Joanna Zurek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Joanna Zurek has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Willem Joseph Quadakkers
Institute for Energy and Climate Research, IEK-2, Forschungszentrum Jülich GmbH, Jülich, Germany
7 shared publications L. Singheiser
Forschungszentrum Jülich Institute of Energy and Climate Research (IEK‐2) 52425 Jülich (Germany)
3 shared publicationsD. Naumenko
Forschungszentrum Jülich GmbH, Jülich, Germany
2 shared publicationsE. Wessel
Institute of Energy and Climate Research (IEK-2), Forschungszentrum Jülich, 52425 Jülich, Germany
2 shared publicationsElham Hejrani
Forschungszentrum Jülich GmbH
2 shared publicationsG. H. Meier
University of Pittsburgh, Pittsburgh, 15261 PA (USA)
2 shared publications
Latest Publications
- Open Access
- 24 October 2023
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 100 (5-6) , 491-523
Effect of Surface Oxide on Decarburization Reaction in the Austenitic Steel S304HCu
In the present work, the high-temperature decarburization of the austenitic stainless steel S304HCu in Ar–4%H2–xH2O at temperatures between 1000 and 1150 °C was investigated. The focus was on determining parameters that influence the decarburization rate during heat treatment. Thermogravimetric experiments were performed with simultaneous measurements of CO release from the sample using a mass spectrometer. The variation of the experimental parameters included the composition of the atmosphere during pre-oxidation and decarburization, the temperature and the sample thickness. The results indicate that the loss of carbon from the specimen occurs faster through reaction of Cr2O3with C from the steel compared to the reaction of C at the steel surface with H2O, provided that in the former case CO can easily evaporate. The overall decarburization process is governed by competing reactions; the destruction of chromium oxide by C and the formation of oxide scale by water vapour. The relative rates of these two reactions determines whether decarburization will occur or whether formation of a protective oxide stops the release of CO, the latter being promoted at lower temperatures and high water vapour contents. A dense, sufficiently thick chromia scale retards the onset of decarburization but does eventually not stop the carbon loss. Indications were found that the destruction of a pre-formed chromia scale by carbon involves a two-step process whereby presence of hydrogen is important.
- 24 October 2023
- Published by Springer Nature in High Temperature Corrosion of Materials
- Vol. 100 (5-6) , 491-523
Open AccessEffect of Surface Oxide on Decarburization Reaction in the Austenitic Steel S304HCu
In the present work, the high-temperature decarburization of the austenitic stainless steel S304HCu in Ar–4%H2–xH2O at temperatures between 1000 and 1150 °C was investigated. The focus was on determining parameters that influence the decarburization rate during heat treatment. Thermogravimetric experiments were performed with simultaneous measurements of CO release from the sample using a mass spectrometer. The variation of the experimental parameters included the composition of the atmosphere during pre-oxidation and decarburization, the temperature and the sample thickness. The results indicate that the loss of carbon from the specimen occurs faster through reaction of Cr2O3with C from the steel compared to the reaction of C at the steel surface with H2O, provided that in the former case CO can easily evaporate. The overall decarburization process is governed by competing reactions; the destruction of chromium oxide by C and the formation of oxide scale by water vapour. The relative rates of these two reactions determines whether decarburization will occur or whether formation of a protective oxide stops the release of CO, the latter being promoted at lower temperatures and high water vapour contents. A dense, sufficiently thick chromia scale retards the onset of decarburization but does eventually not stop the carbon loss. Indications were found that the destruction of a pre-formed chromia scale by carbon involves a two-step process whereby presence of hydrogen is important.
- Open Access
- 20 July 2023
- Published by Springer Nature in Research Square
Effect of surface oxide on decarburization reaction in the austenitic steel S304HCu
In the present work, the high temperature decarburization of the austenitic stainless steel S304HCu in Ar-(4%H2)-x H2O at temperatures between 1000 and 1150°C was investigated. The focus was on determining parameters that influence the decarburization rate during heat treatment. Thermogravimetric experiments were performed with simultaneous measurements of CO release from the sample using a mass spectrometer. The variation of the experimental parameters included the composition of the atmosphere during pre-oxidation and decarburization, the temperature and the sample thickness. The results indicate that the loss of carbon from the specimen occurs faster through reaction of Cr2O3 with C from the steel compared to the reaction of C at the steel surface with H2O, provided that in the former case CO can easily evaporate. The overall decarburization process is governed by competing reactions; the destruction of chromium oxide by C and the formation of oxide scale by water vapour. The relative rates of these two reactions determines whether decarburization will occur or whether formation of a protective oxide stops the release of CO, the latter being promoted at lower temperatures and high water vapour contents. A dense, sufficiently thick chromia scale retards the onset of decarburization but does eventually not stop the carbon loss. Indications were found that the destruction of a pre-formed chromia scale by carbon involves a two-step process whereby presence of hydrogen is important.
- 20 July 2023
- Published by Springer Nature in Research Square
Open AccessEffect of surface oxide on decarburization reaction in the austenitic steel S304HCu
In the present work, the high temperature decarburization of the austenitic stainless steel S304HCu in Ar-(4%H2)-x H2O at temperatures between 1000 and 1150°C was investigated. The focus was on determining parameters that influence the decarburization rate during heat treatment. Thermogravimetric experiments were performed with simultaneous measurements of CO release from the sample using a mass spectrometer. The variation of the experimental parameters included the composition of the atmosphere during pre-oxidation and decarburization, the temperature and the sample thickness. The results indicate that the loss of carbon from the specimen occurs faster through reaction of Cr2O3 with C from the steel compared to the reaction of C at the steel surface with H2O, provided that in the former case CO can easily evaporate. The overall decarburization process is governed by competing reactions; the destruction of chromium oxide by C and the formation of oxide scale by water vapour. The relative rates of these two reactions determines whether decarburization will occur or whether formation of a protective oxide stops the release of CO, the latter being promoted at lower temperatures and high water vapour contents. A dense, sufficiently thick chromia scale retards the onset of decarburization but does eventually not stop the carbon loss. Indications were found that the destruction of a pre-formed chromia scale by carbon involves a two-step process whereby presence of hydrogen is important.
- 25 July 2019
- Published by Springer Nature in Oxidation of Metals
- Vol. 92 (3-4) , 353-377
Behaviour of Metallic Materials in Simulated Service Environments of CO2/H2O Co-electrolysis Systems for Power-to-X Application
- 25 July 2019
- Published by Springer Nature in Oxidation of Metals
- Vol. 92 (3-4) , 353-377
Behaviour of Metallic Materials in Simulated Service Environments of CO2/H2O Co-electrolysis Systems for Power-to-X Application
- 1 September 2017
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 717, 240-253
Temperature dependence of phase composition in W and Si-alloyed high chromium ferritic steels for SOFC interconnect applications
- 1 September 2017
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 717, 240-253
Temperature dependence of phase composition in W and Si-alloyed high chromium ferritic steels for SOFC interconnect applications
- 16 August 2015
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 71 (11) , 1342-1359
Effect of Surface Condition on Steam Oxidation of Martensitic Steels and Nickel-Based Alloys
The steam oxidation behavior of inner tube surfaces in the as-manufactured condition for selected martensitic steels and nickel-based alloys was compared with that of standard laboratory test coupons that were ground to a 600 grit surface finish prior to the steam exposure. Exposures up to 10,000 h in the temperature range of 550°C to 700°C revealed that the as-delivered inner tube surfaces may exhibit substantial internal oxidation as a result of the (solution) heat treatment in the final stages of the manufacturing process. The internal oxides contained mainly chromia in the martensitic steels and alumina and/or titania in the nickel-based alloys. For the latter materials, the internal oxidation, especially of Ti, caused the steam-grown external chromia scales to be generally thinner than those observed on the specimens that were ground prior to oxidation testing. For the martensitic steels, the internal oxidation modified the incorporation of Cr (Mn, Si) into the surface scales, thus suppressing the formation of protective chromia-based surface scales. For all studied materials, the internal oxidation present in the as-received condition may affect the steam oxidation behavior at temperatures in the range of 550°C to 700°C up to 10,000 h exposure time.
- 16 August 2015
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 71 (11) , 1342-1359
Effect of Surface Condition on Steam Oxidation of Martensitic Steels and Nickel-Based Alloys
The steam oxidation behavior of inner tube surfaces in the as-manufactured condition for selected martensitic steels and nickel-based alloys was compared with that of standard laboratory test coupons that were ground to a 600 grit surface finish prior to the steam exposure. Exposures up to 10,000 h in the temperature range of 550°C to 700°C revealed that the as-delivered inner tube surfaces may exhibit substantial internal oxidation as a result of the (solution) heat treatment in the final stages of the manufacturing process. The internal oxides contained mainly chromia in the martensitic steels and alumina and/or titania in the nickel-based alloys. For the latter materials, the internal oxidation, especially of Ti, caused the steam-grown external chromia scales to be generally thinner than those observed on the specimens that were ground prior to oxidation testing. For the martensitic steels, the internal oxidation modified the incorporation of Cr (Mn, Si) into the surface scales, thus suppressing the formation of protective chromia-based surface scales. For all studied materials, the internal oxidation present in the as-received condition may affect the steam oxidation behavior at temperatures in the range of 550°C to 700°C up to 10,000 h exposure time.
- 28 October 2014
- Published by Wiley in Materials and Corrosion
- Vol. 66 (4) , 315-327
Microstructural stability and oxidation behavior of Sanicro 25 during long‐term steam exposure in the temperature range 600–750 °C
The aim of the present study is the investigation of the microstructural features and the oxidation resistance of the austenitic steel Sanicro 25 during long‐term steam exposure up to 10 000 h in the temperature range 600–750 °C. Steel microstructures of specimens after exposure times of 1000, 3000, and 10 000 h were analyzed by scanning and transmission electron microscopy as well as X‐ray diffraction. The steam oxidation behavior was estimated by gravimetry in combination with microstructural investigations using the above mentioned analysis tools as well as depth profiling by secondary neutrals mass spectrometry. In the as‐received condition, the only detectable precipitate was Z‐(Nb,Cr)N phase. After exposures in the temperature range 600–750 °C various amounts of the following additional phases were identified: chromium nitride, µ‐phase, and carbides with various compositions. Chromia base surface scales formed during exposure at 600–700 °C, whereas more rapidly growing Fe/Cr‐rich oxides were found at 750 °C. The oxidation rates were only slightly higher than those of a typical nickel base alloy such as alloy 617. In the subsurface zones, depletion of scale forming elements was accompanied by enrichment of tungsten and copper‐rich phases.
- 28 October 2014
- Published by Wiley in Materials and Corrosion
- Vol. 66 (4) , 315-327
Microstructural stability and oxidation behavior of Sanicro 25 during long‐term steam exposure in the temperature range 600–750 °C
The aim of the present study is the investigation of the microstructural features and the oxidation resistance of the austenitic steel Sanicro 25 during long‐term steam exposure up to 10 000 h in the temperature range 600–750 °C. Steel microstructures of specimens after exposure times of 1000, 3000, and 10 000 h were analyzed by scanning and transmission electron microscopy as well as X‐ray diffraction. The steam oxidation behavior was estimated by gravimetry in combination with microstructural investigations using the above mentioned analysis tools as well as depth profiling by secondary neutrals mass spectrometry. In the as‐received condition, the only detectable precipitate was Z‐(Nb,Cr)N phase. After exposures in the temperature range 600–750 °C various amounts of the following additional phases were identified: chromium nitride, µ‐phase, and carbides with various compositions. Chromia base surface scales formed during exposure at 600–700 °C, whereas more rapidly growing Fe/Cr‐rich oxides were found at 750 °C. The oxidation rates were only slightly higher than those of a typical nickel base alloy such as alloy 617. In the subsurface zones, depletion of scale forming elements was accompanied by enrichment of tungsten and copper‐rich phases.
- 21 August 2014
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 86 (10) , 1726-1734
Corrosion Behavior of Metallic Materials for Innovative Gasification Processes
Metallische Werkstoffe für hochbeanspruchte Sauerstoffdüsen und Abhitzekessel wurden auf ihre Korrosionsbeständigkeit in einem H2/H2O/H2S‐Laborgas untersucht. In Screening‐Versuchen an ferritischen und austenitischen Stählen und Nickelbasislegierungen wurden vielversprechende Legierungen ermittelt. Für alle untersuchten Werkstoffe, mit einer Ausnahme, ergab sich eine Bell‐Shape‐Abhängigkeit der Oxidationskinetik. Durch Untersuchungen an Modelllegierungen wird die Wirkung einzelner Legierungselemente auf die Korrosionsmechanismen ermittelt, um hieraus optimierte Legierungszusammensetzungen herzuleiten.
- 21 August 2014
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 86 (10) , 1726-1734
Corrosion Behavior of Metallic Materials for Innovative Gasification Processes
Metallische Werkstoffe für hochbeanspruchte Sauerstoffdüsen und Abhitzekessel wurden auf ihre Korrosionsbeständigkeit in einem H2/H2O/H2S‐Laborgas untersucht. In Screening‐Versuchen an ferritischen und austenitischen Stählen und Nickelbasislegierungen wurden vielversprechende Legierungen ermittelt. Für alle untersuchten Werkstoffe, mit einer Ausnahme, ergab sich eine Bell‐Shape‐Abhängigkeit der Oxidationskinetik. Durch Untersuchungen an Modelllegierungen wird die Wirkung einzelner Legierungselemente auf die Korrosionsmechanismen ermittelt, um hieraus optimierte Legierungszusammensetzungen herzuleiten.
- 12 January 2011
- Published by Wiley in Materials and Corrosion
- Vol. 62 (6) , 504-513
Temperature and gas composition dependence of internal oxidation kinetics of an Fe-10%Cr alloy in water vapour containing environments
Recently it was proposed, that the hampered formation of external protective chromia scales on FeCr‐alloys in water vapour containing, low‐pO2 gases is correlated with enhanced internal oxidation of chromium. In the present study the internal oxidation kinetics of Fe10Cr (in mass%) during isothermal oxidation in ArH2H2O mixtures at temperatures in the range 800–1050 °C has been investigated. It was found that the tendency for Cr to become internally oxidized decreased with decreasing temperature. At the higher test temperatures the internal oxide precipitates consisted of Fe/Cr‐spinel. With decreasing temperature the precipitates near the oxidation front gradually exhibited increasing amounts of chromia. At 900 °C the oxidation morphology in the ArH2 base gas mixture changed from exclusive internal oxidation of Cr at a water vapour content of 2% towards a combined internal Cr oxidation and external Fe‐oxide formation at higher water vapour partial pressures.
- 12 January 2011
- Published by Wiley in Materials and Corrosion
- Vol. 62 (6) , 504-513
Temperature and gas composition dependence of internal oxidation kinetics of an Fe-10%Cr alloy in water vapour containing environments
Recently it was proposed, that the hampered formation of external protective chromia scales on FeCr‐alloys in water vapour containing, low‐pO2 gases is correlated with enhanced internal oxidation of chromium. In the present study the internal oxidation kinetics of Fe10Cr (in mass%) during isothermal oxidation in ArH2H2O mixtures at temperatures in the range 800–1050 °C has been investigated. It was found that the tendency for Cr to become internally oxidized decreased with decreasing temperature. At the higher test temperatures the internal oxide precipitates consisted of Fe/Cr‐spinel. With decreasing temperature the precipitates near the oxidation front gradually exhibited increasing amounts of chromia. At 900 °C the oxidation morphology in the ArH2 base gas mixture changed from exclusive internal oxidation of Cr at a water vapour content of 2% towards a combined internal Cr oxidation and external Fe‐oxide formation at higher water vapour partial pressures.
- 1 August 2008
- Published by Springer Nature in Journal of Materials Science
- Vol. 43 (16) , 5591-5598
Effect of oxygen partial pressure on the oxidation behaviour of an yttria dispersion strengthened NiCr-base alloy
- 1 August 2008
- Published by Springer Nature in Journal of Materials Science
- Vol. 43 (16) , 5591-5598
Effect of oxygen partial pressure on the oxidation behaviour of an yttria dispersion strengthened NiCr-base alloy