Nilam S. Barekar
Research Subjects
Nilam S. Barekar has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Abdul Radim Asil
Brunel Centre for Advanced Solidification Technology, Brunel University of London, Uxbridge UB8 3PH, UK
1 shared publication B. K. Dhindaw
I.I.T. Kharagpur, Kharagpur, India
1 shared publication- Briji Kumar Dhindaw
Universiti Sains Malaysia
1 shared publication - C. Barbatti1 shared publication
- Carla Barbatti
Constellium Technology Centre, Uxbridge UB8 3PH, UK
1 shared publication - Dmitry G. Eskin
Brunel Centre for Advanced Solidification Technology, Brunel University of London, Uxbridge UB8 3PH, UK
1 shared publication
Latest Publications
- Open Access
- 11 November 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (11) , 500
A Novel Method to Assess Aluminium Alloy Machinability Using Shear Cracks in Chips Formed During Machining
Demand for aluminium (Al) products has increased due to their low density, high strength-to-weight ratio, thermal and electrical conductivity, and corrosion resistance. Reliable machinability assessment is important for selecting suitable alloys for manufacturing applications. However, conventional methods based on chip counting and weighing may not adequately distinguish alloys with similar chemical compositions. This study proposes an alternative method for assessing aluminium alloy machinability by quantifying the Shear Crack Initiation Layer (SCIL) in machining chips. Aluminium alloys were machined using a lathe under consistent machining parameters, and chip cross-sections were examined to quantify shear crack features and investigate differences between inner and outer chip layers. Conventional chip counting and weighing produced similar machinability values for two chemically similar alloys and showed negligible differences between the inner and outer layers of each alloy. In contrast, SCIL-based assessment revealed clear machinability differences between the inner and outer layers within each alloy and between the two chemically similar alloys. These findings demonstrate the potential of SCIL quantification to provide a more sensitive assessment of aluminium alloy machinability than conventional chip counting and weighing methods.
- 11 November 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (11) , 500
Open AccessA Novel Method to Assess Aluminium Alloy Machinability Using Shear Cracks in Chips Formed During Machining
Demand for aluminium (Al) products has increased due to their low density, high strength-to-weight ratio, thermal and electrical conductivity, and corrosion resistance. Reliable machinability assessment is important for selecting suitable alloys for manufacturing applications. However, conventional methods based on chip counting and weighing may not adequately distinguish alloys with similar chemical compositions. This study proposes an alternative method for assessing aluminium alloy machinability by quantifying the Shear Crack Initiation Layer (SCIL) in machining chips. Aluminium alloys were machined using a lathe under consistent machining parameters, and chip cross-sections were examined to quantify shear crack features and investigate differences between inner and outer chip layers. Conventional chip counting and weighing produced similar machinability values for two chemically similar alloys and showed negligible differences between the inner and outer layers of each alloy. In contrast, SCIL-based assessment revealed clear machinability differences between the inner and outer layers within each alloy and between the two chemically similar alloys. These findings demonstrate the potential of SCIL quantification to provide a more sensitive assessment of aluminium alloy machinability than conventional chip counting and weighing methods.
- Open Access
- 22 February 2025
- Published by Elsevier in Materials Letters
- Vol. 387
Effect of Ti on microstructure and mechanical properties of high strength AA6xxx alloy
- 22 February 2025
- Published by Elsevier in Materials Letters
- Vol. 387
Open AccessEffect of Ti on microstructure and mechanical properties of high strength AA6xxx alloy
- Open Access
- 25 January 2022
- Published by Springer Nature in JOM
- Vol. 74 (3) , 1218-1227
Comparative Analysis of Structure and Properties of Nb-B Inoculated Direct Chill Cast AA4032 Alloy Extruded from As-Cast and Homogenized Conditions
Al-Si wrought piston alloys can lack properties due to inefficient grain refining. A novel Al-Nb-B grain refiner was introduced some time ago, but has still not been assessed in industry for wrought alloys. This paper describes the first trial of Al-Ni-B addition and its impact on the full-scale manufacturing, structure, and properties of the AA4032 products extruded with and without billet homogenization. It is shown that Nb-B inoculation gives opportunities not only to have a refined as-cast structure but also a more homogenous distribution of the solute. In contrast, homogenization drives nucleation and coarsening of the Mg2Si phase that is retained during further extrusion and heat treatment also affecting the precipitation and properties. It was observed that non-homogenized specimens perform better during machining and tensile testing compared to homogenized specimens. The results are supported by electron microscopy investigations of microstructure formation during different steps in downstream processing.
- 25 January 2022
- Published by Springer Nature in JOM
- Vol. 74 (3) , 1218-1227
Open AccessComparative Analysis of Structure and Properties of Nb-B Inoculated Direct Chill Cast AA4032 Alloy Extruded from As-Cast and Homogenized Conditions
Al-Si wrought piston alloys can lack properties due to inefficient grain refining. A novel Al-Nb-B grain refiner was introduced some time ago, but has still not been assessed in industry for wrought alloys. This paper describes the first trial of Al-Ni-B addition and its impact on the full-scale manufacturing, structure, and properties of the AA4032 products extruded with and without billet homogenization. It is shown that Nb-B inoculation gives opportunities not only to have a refined as-cast structure but also a more homogenous distribution of the solute. In contrast, homogenization drives nucleation and coarsening of the Mg2Si phase that is retained during further extrusion and heat treatment also affecting the precipitation and properties. It was observed that non-homogenized specimens perform better during machining and tensile testing compared to homogenized specimens. The results are supported by electron microscopy investigations of microstructure formation during different steps in downstream processing.
- 23 November 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 23 (2) , 439-443
Mechanism of Microstructural Refinement of Al-Cu Alloy During Low Melt Sheared Slope Casting
- 23 November 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 23 (2) , 439-443
Mechanism of Microstructural Refinement of Al-Cu Alloy During Low Melt Sheared Slope Casting
- 14 February 2012
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 21 (11) , 2283-2289
Microstructural Evolution Under Low Shear Rates During Rheo Processing of LM25 Alloy
- 14 February 2012
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 21 (11) , 2283-2289
Microstructural Evolution Under Low Shear Rates During Rheo Processing of LM25 Alloy
- 27 April 2011
- Published by Springer Nature in Journal of Materials Research
- Vol. 26 (14) , 1702-1710
Effect of Al and Ag addition on phase formation, thermal stability, and mechanical properties of Cu–Zr-based bulk metallic glasses
- 27 April 2011
- Published by Springer Nature in Journal of Materials Research
- Vol. 26 (14) , 1702-1710
Effect of Al and Ag addition on phase formation, thermal stability, and mechanical properties of Cu–Zr-based bulk metallic glasses