Frank Taylor
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Frank Taylor has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
James C. Craig
U.S. Department of Agriculture, Agriculture Research Service
2 shared publicationsM. J. Kurantz
U.S. Department of Agriculture, Agriculture Research Service
2 shared publicationsAndrew J. McAloon
U.S. Department of Agriculture, Eastern Regional Research Center, Agricultural Research Service, Wyndmoor, Pennsylvania 19038
1 shared publicationAndrew J. Mcaloon
Agricultural Research Service
1 shared publicationJ. C. Craig Jr.
U.S. Department of Agriculture, Agricultural Research Service, Eastern Regional Research Center, 600 E. Mermaid Lane, Wyndmoor, PA 19038, USA Tel.: (215) 233 6501 Fax: (215) 233 6795 US
1 shared publicationJames C Craig
Agricultural Research Service Eastern Regional Research Center, U.S. Department of Agriculture 600 East Mermaid Lane 19038 Wyndmoor PA
1 shared publication
Latest Publications
- 1 January 2003
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 104 (2) , 141-148
Corn-Milling Pretreatment with Anhydrous Ammonia
Exposure to anhydrous ammonia has been suggested as a pretreatment for corn milling. Batches of corn were exposed to ammonia under controlled conditions. The amounts of ammonia absorbed and reacted with the corn were measured. The amounts were not more than are needed as nutritional supplement for yeast fermentation to ethanol. Loosening of the hull was observed qualitatively, and subsequent shearing in a disk mill followed by steeping for 2, 4, 6, or 8h showed that germ could be recovered at higher yield and after a shorter steeping time compared to untreated control batches. Quality of oil was not affected by treatment with ammonia.
- 1 January 2003
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 104 (2) , 141-148
Corn-Milling Pretreatment with Anhydrous Ammonia
Exposure to anhydrous ammonia has been suggested as a pretreatment for corn milling. Batches of corn were exposed to ammonia under controlled conditions. The amounts of ammonia absorbed and reacted with the corn were measured. The amounts were not more than are needed as nutritional supplement for yeast fermentation to ethanol. Loosening of the hull was observed qualitatively, and subsequent shearing in a disk mill followed by steeping for 2, 4, 6, or 8h showed that germ could be recovered at higher yield and after a shorter steeping time compared to untreated control batches. Quality of oil was not affected by treatment with ammonia.
- 1 January 2001
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 94 (1) , 41-50
Fermentation and Costs of Fuel Ethanol from Corn with Quick-Germ Process
The Quick-Germ process developed at the University of Illinois at Urbana-Champaign is a way to obtain corn oil, but with lower capital costs than the traditional wet-milling process. Quick-Germ has the potential to increase the coproduct credits and profitability of the existing dry-grind fuel ethanol process, but the fermentability of the corn remaining after oil recovery has not been tested. Therefore, a series of pilot scale (50 L) fermentations was carefully controlled and monitored with unique methods for standard inoculation and automatic sampling. It was found that the concentration of suspended solids was significantly reduced in the Quick-Germ fermentations. When compared at the same concentration of fermentable sugars, the fermentation rate and yield were not statistically different from controls. When Quick-Germ was integrated into a state-of-the-art dry-grind fuel ethanol process, computer simulation and cost models indicated savings of approx $0.01/L of ethanol ($0.04/gal) with the Quick-Germ process. Additional savings associated with the lower suspended solids could not be quantified and were not included. However, the savings are sensitive to the price of corn oil.
- 1 January 2001
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 94 (1) , 41-50
Fermentation and Costs of Fuel Ethanol from Corn with Quick-Germ Process
The Quick-Germ process developed at the University of Illinois at Urbana-Champaign is a way to obtain corn oil, but with lower capital costs than the traditional wet-milling process. Quick-Germ has the potential to increase the coproduct credits and profitability of the existing dry-grind fuel ethanol process, but the fermentability of the corn remaining after oil recovery has not been tested. Therefore, a series of pilot scale (50 L) fermentations was carefully controlled and monitored with unique methods for standard inoculation and automatic sampling. It was found that the concentration of suspended solids was significantly reduced in the Quick-Germ fermentations. When compared at the same concentration of fermentable sugars, the fermentation rate and yield were not statistically different from controls. When Quick-Germ was integrated into a state-of-the-art dry-grind fuel ethanol process, computer simulation and cost models indicated savings of approx $0.01/L of ethanol ($0.04/gal) with the Quick-Germ process. Additional savings associated with the lower suspended solids could not be quantified and were not included. However, the savings are sensitive to the price of corn oil.
- 1 January 2000
- Published by Wiley in Biotechnology Progress
- Vol. 16 (4) , 541-547
Dry‐Grind Process for Fuel Ethanol by Continuous Fermentation and Stripping
Conversion of a high‐solids saccharified corn mash to ethanol by continuous fermentation and stripping was successfully demonstrated in a pilot plant consuming 25 kg of corn per day. A mathematical model based on previous pilot plant results accurately predicts the specific growth rate obtained from these latest results. This model was incorporated into a simulation of a complete dry‐grind corn‐to‐ethanol plant, and the cost of ethanol production was compared with that of a conventional process. The results indicate a savings of $0.03 per gallon of ethanol produced by the stripping process. The savings with stripping result from the capacity to ferment a more concentrated corn mash so there is less water to remove downstream.
- 1 January 2000
- Published by Wiley in Biotechnology Progress
- Vol. 16 (4) , 541-547
Dry‐Grind Process for Fuel Ethanol by Continuous Fermentation and Stripping
Conversion of a high‐solids saccharified corn mash to ethanol by continuous fermentation and stripping was successfully demonstrated in a pilot plant consuming 25 kg of corn per day. A mathematical model based on previous pilot plant results accurately predicts the specific growth rate obtained from these latest results. This model was incorporated into a simulation of a complete dry‐grind corn‐to‐ethanol plant, and the cost of ethanol production was compared with that of a conventional process. The results indicate a savings of $0.03 per gallon of ethanol produced by the stripping process. The savings with stripping result from the capacity to ferment a more concentrated corn mash so there is less water to remove downstream.
- 26 September 1997
- Published by Springer Nature in Applied Microbiology and Biotechnology
- Vol. 48 (3) , 311-316
Effects of ethanol concentration and stripping temperature on continuous fermentation rate
The operation of a pilot plant consisting of a 14-l fermentor, 10-cm packed column and condenser for continuous fermentation and stripping of ethanol was stable for more than 100 days. The feed consisted of a non-sterile solution of 560 g/l glucose with 100 g/l corn steep water. Fouling of the packing in the column with attached growth of yeast cells was controlled by in situ washing at intervals of 3–6 days. A computer simulation of the pilot plant was developed and used to analyze the data. The productivity of the continuous fermentor varied from 14 g ethanol to 17 g ethanol l−1 h−1. The yield was equal to the maximum theoretically possible: 0.51 g ethanol/g glucose consumed. Results are fit to linear models for the effects of ethanol concentration on specific growth rate and cell yield, and for the effect of stripping temperature on specific growth rate.
- 26 September 1997
- Published by Springer Nature in Applied Microbiology and Biotechnology
- Vol. 48 (3) , 311-316
Effects of ethanol concentration and stripping temperature on continuous fermentation rate
The operation of a pilot plant consisting of a 14-l fermentor, 10-cm packed column and condenser for continuous fermentation and stripping of ethanol was stable for more than 100 days. The feed consisted of a non-sterile solution of 560 g/l glucose with 100 g/l corn steep water. Fouling of the packing in the column with attached growth of yeast cells was controlled by in situ washing at intervals of 3–6 days. A computer simulation of the pilot plant was developed and used to analyze the data. The productivity of the continuous fermentor varied from 14 g ethanol to 17 g ethanol l−1 h−1. The yield was equal to the maximum theoretically possible: 0.51 g ethanol/g glucose consumed. Results are fit to linear models for the effects of ethanol concentration on specific growth rate and cell yield, and for the effect of stripping temperature on specific growth rate.