Brian. E. Reed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Brian. E. Reed has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Anjuman A. Islam
Research Assistant Professor, Dept. of Chemical Biochemical and Environmental Engineering, Univ. of Maryland Baltimore County, TRC 284, 5200 Westland Blvd., Baltimore, MD 21250
2 shared publications - Christopher J. Hennigan
Department of Chemical, Biochemical and Environmental Engineering, University of Maryland, Baltimore County, Baltimore, 21250, USA
2 shared publications Jayashree Yalamanchili
Department of Chemical, Biochemical and Environmental Engineering, University of Maryland, Baltimore County, 1000 Hilltop Circle, Baltimore, Maryland 21250, USA
2 shared publications- Roger C. Viadero
Department of Civil and Environmental Engineering, West Virginia University, Morgantown, WV 26506
2 shared publications - Ronald L. Vaughan
Ph.D. Graduate, Dept. of Civil and Environmental Engineering, E2509 Engineering Building East, Univ. of Missouri-Columbia, Columbia, MO 65211-2200
2 shared publications Wei Lin
2 shared publications
Latest Publications
- 1 April 2022
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Processes & Impacts
- Vol. 24 (5) , 762-772
Precipitation of aqueous transition metals in particulate matter during the dithiothreitol (DTT) oxidative potential assay
Many aqueous transition metals in PM precipitate in the DTT assay.
- 1 April 2022
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Processes & Impacts
- Vol. 24 (5) , 762-772
Precipitation of aqueous transition metals in particulate matter during the dithiothreitol (DTT) oxidative potential assay
Many aqueous transition metals in PM precipitate in the DTT assay.
- 21 December 2020
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Processes & Impacts
- Vol. 23 (1) , 160-169
Fate of transition metals in PO 4 -based in vitro assays: equilibrium modeling and macroscopic studies
Transition metals are thought to be among the most toxic components in atmospheric particulate matter (PM) due to their role in catalyzing reactive oxygen species (ROS) formation. We show that precipitation of the transition metals Fe(II), Fe(III), and Mn(II) are thermodynamically favored in phosphate-based assays used to measure the oxidative potential (OP) – a surrogate for toxicity – of PM. Fe and Mn precipitation is likely to occur at extremely low metal concentrations (100 μM) with visible precipitates provide quasi-validation of the thermodynamic modeling. Oxidation of Fe(II) to Fe(III) is likely to be rapid in all in vitro OP assays, transforming Fe to a much less soluble form. Fe precipitates are likely to increase the rate of precipitation of other metals and possibly induce co-precipitation. These results have direct relevance for all PO4-based assays; the implications for studies of PM toxicity are discussed.
- 21 December 2020
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Processes & Impacts
- Vol. 23 (1) , 160-169
Fate of transition metals in PO 4 -based in vitro assays: equilibrium modeling and macroscopic studies
Transition metals are thought to be among the most toxic components in atmospheric particulate matter (PM) due to their role in catalyzing reactive oxygen species (ROS) formation. We show that precipitation of the transition metals Fe(II), Fe(III), and Mn(II) are thermodynamically favored in phosphate-based assays used to measure the oxidative potential (OP) – a surrogate for toxicity – of PM. Fe and Mn precipitation is likely to occur at extremely low metal concentrations (100 μM) with visible precipitates provide quasi-validation of the thermodynamic modeling. Oxidation of Fe(II) to Fe(III) is likely to be rapid in all in vitro OP assays, transforming Fe to a much less soluble form. Fe precipitates are likely to increase the rate of precipitation of other metals and possibly induce co-precipitation. These results have direct relevance for all PO4-based assays; the implications for studies of PM toxicity are discussed.
- 6 February 2020
- Published by Taylor & Francis
- p. 429-440
Oil-Based Lubricant/Coolant Treatment by High-Shear Rotary Ultrafiltration
The SpinTek high-shear rotary ultrafiltration system was effective in concentrating oily feeds from about 5% oil to as high as 75% while maintaining a high permeate flux. The decoupling of the turbulence promotion (used to reduce concentration polarization) from feed pressurization by rotating the membrane was the primary reason for the increase in system performance over that commonly observed with conventional cross-flow membrane systems.
- 6 February 2020
- Published by Taylor & Francis
- p. 429-440
Oil-Based Lubricant/Coolant Treatment by High-Shear Rotary Ultrafiltration
The SpinTek high-shear rotary ultrafiltration system was effective in concentrating oily feeds from about 5% oil to as high as 75% while maintaining a high permeate flux. The decoupling of the turbulence promotion (used to reduce concentration polarization) from feed pressurization by rotating the membrane was the primary reason for the increase in system performance over that commonly observed with conventional cross-flow membrane systems.
- 1 January 2014
- Published by American Society of Civil Engineers (ASCE) in Journal of Hazardous, Toxic, and Radioactive Waste
- Vol. 18 (1) , 2-10
Removal of Toxicity, COD, and Fe from a Metal-Working Facility UF Permeate
- 1 January 2014
- Published by American Society of Civil Engineers (ASCE) in Journal of Hazardous, Toxic, and Radioactive Waste
- Vol. 18 (1) , 2-10
Removal of Toxicity, COD, and Fe from a Metal-Working Facility UF Permeate
- 1 May 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 139 (5) , 661-666
Ferrate and Alkaline Chlorination Treatment of Cyanide-Heavy Metal Maritime Wastewater
Ferrate [Fe(VI)] and alkaline chlorination (AC) were investigated for the treatment of a maritime wastewater (CN, Cd, Cu, Ni, Pb, and Zn) in a seawater matrix. AC reduced CN concentrations but large dosages were required (0.018–0.056 mol CN consumed/mol HOCl). Metal removal occurred during the first stage () but the amount of sludge produced was large due to formation. Fe(VI) was effective in oxidizing CN and removing heavy metals to low levels without pH adjustment. Fe(VI) requirements [] were higher than those observed for other wastes but are considered more manageable compared with HOCl. Metal removal occurred by adsorption and coprecipitation with Fe(III) oxide, which results from the oxidation of Fe(VI). During staged treatment, metal removal and CN destruction increased [2× for Cd, 3× for Cu, 2.7× for Ni, 0.12 to 0.18 mol CN consumed/mol Fe(VI)]. Fe(III) oxide was relatively easy to separate using ultrafiltration tubular membranes and the amount of sludge produced is much less than what would occur with AC. The Fe(III) oxide was separated using ultrafiltration with the amount of sludge produced much less than AC.- 1 May 2013
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 139 (5) , 661-666
Ferrate and Alkaline Chlorination Treatment of Cyanide-Heavy Metal Maritime Wastewater
Ferrate [Fe(VI)] and alkaline chlorination (AC) were investigated for the treatment of a maritime wastewater (CN, Cd, Cu, Ni, Pb, and Zn) in a seawater matrix. AC reduced CN concentrations but large dosages were required (0.018–0.056 mol CN consumed/mol HOCl). Metal removal occurred during the first stage () but the amount of sludge produced was large due to formation. Fe(VI) was effective in oxidizing CN and removing heavy metals to low levels without pH adjustment. Fe(VI) requirements [] were higher than those observed for other wastes but are considered more manageable compared with HOCl. Metal removal occurred by adsorption and coprecipitation with Fe(III) oxide, which results from the oxidation of Fe(VI). During staged treatment, metal removal and CN destruction increased [2× for Cd, 3× for Cu, 2.7× for Ni, 0.12 to 0.18 mol CN consumed/mol Fe(VI)]. Fe(III) oxide was relatively easy to separate using ultrafiltration tubular membranes and the amount of sludge produced is much less than what would occur with AC. The Fe(III) oxide was separated using ultrafiltration with the amount of sludge produced much less than AC.- 15 September 2010
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 45 (14) , 2051-2063
Removal of As(V) Using an Iron-Impregnated Ion Exchange Bead
The ability of an iron-impregnated ion exchange bead (PWX5) to remove As(V) from ground water was investigated. The effects of particle size, solution pH, As(V) concentration, competition, adsorbent concentration, temperature, iron content, and iron accessibility on removal kinetics and/or equilibrium were determined. PWX5's performance was compared to other iron-based adsorbents, primarily Bayoxide® E-33 (E-33), a granular ferric oxide, for arsenic removal performance. All of the factors cited impacted either the amount of As(V) adsorbed or the rate of adsorption. Stirred batch reactor data showed the rate of adsorption increased as particle size decreased and bottle point isotherm data showed As(V) adsorption maximum capacity increased with higher initial adsorbate concentration. The presence of phosphate and silicate reduced the amount of As(V) adsorbed as did a pH > 7.0. PWX5 is durable, rather homogeneous in size and effective at removing As(V). It is a viable alternative to E-33 which has a wider size distribution and wears more easily.
- 15 September 2010
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 45 (14) , 2051-2063
Removal of As(V) Using an Iron-Impregnated Ion Exchange Bead
The ability of an iron-impregnated ion exchange bead (PWX5) to remove As(V) from ground water was investigated. The effects of particle size, solution pH, As(V) concentration, competition, adsorbent concentration, temperature, iron content, and iron accessibility on removal kinetics and/or equilibrium were determined. PWX5's performance was compared to other iron-based adsorbents, primarily Bayoxide® E-33 (E-33), a granular ferric oxide, for arsenic removal performance. All of the factors cited impacted either the amount of As(V) adsorbed or the rate of adsorption. Stirred batch reactor data showed the rate of adsorption increased as particle size decreased and bottle point isotherm data showed As(V) adsorption maximum capacity increased with higher initial adsorbate concentration. The presence of phosphate and silicate reduced the amount of As(V) adsorbed as did a pH > 7.0. PWX5 is durable, rather homogeneous in size and effective at removing As(V). It is a viable alternative to E-33 which has a wider size distribution and wears more easily.
- 1 January 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 133 (1) , 121-124
Modeling As(V) Removal in Iron Oxide Impregnated Activated Carbon Columns
Iron oxide impregnated onto an activated carbon has a high arsenic (As) removal capacity with the potential to be used in existing activated carbon column systems. Objectives of this research were to investigate removal from aqueous-phase systems using fixed-beds packed with and to determine if the triple layer model (TLM) with the homogeneous surface diffusion model (HSDM) could describe removal in the columns. Rapid small-scale column tests (RSSCT) were conducted at various empty bed contact times (EBCT). Effluent breakthrough was incipient for the 0.20-min EBCT experiment, whereas bed volumes of water at 1-mg/L inlet concentration of was treated at an EBCT of before breakthrough occurred. The TLM with three surface reactions coupled with the HSDM provided accurate prediction of removal in the RSSCT.- 1 January 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 133 (1) , 121-124
Modeling As(V) Removal in Iron Oxide Impregnated Activated Carbon Columns
Iron oxide impregnated onto an activated carbon has a high arsenic (As) removal capacity with the potential to be used in existing activated carbon column systems. Objectives of this research were to investigate removal from aqueous-phase systems using fixed-beds packed with and to determine if the triple layer model (TLM) with the homogeneous surface diffusion model (HSDM) could describe removal in the columns. Rapid small-scale column tests (RSSCT) were conducted at various empty bed contact times (EBCT). Effluent breakthrough was incipient for the 0.20-min EBCT experiment, whereas bed volumes of water at 1-mg/L inlet concentration of was treated at an EBCT of before breakthrough occurred. The TLM with three surface reactions coupled with the HSDM provided accurate prediction of removal in the RSSCT.- 1 September 2000
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 126 (9) , 807-814
Recovery of Metal Working Fluids Using Chelation-Ultrafiltration Process
Metal working (MW) fluids are used to control friction and temperature, improve workpiece surface quality, and reduce tool wear. The batch-life of the MW fluid investigated was controlled primarily by the concentration of metallic soaps (complexes between the oil emulsifier and Al/Mg. Ethylenediaminetetraacetic acid, a strong metal chelator, was added to the MW fluid to break the oil-Al/Mg complexes. The aqueous-phase ethylenediaminetetraacetic acid-Al/Mg complexes were then separated from the oil phase by ultrafiltration (UF). Al levels were reduced between 39 and 49%, and Mg levels were reduced between 67 and 77%. Al transfer from the oil phase to the aqueous phase was slow and increased during UF concentration. Rinsing the concentrated MW fluid with deionized water decreased the ash content but had a lesser impact on Al/Mg removal. Al mass balances produced errors of 2.8% for run 3 and 6.2% for run 4. The UF system (0.11-μm ceramic membrane) effectively separated the oil and aqueous phases. Permeate turbidity was generally 2-h (230 to 130 gal./ft2-day) depending on the degree of concentration.
- 1 September 2000
- Published by American Society of Civil Engineers (ASCE) in Journal of Environmental Engineering
- Vol. 126 (9) , 807-814
Recovery of Metal Working Fluids Using Chelation-Ultrafiltration Process
Metal working (MW) fluids are used to control friction and temperature, improve workpiece surface quality, and reduce tool wear. The batch-life of the MW fluid investigated was controlled primarily by the concentration of metallic soaps (complexes between the oil emulsifier and Al/Mg. Ethylenediaminetetraacetic acid, a strong metal chelator, was added to the MW fluid to break the oil-Al/Mg complexes. The aqueous-phase ethylenediaminetetraacetic acid-Al/Mg complexes were then separated from the oil phase by ultrafiltration (UF). Al levels were reduced between 39 and 49%, and Mg levels were reduced between 67 and 77%. Al transfer from the oil phase to the aqueous phase was slow and increased during UF concentration. Rinsing the concentrated MW fluid with deionized water decreased the ash content but had a lesser impact on Al/Mg removal. Al mass balances produced errors of 2.8% for run 3 and 6.2% for run 4. The UF system (0.11-μm ceramic membrane) effectively separated the oil and aqueous phases. Permeate turbidity was generally 2-h (230 to 130 gal./ft2-day) depending on the degree of concentration.
- 1 January 2000
- Published by Water Environment Federation in Proceedings of the Water Environment Federation
- Vol. 2000 (5) , 545-573
DEVELOPMENT AND OPERATION OF A FULL-SCALE OILY WASTEWATER TREATMENT SYSTEM
- 1 January 2000
- Published by Water Environment Federation in Proceedings of the Water Environment Federation
- Vol. 2000 (5) , 545-573
DEVELOPMENT AND OPERATION OF A FULL-SCALE OILY WASTEWATER TREATMENT SYSTEM
- 1 September 1997
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 32 (14) , 2367-2384
NaOH Regeneration of Pb and Phenol-Laden Activated Carbon. I. Batch Study Results
Granular activated carbon (GAC) has been used to remove organics and metals simultaneously from wastewaters (4). For a regeneration procedure to be effective on GAC containing both metals and organics, it must remove both the metals and organic compounds. In this study, GAC saturated with Pb and phenol was regenerated using an NaOH rinse in batch mode. Four variables were investigated: 1) regenerant concentration (0, 0.1, and 1.0 N), 2) regenerant to carbon mass ratio (5:1 and 10:1), 3) regenerant temperature (22 and 80°C), and 4) regeneration time (0.33, 1, 3, 7, and 21 days). Maximum regenerations of 47% for Pb and 48% for phenol were observed. The 1.0 N NaOH regenerated a higher percentage of both Pb and phenol when compared to the other regenerants. The 10:1 regenerant to carbon ratio resulted in increased regeneration over the 5:1 regenerations. Pb regeneration was slightly higher at 80°C than at 22°C whereas phenol regeneration was slightly lower at 80°C than at 22°C. Maximum regenerations for both Pb and phenol were observed within the first day of regeneration, in most cases within the first 8 hours.
- 1 September 1997
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 32 (14) , 2367-2384
NaOH Regeneration of Pb and Phenol-Laden Activated Carbon. I. Batch Study Results
Granular activated carbon (GAC) has been used to remove organics and metals simultaneously from wastewaters (4). For a regeneration procedure to be effective on GAC containing both metals and organics, it must remove both the metals and organic compounds. In this study, GAC saturated with Pb and phenol was regenerated using an NaOH rinse in batch mode. Four variables were investigated: 1) regenerant concentration (0, 0.1, and 1.0 N), 2) regenerant to carbon mass ratio (5:1 and 10:1), 3) regenerant temperature (22 and 80°C), and 4) regeneration time (0.33, 1, 3, 7, and 21 days). Maximum regenerations of 47% for Pb and 48% for phenol were observed. The 1.0 N NaOH regenerated a higher percentage of both Pb and phenol when compared to the other regenerants. The 10:1 regenerant to carbon ratio resulted in increased regeneration over the 5:1 regenerations. Pb regeneration was slightly higher at 80°C than at 22°C whereas phenol regeneration was slightly lower at 80°C than at 22°C. Maximum regenerations for both Pb and phenol were observed within the first day of regeneration, in most cases within the first 8 hours.