Stretching of Renewable Polymer Blends
- Open Access
The Effects of Severe Plastic Deformation and/or Thermal Treatment on the Mechanical Properties of Biodegradable Mg-Alloys
In this study, five MgZnCa alloys with low alloy content and high biocorrosion resistance were investigated during thermomechanical processing. As documented by microhardness and tensile tests, high pressure torsion (HPT)-processing and subsequent heat treatments led to strength increases of up to 250%; as much as about 1/3 of this increase was due to the heat treatment. Microstructural analyses by electron microscopy revealed a significant density of precipitates, but estimates of the Orowan strength exhibited values much smaller than the strength increases observed. Calculations using Kirchner’s model of vacancy hardening, however, showed that vacancy concentrations of 10−⁵ could have accounted for the extensive hardening observed, at least when they formed vacancy agglomerates with sizes around 50–100 nm. While such an effect has been suggested for a selected Mg-alloy already in a previous paper of the authors, in this study the effect was substantiated by combined quantitative evaluations from differential scanning calorimetry and X-ray line profile analysis. Those exhibited vacancy concentrations of up to about 10−3 with a marked percentage being part of vacancy agglomerates, which has been confirmed by evaluations of defect specific activation migration enthalpies. The variations of Young’s modulus during HPT-processing and during the subsequent thermal treatments were small. Additionally, the corrosion rate did not markedly change compared to that of the homogenized state.
Open AccessThe Effects of Severe Plastic Deformation and/or Thermal Treatment on the Mechanical Properties of Biodegradable Mg-Alloys
In this study, five MgZnCa alloys with low alloy content and high biocorrosion resistance were investigated during thermomechanical processing. As documented by microhardness and tensile tests, high pressure torsion (HPT)-processing and subsequent heat treatments led to strength increases of up to 250%; as much as about 1/3 of this increase was due to the heat treatment. Microstructural analyses by electron microscopy revealed a significant density of precipitates, but estimates of the Orowan strength exhibited values much smaller than the strength increases observed. Calculations using Kirchner’s model of vacancy hardening, however, showed that vacancy concentrations of 10−⁵ could have accounted for the extensive hardening observed, at least when they formed vacancy agglomerates with sizes around 50–100 nm. While such an effect has been suggested for a selected Mg-alloy already in a previous paper of the authors, in this study the effect was substantiated by combined quantitative evaluations from differential scanning calorimetry and X-ray line profile analysis. Those exhibited vacancy concentrations of up to about 10−3 with a marked percentage being part of vacancy agglomerates, which has been confirmed by evaluations of defect specific activation migration enthalpies. The variations of Young’s modulus during HPT-processing and during the subsequent thermal treatments were small. Additionally, the corrosion rate did not markedly change compared to that of the homogenized state.
- Open Access
Microstructural Investigation of Nanocrystalline Hydrogen-Storing Mg-Titanate Nanotube Composites Processed by High-Pressure Torsion
A high-energy ball milling and subsequent high-pressure torsion method was applied to synthesize nanocrystalline magnesium samples catalyzed by TiO2 or titanate nanotubes. The microstructure of the as-milled powders and the torqued bulk disks was characterized by X-ray diffraction. The recorded diffractograms have been evaluated by the convolutional multiple whole profile fitting algorithm, which provided microstructural parameters (average crystal size, crystallite size distribution, average dislocation density). The morphology of the nanotube-containing disks has been examined by high-resolution transmission electron microscopy. The effect of the different additives and preparation conditions on the hydrogen absorption behavior was investigated in a Sieverts’-type apparatus. It was found that the ball-milling route has a prominent effect on the dispersion and morphology of the titanate nanotubes, and the absorption capability of the Mg-based composite is highly dependent on these features.
Open AccessMicrostructural Investigation of Nanocrystalline Hydrogen-Storing Mg-Titanate Nanotube Composites Processed by High-Pressure Torsion
A high-energy ball milling and subsequent high-pressure torsion method was applied to synthesize nanocrystalline magnesium samples catalyzed by TiO2 or titanate nanotubes. The microstructure of the as-milled powders and the torqued bulk disks was characterized by X-ray diffraction. The recorded diffractograms have been evaluated by the convolutional multiple whole profile fitting algorithm, which provided microstructural parameters (average crystal size, crystallite size distribution, average dislocation density). The morphology of the nanotube-containing disks has been examined by high-resolution transmission electron microscopy. The effect of the different additives and preparation conditions on the hydrogen absorption behavior was investigated in a Sieverts’-type apparatus. It was found that the ball-milling route has a prominent effect on the dispersion and morphology of the titanate nanotubes, and the absorption capability of the Mg-based composite is highly dependent on these features.