Marko Vauhkonen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marko Vauhkonen has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Jari P. Kaipio
Department of Mathematics, University of Auckland, Auckland, New Zealand
7 shared publications L M Heikkinen
4 shared publicationsJ P Kaipio
3 shared publicationsT. Savolainen
Department of Applied Physics , University of Kuopio , P.O. Box 1627, Kuopio, FIN-70211, Finland
3 shared publicationsP J Vauhkonen
2 shared publicationsT Savolainen
2 shared publications
Latest Publications
- 23 December 2013
- Published by Taylor & Francis in Inverse Problems in Science and Engineering
- Vol. 22 (8) , 1259-1284
Reduced forward models in electrical impedance tomography with probe geometry
- 23 December 2013
- Published by Taylor & Francis in Inverse Problems in Science and Engineering
- Vol. 22 (8) , 1259-1284
Reduced forward models in electrical impedance tomography with probe geometry
- 18 January 2011
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 22 (2)
A reduced-order filtering approach for 3D dynamical electrical impedance tomography
- 18 January 2011
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 22 (2)
A reduced-order filtering approach for 3D dynamical electrical impedance tomography
- 20 February 2005
- Published by Optica Publishing Group in Applied Optics
- Vol. 44 (6) , 876-886
Hybrid radiative-transfer–diffusion model for optical tomography
A hybrid radiative-transfer–diffusion model for optical tomography is proposed. The light propagation is modeled with the radiative-transfer equation in the vicinity of the laser sources, and the diffusion approximation is used elsewhere in the domain. The solution of the radiative-transfer equation is used to construct a Dirichlet boundary condition for the diffusion approximation on a fictitious interface within the object. This boundary condition constitutes an approximative distributed source model for the diffusion approximation in the remaining area. The results from the proposed approach are compared with finite-element solutions of the radiative-transfer equation and the diffusion approximation and Monte Carlo simulation. The results show that the method improves the accuracy of the forward model compared with the conventional diffusion model.
- 20 February 2005
- Published by Optica Publishing Group in Applied Optics
- Vol. 44 (6) , 876-886
Hybrid radiative-transfer–diffusion model for optical tomography
A hybrid radiative-transfer–diffusion model for optical tomography is proposed. The light propagation is modeled with the radiative-transfer equation in the vicinity of the laser sources, and the diffusion approximation is used elsewhere in the domain. The solution of the radiative-transfer equation is used to construct a Dirichlet boundary condition for the diffusion approximation on a fictitious interface within the object. This boundary condition constitutes an approximative distributed source model for the diffusion approximation in the remaining area. The results from the proposed approach are compared with finite-element solutions of the radiative-transfer equation and the diffusion approximation and Monte Carlo simulation. The results show that the method improves the accuracy of the forward model compared with the conventional diffusion model.
- 17 June 2004
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 15 (7) , 1402-1411
Estimating shapes and free surfaces with electrical impedance tomography
- 17 June 2004
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 15 (7) , 1402-1411
Estimating shapes and free surfaces with electrical impedance tomography
- 18 July 2001
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 12 (8) , 1012-1019
Modelling of internal structures and electrodes in electrical process tomography
- 18 July 2001
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 12 (8) , 1012-1019
Modelling of internal structures and electrodes in electrical process tomography
- 18 July 2001
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 12 (8) , 1032-1039
Image reconstruction in time-varying electrical impedance tomography based on the extended Kalman filter
- 18 July 2001
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 12 (8) , 1032-1039
Image reconstruction in time-varying electrical impedance tomography based on the extended Kalman filter
- 1 May 2001
- Published by Taylor & Francis in Inverse Problems in Engineering
- Vol. 9 (5) , 431-454
Electrical process tomography with known internal structures and resistivities
In process tomography the aim is to obtain information typically from the interior of the process vessels based on the measurements made on the surface of the vessel. Electrical impedance tomography (EIT) is an imaging modality in which the internal resistivity distribution is reconstructed based on the known injected currents and measured voltages on the surface. Since the reconstructed image represents the resistivity distribution of the interior, certain internal structures such as highly conductive mixing paddles in a stirred vessel may entail difficulties in the image reconstruction. This is because EIT is a diffuse, nonlinear imaging modality which makes it difficult to reconstruct high contrasts in the internal resistivity distribution. In this paper the effects of internal conductive structures on the reconstructed images in two-dimensional cases are considered and possible improvements in the reconstructions by taking into account the locations and resistivities of these structures are studied. It is shown that in some internal conductive structure geometries the prior information of the structure may improve the reconstructions substantially. However, it is also shown that in a case in which the conductive structure encloses the region of interest by creating a low-resistivity path for current to flow, the proper reconstruction is impossible even with prior information of the structure.
- 1 May 2001
- Published by Taylor & Francis in Inverse Problems in Engineering
- Vol. 9 (5) , 431-454
Electrical process tomography with known internal structures and resistivities
In process tomography the aim is to obtain information typically from the interior of the process vessels based on the measurements made on the surface of the vessel. Electrical impedance tomography (EIT) is an imaging modality in which the internal resistivity distribution is reconstructed based on the known injected currents and measured voltages on the surface. Since the reconstructed image represents the resistivity distribution of the interior, certain internal structures such as highly conductive mixing paddles in a stirred vessel may entail difficulties in the image reconstruction. This is because EIT is a diffuse, nonlinear imaging modality which makes it difficult to reconstruct high contrasts in the internal resistivity distribution. In this paper the effects of internal conductive structures on the reconstructed images in two-dimensional cases are considered and possible improvements in the reconstructions by taking into account the locations and resistivities of these structures are studied. It is shown that in some internal conductive structure geometries the prior information of the structure may improve the reconstructions substantially. However, it is also shown that in a case in which the conductive structure encloses the region of interest by creating a low-resistivity path for current to flow, the proper reconstruction is impossible even with prior information of the structure.
- 10 February 2001
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 50 (4) , 809-824
Boundary element method and internal electrodes in electrical impedance tomography
- 10 February 2001
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 50 (4) , 809-824
Boundary element method and internal electrodes in electrical impedance tomography
- 1 February 2001
- Published by IOP Publishing in Physiological Measurement
- Vol. 22 (1) , 107-111
A MATLAB package for the EIDORS project to reconstruct two-dimensional EIT images
The EIDORS (electrical impedance and diffuse optical reconstruction software) project aims to produce a software system for reconstructing images from electrical or diffuse optical data. MATLAB is a software that is used in the EIDORS project for rapid prototyping, graphical user interface construction and image display. We have written a MATLAB package (http://venda.uku.fi/ vauhkon/) which can be used for two-dimensional mesh generation, solving the forward problem and reconstructing and displaying the reconstructed images (resistivity or admittivity). In this paper we briefly describe the mathematical theory on which the codes are based on and also give some examples of the capabilities of the package.
- 1 February 2001
- Published by IOP Publishing in Physiological Measurement
- Vol. 22 (1) , 107-111
A MATLAB package for the EIDORS project to reconstruct two-dimensional EIT images
The EIDORS (electrical impedance and diffuse optical reconstruction software) project aims to produce a software system for reconstructing images from electrical or diffuse optical data. MATLAB is a software that is used in the EIDORS project for rapid prototyping, graphical user interface construction and image display. We have written a MATLAB package (http://venda.uku.fi/ vauhkon/) which can be used for two-dimensional mesh generation, solving the forward problem and reconstructing and displaying the reconstructed images (resistivity or admittivity). In this paper we briefly describe the mathematical theory on which the codes are based on and also give some examples of the capabilities of the package.
- 1 August 2000
- Published by IOP Publishing in Inverse Problems
- Vol. 16 (4) , 1079
A finite-element model of electron transport in radiation therapy and a related inverse problem
- 1 August 2000
- Published by IOP Publishing in Inverse Problems
- Vol. 16 (4) , 1079
A finite-element model of electron transport in radiation therapy and a related inverse problem