Ji-Yong Eom
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ji-Yong Eom has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
Hyuk-Sang Kwon
Department of Materials Science & Engineering, KAIST, 373-1 Guseong-dong, Yuseong-gu, Daejeon 305-701, Korea
1 shared publication- HyukSang Kwon
Korea Advanced Institute of Science and Technology
1 shared publication JungWon Park
Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, 373-1 Guseong-dong, Yuseong-gu, Daejeon-si 305-701, Republic of Korea
1 shared publication
Latest Publications
- 24 March 2011
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 3 (4) , 1015-1021
Preparation of Single-Walled Carbon Nanotube/Silicon Composites and Their Lithium Storage Properties
Single-walled carbon nanotube (SWCNT)/silicon composites were produced from the purified SWCNTs and Si powder by high-energy ball-milling and then electrochemically inserted with Li using Li/(SWCNT/Si) cells. The highest reversible capacity and lowest irreversible capacity of the SWCNT/Si composites were measured to be 1845 and 474 mAh g−1 after ball-milling for 60 min, respectively. During the charge/discharge process, most of the Li ions were inserted into the SWCNT/Si composites by alloying with Si particles below 0.2 V and extracted from the SWCNT/Si composites by dealloying with Si particles around 0.5 V. The enhanced capacity and cycle performance of the SWCNT/Si composites produced by high-energy ball-milling were due primarily to the fact that SWCNTs provided a flexible conductive matrix, which compensated for the dimensional changes of Si particles during Li insertion and avoided loosening of the interparticle contacts during the crumbling of Si particles. The ball-milling contributed to a decrease in the particle size of SWCNTs and Si particles and to an increase in the electrical contact between SWCNTs and Si particles in the SWCNT/Si composites.
- 24 March 2011
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 3 (4) , 1015-1021
Preparation of Single-Walled Carbon Nanotube/Silicon Composites and Their Lithium Storage Properties
Single-walled carbon nanotube (SWCNT)/silicon composites were produced from the purified SWCNTs and Si powder by high-energy ball-milling and then electrochemically inserted with Li using Li/(SWCNT/Si) cells. The highest reversible capacity and lowest irreversible capacity of the SWCNT/Si composites were measured to be 1845 and 474 mAh g−1 after ball-milling for 60 min, respectively. During the charge/discharge process, most of the Li ions were inserted into the SWCNT/Si composites by alloying with Si particles below 0.2 V and extracted from the SWCNT/Si composites by dealloying with Si particles around 0.5 V. The enhanced capacity and cycle performance of the SWCNT/Si composites produced by high-energy ball-milling were due primarily to the fact that SWCNTs provided a flexible conductive matrix, which compensated for the dimensional changes of Si particles during Li insertion and avoided loosening of the interparticle contacts during the crumbling of Si particles. The ball-milling contributed to a decrease in the particle size of SWCNTs and Si particles and to an increase in the electrical contact between SWCNTs and Si particles in the SWCNT/Si composites.
- 1 March 2009
- Published by Elsevier in Electrochemistry Communications
- Vol. 11 (3) , 596-598
Fabrication of Sn–C composite electrodes by electrodeposition and their cycle performance for Li-ion batteries
- 1 March 2009
- Published by Elsevier in Electrochemistry Communications
- Vol. 11 (3) , 596-598
Fabrication of Sn–C composite electrodes by electrodeposition and their cycle performance for Li-ion batteries