Udo Wagenknecht
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Udo Wagenknecht has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Gert Heinrich
Department of Processing, Leibniz-Institut für Polymerforschung Dresden e. V., Dresden, Germany
6 shared publications- Ahmad Mousa
Al-Balqa Applied University
4 shared publications - Uwe Gohs
Leibniz-Institut für Polymerforschung Dresden e.V., Hohe Str. 6, D-01069 Dresden, Germany
3 shared publications - Andreas Leuteritz
Leibniz-Institut für Polymerforschung e. V. Dresden (IPF), Dresden, Germany
2 shared publications - Gert Heinrich
Leibniz-Institut für Polymerforschung Dresden e.V., Hohe Str. 6, 01069 Dresden, Germany
2 shared publications Ali Akbar Yousefi
Iran Polymer and Petrochemical Institute, P.O. Box 14965/115, Tehran, Iran
1 shared publication
Latest Publications
- Open Access
Barrier Properties of GnP–PA-Extruded Films
It is generally known that significant improvements in the properties of nanocomposites can be achieved with graphene types currently commercially available. However, so far this is only possible on a laboratory scale. Thus, the aim of this study was to transfer results from laboratory scale experiments to industrial processes. Therefore, nanocomposites based on polyamide (PA) and graphene nanoplatelets (GnP) were prepared in order to produce membranes with improved gas barrier properties, which are characterized by reduced permeation rates of helium. First, nanocomposites were prepared with different amounts of commercial availably graphene nanoplatelets using a semi-industrial-scale compounder. Subsequently, films were produced by compression molding at different temperatures, as well as by flat film extrusion. The extruded films were annealed at different temperatures and durations. In order to investigate the effect of thermal treatment on barrier properties in correlation to thermal, structural, and morphological properties, the films were characterized by differential scanning calorimetry (DSC), wide angle X-ray scattering (WAXS), optical microscopy (OM), transmission electron microscopy (TEM), melt rheology measurements, and permeation measurements. In addition to structural characterization, mechanical properties were investigated. The results demonstrate that the permeation rate is strongly influenced by the processing conditions and the filler content. If the filler content is increased, the permeation rate is reduced. The annealing process can further enhance this effect.
Open AccessBarrier Properties of GnP–PA-Extruded Films
It is generally known that significant improvements in the properties of nanocomposites can be achieved with graphene types currently commercially available. However, so far this is only possible on a laboratory scale. Thus, the aim of this study was to transfer results from laboratory scale experiments to industrial processes. Therefore, nanocomposites based on polyamide (PA) and graphene nanoplatelets (GnP) were prepared in order to produce membranes with improved gas barrier properties, which are characterized by reduced permeation rates of helium. First, nanocomposites were prepared with different amounts of commercial availably graphene nanoplatelets using a semi-industrial-scale compounder. Subsequently, films were produced by compression molding at different temperatures, as well as by flat film extrusion. The extruded films were annealed at different temperatures and durations. In order to investigate the effect of thermal treatment on barrier properties in correlation to thermal, structural, and morphological properties, the films were characterized by differential scanning calorimetry (DSC), wide angle X-ray scattering (WAXS), optical microscopy (OM), transmission electron microscopy (TEM), melt rheology measurements, and permeation measurements. In addition to structural characterization, mechanical properties were investigated. The results demonstrate that the permeation rate is strongly influenced by the processing conditions and the filler content. If the filler content is increased, the permeation rate is reduced. The annealing process can further enhance this effect.
- 10 February 2017
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 56 (15) , 1657-1664
Toughened Unsaturated Polyester Composites Reinforced with Slag Material
Slag powder, which is a by-product during the steel making process, has been utilized in this study. It was comminuted followed by stearic acid treatment. The mineralogical composition of the unmodified and modified slag was inspected using energy dispersive spectrophotometer. The effectiveness of the stearic acid treatment was followed by attenuated total reflectance infrared spectroscopy. The potential of unmodified and modified slag as reinforcement for unsaturated polyester mixed with solution of nitrile butadiene rubber to produce toughened polyester was evaluated. The toughened polyester has been fabricated by casting technique from solution state. The impact of unmodified and modified slag on the mechanical and thermal characteristics of the composites was inspected. The fire resistance of the composite was evaluated by exposing the composites to direct open flame. The fracture surfaces of the impacted samples were viewed under scanning electron microscope. This was done to obtain an idea on the dispersion pattern and the quality of bonding between the slag and the matrix.
- 10 February 2017
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 56 (15) , 1657-1664
Toughened Unsaturated Polyester Composites Reinforced with Slag Material
Slag powder, which is a by-product during the steel making process, has been utilized in this study. It was comminuted followed by stearic acid treatment. The mineralogical composition of the unmodified and modified slag was inspected using energy dispersive spectrophotometer. The effectiveness of the stearic acid treatment was followed by attenuated total reflectance infrared spectroscopy. The potential of unmodified and modified slag as reinforcement for unsaturated polyester mixed with solution of nitrile butadiene rubber to produce toughened polyester was evaluated. The toughened polyester has been fabricated by casting technique from solution state. The impact of unmodified and modified slag on the mechanical and thermal characteristics of the composites was inspected. The fire resistance of the composite was evaluated by exposing the composites to direct open flame. The fracture surfaces of the impacted samples were viewed under scanning electron microscope. This was done to obtain an idea on the dispersion pattern and the quality of bonding between the slag and the matrix.
- 1 December 2013
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 143 (1) , 360-366
Additive free thermoplastic vulcanizates based on natural rubber
- 1 December 2013
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 143 (1) , 360-366
Additive free thermoplastic vulcanizates based on natural rubber
- 24 April 2012
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 298 (1) , 113-126
Dynamic and Transient Shear Start‐Up Flow Experiments for Analyzing Nanoclay Localization in PP/PET Blends: Correlation with Microstructure
- 24 April 2012
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 298 (1) , 113-126
Dynamic and Transient Shear Start‐Up Flow Experiments for Analyzing Nanoclay Localization in PP/PET Blends: Correlation with Microstructure
- Open Access
- 12 April 2012
- Published by Hindawi Limited in International Journal of Chemical Engineering
- Vol. 2012 (4) , 1-5
Utilization of Agrowaste Polymers in PVC/NBR Alloys: Tensile, Thermal, and Morphological Properties
Poly(vinyl chloride)/nitrile butadiene rubber (PVC/NBR) alloys were melt-mixed using a Brabender Plasticorder at 180∘C and 50rpm rotor speed. Alloys obtained by melt mixing from PVC and NBR were formulated with wood-flour- (WF-) based olive residue, a natural byproduct from olive oil extraction industry. WF was progressively increased from 0 to 30phr. The effects of WF loadings on the tensile properties of the fabricated samples were inspected. The torque rheometry, which is an indirect indication of the melt strength, is reported. The pattern of water uptake for the composites was checked as a function WF loading. The fracture mode and the quality of bonding of the alloy with and without filler are studied using electron scanning microscope (SEM).
- 12 April 2012
- Published by Hindawi Limited in International Journal of Chemical Engineering
- Vol. 2012 (4) , 1-5
Open AccessUtilization of Agrowaste Polymers in PVC/NBR Alloys: Tensile, Thermal, and Morphological Properties
Poly(vinyl chloride)/nitrile butadiene rubber (PVC/NBR) alloys were melt-mixed using a Brabender Plasticorder at 180∘C and 50rpm rotor speed. Alloys obtained by melt mixing from PVC and NBR were formulated with wood-flour- (WF-) based olive residue, a natural byproduct from olive oil extraction industry. WF was progressively increased from 0 to 30phr. The effects of WF loadings on the tensile properties of the fabricated samples were inspected. The torque rheometry, which is an indirect indication of the melt strength, is reported. The pattern of water uptake for the composites was checked as a function WF loading. The fracture mode and the quality of bonding of the alloy with and without filler are studied using electron scanning microscope (SEM).
- 13 March 2012
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 213 (7) , 729-737
In Situ Modification of Unmodified Montmorillonite in Polypropylene by Electron‐Induced Reactive Processing
- 13 March 2012
- Published by Wiley in Macromolecular Chemistry and Physics
- Vol. 213 (7) , 729-737
In Situ Modification of Unmodified Montmorillonite in Polypropylene by Electron‐Induced Reactive Processing
- 17 March 2011
- Published by Wiley in Macromolecular Symposia
- Vol. 301 (1) , 146-150
Modification of Particle Filled Polymers with High Energy Electrons Under In-Stationary Conditions of Melt Mixing
- 17 March 2011
- Published by Wiley in Macromolecular Symposia
- Vol. 301 (1) , 146-150
Modification of Particle Filled Polymers with High Energy Electrons Under In-Stationary Conditions of Melt Mixing
- 29 October 2008
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 80 (11) , 1683-1699
Polymere Nanokomposite mit anorganischen Funktionsfüllstoffen
Polymer/Partikel‐Nanokomposite sind eine Stoffklasse, die seit ca. 15 Jahren intensives Interesse in Forschung und Industrie gefunden hat. Neben erfolgreichen Anwendungen sind auch eine Reihe der ursprünglichen Erwartungen nicht erfüllt oder erfordern noch erheblichen Entwicklungsaufwand. Beispielgebend werden für drei der wichtigsten Füllstoffgruppen –Schichtsilicate, Kohlenstoff‐Nanoröhren und Layered Double Hydroxides – die Füllstoffe selbst, die Herstellung und die Eigenschaften der Nanokomposite sowie deren Anwendungspotenzial dargestellt.
- 29 October 2008
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 80 (11) , 1683-1699
Polymere Nanokomposite mit anorganischen Funktionsfüllstoffen
Polymer/Partikel‐Nanokomposite sind eine Stoffklasse, die seit ca. 15 Jahren intensives Interesse in Forschung und Industrie gefunden hat. Neben erfolgreichen Anwendungen sind auch eine Reihe der ursprünglichen Erwartungen nicht erfüllt oder erfordern noch erheblichen Entwicklungsaufwand. Beispielgebend werden für drei der wichtigsten Füllstoffgruppen –Schichtsilicate, Kohlenstoff‐Nanoröhren und Layered Double Hydroxides – die Füllstoffe selbst, die Herstellung und die Eigenschaften der Nanokomposite sowie deren Anwendungspotenzial dargestellt.