Chong Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Chong Liu has a total of 223 co-authors. Here are the top co-authors by number of shared publications:
- Dong Liu
Zhejiang University
29 shared publications Bin Liu
Changzhou Inno Laser Technology Corporation Limited
16 shared publicationsXiaoyan Qiu
14 shared publications- Miao Hu
Hangzhou Dianzi University
13 shared publications Junyang Dong
12 shared publicationsZhibin Ye
Quzhou University
12 shared publications
Latest Publications
- 4 August 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (16) , 30106
Wavefront pre-compensation in a 302-W single-frequency solid-state amplifier via multistage equivalent aberration mapping
High-power single-frequency lasers with excellent beam quality are increasingly demanded across a wide range of applications. Thermally induced aberrations remain a major obstacle to power scaling in single-frequency solid-state amplifiers. In this work, a wavefront pre-compensation architecture for a high-power single-frequency solid-state master oscillator power amplifier (MOPA) system is proposed and experimentally demonstrated. To compensate aberrations generated by spatially separated amplifier stages, a multistage equivalent aberration mapping framework combined with sequential optimization is developed, allowing unified correction with a single spatial light modulator (SLM). Based on this architecture, a 1064 nm single-frequency solid-state laser delivers 302 W of output power with a measured linewidth of 6.8 kHz. The beam quality factor M 2 is improved from 1.86 to 1.25, while the focal spot quality is significantly enhanced. These results demonstrate the feasibility of adaptive wavefront pre-compensation in high-power multistage solid-state amplifiers and highlight its potential for power scaling beyond the nonlinear limitations of fiber lasers.
- 4 August 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (16) , 30106
Wavefront pre-compensation in a 302-W single-frequency solid-state amplifier via multistage equivalent aberration mapping
High-power single-frequency lasers with excellent beam quality are increasingly demanded across a wide range of applications. Thermally induced aberrations remain a major obstacle to power scaling in single-frequency solid-state amplifiers. In this work, a wavefront pre-compensation architecture for a high-power single-frequency solid-state master oscillator power amplifier (MOPA) system is proposed and experimentally demonstrated. To compensate aberrations generated by spatially separated amplifier stages, a multistage equivalent aberration mapping framework combined with sequential optimization is developed, allowing unified correction with a single spatial light modulator (SLM). Based on this architecture, a 1064 nm single-frequency solid-state laser delivers 302 W of output power with a measured linewidth of 6.8 kHz. The beam quality factor M 2 is improved from 1.86 to 1.25, while the focal spot quality is significantly enhanced. These results demonstrate the feasibility of adaptive wavefront pre-compensation in high-power multistage solid-state amplifiers and highlight its potential for power scaling beyond the nonlinear limitations of fiber lasers.
- 1 August 2026
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 65 (08) , 1-11
Inter-stage spherical aberration self-compensation for beam quality improvement in high-power multistage laser amplifiers
In high-power end-pumped solid-state laser amplifiers, spherical aberration (SA) self-compensation can improve beam quality, but its operational boundaries remain unclear. A numerical model is established to characterize optical field evolution inside an end-pumped crystal and free space. Experiments confirm that the positive SA evolves into negative SA beyond the beam waist. Optimizing the latter-stage incident diameter in a two-stage amplifier, simultaneous power scaling and beam quality improvement are achieved via SA self-compensation. At 15-W seed laser power and 1.1-mm second-stage incident diameter, the system achieves 136.7 W output power with an M2 factor of 1.42, superior to the first-stage value of 1.76. Furthermore, increasing seed power expands the compensable incident diameter range, with average power extraction efficiency over 40% and an optimized M2 factor of 1.50. This approach provides a promising solution for beam quality management in kilowatt-class laser systems.
- 1 August 2026
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 65 (08) , 1-11
Inter-stage spherical aberration self-compensation for beam quality improvement in high-power multistage laser amplifiers
In high-power end-pumped solid-state laser amplifiers, spherical aberration (SA) self-compensation can improve beam quality, but its operational boundaries remain unclear. A numerical model is established to characterize optical field evolution inside an end-pumped crystal and free space. Experiments confirm that the positive SA evolves into negative SA beyond the beam waist. Optimizing the latter-stage incident diameter in a two-stage amplifier, simultaneous power scaling and beam quality improvement are achieved via SA self-compensation. At 15-W seed laser power and 1.1-mm second-stage incident diameter, the system achieves 136.7 W output power with an M2 factor of 1.42, superior to the first-stage value of 1.76. Furthermore, increasing seed power expands the compensable incident diameter range, with average power extraction efficiency over 40% and an optimized M2 factor of 1.50. This approach provides a promising solution for beam quality management in kilowatt-class laser systems.
- 29 June 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (21) , 7178
PWD: Polarization-based Waveform Decomposition method for airborne lidar bathymetry in very shallow waters
Airborne lidar provides high-accuracy, efficient, and continuous mapping of land and seafloor topography in nearshore and island regions. However, accurate retrieval of very shallow water depths is hindered by the mixing of lidar signals from the surface and bottom. Here, we propose a polarization-based waveform decomposition method (PWD) to achieve land–sea topographic detection. By exploiting the polarization differences between the water surface and bottom, this method jointly uses the co-polarized and cross-polarized channels to estimate the initial positions. Subsequently, a waveform decomposition method is employed to separate the water surface and bottom signals from mixed waveforms, enabling accurate water depth retrieval. The accuracy and robustness of this method were validated through field experimental data obtained by airborne lidar. The results demonstrate that the water depth retrieved by the PWD method shows strong consistency with the results from the benchmark green/NIR method, with a root mean square relative deviation (RMSRD) of 13.67% and a coefficient of determination (R 2 ) of 0.9190. This method provides a new pathway, to our knowledge, for efficient integrated land–sea surveying, supplying reliable data for terrain detection and environmental monitoring.
- 29 June 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (21) , 7178
PWD: Polarization-based Waveform Decomposition method for airborne lidar bathymetry in very shallow waters
Airborne lidar provides high-accuracy, efficient, and continuous mapping of land and seafloor topography in nearshore and island regions. However, accurate retrieval of very shallow water depths is hindered by the mixing of lidar signals from the surface and bottom. Here, we propose a polarization-based waveform decomposition method (PWD) to achieve land–sea topographic detection. By exploiting the polarization differences between the water surface and bottom, this method jointly uses the co-polarized and cross-polarized channels to estimate the initial positions. Subsequently, a waveform decomposition method is employed to separate the water surface and bottom signals from mixed waveforms, enabling accurate water depth retrieval. The accuracy and robustness of this method were validated through field experimental data obtained by airborne lidar. The results demonstrate that the water depth retrieved by the PWD method shows strong consistency with the results from the benchmark green/NIR method, with a root mean square relative deviation (RMSRD) of 13.67% and a coefficient of determination (R 2 ) of 0.9190. This method provides a new pathway, to our knowledge, for efficient integrated land–sea surveying, supplying reliable data for terrain detection and environmental monitoring.
- 1 June 2026
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 65 (06) , 1-11
High-precision optical field simulation for end-pumped laser amplifiers using a seed beam reconstruction approach
A simulation model is proposed to explore the evolution of the optical field in a three-stage end-pumped laser amplifier, utilizing a seed beam reconstructed in terms of both intensity and wavefront. Experimental validation demonstrates the efficacy of the proposed reconstruction scheme through direct comparison with an ideal Gaussian seed model. The reconstructed model exhibits superior accuracy in replicating the optical field evolution dynamics, particularly in multistage master oscillator power amplifier (MOPA) configurations where the Gaussian approximation fails to maintain simulation fidelity. This advancement significantly elevates the theoretical precision of MOPA laser system modeling, providing key theoretical guidance for the simulation analysis and overall design of high-power MOPA laser systems.
- 1 June 2026
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 65 (06) , 1-11
High-precision optical field simulation for end-pumped laser amplifiers using a seed beam reconstruction approach
A simulation model is proposed to explore the evolution of the optical field in a three-stage end-pumped laser amplifier, utilizing a seed beam reconstructed in terms of both intensity and wavefront. Experimental validation demonstrates the efficacy of the proposed reconstruction scheme through direct comparison with an ideal Gaussian seed model. The reconstructed model exhibits superior accuracy in replicating the optical field evolution dynamics, particularly in multistage master oscillator power amplifier (MOPA) configurations where the Gaussian approximation fails to maintain simulation fidelity. This advancement significantly elevates the theoretical precision of MOPA laser system modeling, providing key theoretical guidance for the simulation analysis and overall design of high-power MOPA laser systems.
- 24 April 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (13) , 4369
96 W, 4.8 mJ Yb:YAG rod-type picosecond laser amplifier using a thermally induced birefringence compensation method for extraction efficiency enhancement
We demonstrate a cost-effective and compact chirped pulse amplification (CPA) picosecond laser system with high average power and pulse energy. Based on four Yb:YAG rods, the amplifier produces 5.1 mJ pulses at 102 W average power. The initial output beam quality M 2 factor was measured to be 1.33, which was further improved to 1.09 by spherical aberration compensation. The amplified pulses were compressed to a duration of 1 ps with an efficiency exceeding 93%. An improved dual-rod cascaded compensation method for thermally induced birefringence was implemented in the high-energy Yb:YAG amplifier, reducing the depolarization loss to 0.29% at 102 W output power while enhancing the extraction efficiency.
- 24 April 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (13) , 4369
96 W, 4.8 mJ Yb:YAG rod-type picosecond laser amplifier using a thermally induced birefringence compensation method for extraction efficiency enhancement
We demonstrate a cost-effective and compact chirped pulse amplification (CPA) picosecond laser system with high average power and pulse energy. Based on four Yb:YAG rods, the amplifier produces 5.1 mJ pulses at 102 W average power. The initial output beam quality M 2 factor was measured to be 1.33, which was further improved to 1.09 by spherical aberration compensation. The amplified pulses were compressed to a duration of 1 ps with an efficiency exceeding 93%. An improved dual-rod cascaded compensation method for thermally induced birefringence was implemented in the high-energy Yb:YAG amplifier, reducing the depolarization loss to 0.29% at 102 W output power while enhancing the extraction efficiency.
- 1 April 2026
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 65 (04) , 1-10
Low-thermal-effect Nd:YVO4 picosecond laser amplifier achieving 302.2 W output with near-diffraction-limited beam quality
This study presents an efficient, high-power, high-beam-quality Nd:YVO4 laser amplifier end-pumped with 888 nm laser diodes. A 24 W, 5 MHz, 8.2 ps, 1064 nm seed laser was amplified to 302.2 W in a three-stage Nd:YVO4 amplifier, achieving a total extraction efficiency of 44.0%. By mitigating the impact of thermal effects in the first amplification stage and implementing low-thermal-effect design strategies in the second and third amplification stages, the beam quality of the amplifier was effectively maintained. Without additional compensation components, the beam quality factor remained below 1.3 and was further improved to below 1.2 with the introduction of a spherical aberration phase plate. Frequency conversion in an LBO crystal generated 210.7 W of 532 nm laser with a beam quality factor of 1.02. These results demonstrate that a properly designed thermal management strategy can provide a practical alternative to complex active compensation in high-average-power, high-brightness picosecond laser systems.
- 1 April 2026
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 65 (04) , 1-10
Low-thermal-effect Nd:YVO4 picosecond laser amplifier achieving 302.2 W output with near-diffraction-limited beam quality
This study presents an efficient, high-power, high-beam-quality Nd:YVO4 laser amplifier end-pumped with 888 nm laser diodes. A 24 W, 5 MHz, 8.2 ps, 1064 nm seed laser was amplified to 302.2 W in a three-stage Nd:YVO4 amplifier, achieving a total extraction efficiency of 44.0%. By mitigating the impact of thermal effects in the first amplification stage and implementing low-thermal-effect design strategies in the second and third amplification stages, the beam quality of the amplifier was effectively maintained. Without additional compensation components, the beam quality factor remained below 1.3 and was further improved to below 1.2 with the introduction of a spherical aberration phase plate. Frequency conversion in an LBO crystal generated 210.7 W of 532 nm laser with a beam quality factor of 1.02. These results demonstrate that a properly designed thermal management strategy can provide a practical alternative to complex active compensation in high-average-power, high-brightness picosecond laser systems.
- Open Access
- 24 March 2026
- Published by Cambridge University Press (CUP) in High Power Laser Science and Engineering
- Vol. 14, 1-26
Multimodal detection and laser-induced damage correlation of real surface defects on fused silica optics
Surface defects on fused silica optics significantly limit their laser-induced damage resistance under ultraviolet pulsed laser irradiation, yet quantitative correlations between defect parameters and damage thresholds remain scarce. This study is the first to perform multimodal detection and correlation analysis of laser-induced damage initiated at real defects on fused silica. Scratches were characterized by scattered light intensity, width and fluorescence intensity, and correlated with the damage-onset fluence (DOF). Results show trailing indent scratches (1.9–8.8 μm wide) have DOFs of 1.27–13.2 J/cm 2 , while plastic continuous scratches (0.4–5.8 μm wide) exhibit higher DOFs of 12.3– 22.0 J/cm 2 . Fluorescence intensity strongly negatively correlates with DOF ( p < 0.001), as do scratch width and fluorescence intensity at α = 0.01 ( p < 0.01). These findings establish scratch width and fluorescence intensity as quantitative damage precursors, advancing surface quality assessment for high-energy laser optics.
- 24 March 2026
- Published by Cambridge University Press (CUP) in High Power Laser Science and Engineering
- Vol. 14, 1-26
Open AccessMultimodal detection and laser-induced damage correlation of real surface defects on fused silica optics
Surface defects on fused silica optics significantly limit their laser-induced damage resistance under ultraviolet pulsed laser irradiation, yet quantitative correlations between defect parameters and damage thresholds remain scarce. This study is the first to perform multimodal detection and correlation analysis of laser-induced damage initiated at real defects on fused silica. Scratches were characterized by scattered light intensity, width and fluorescence intensity, and correlated with the damage-onset fluence (DOF). Results show trailing indent scratches (1.9–8.8 μm wide) have DOFs of 1.27–13.2 J/cm 2 , while plastic continuous scratches (0.4–5.8 μm wide) exhibit higher DOFs of 12.3– 22.0 J/cm 2 . Fluorescence intensity strongly negatively correlates with DOF ( p < 0.001), as do scratch width and fluorescence intensity at α = 0.01 ( p < 0.01). These findings establish scratch width and fluorescence intensity as quantitative damage precursors, advancing surface quality assessment for high-energy laser optics.
- Open Access
- 18 March 2026
- Published by Cambridge University Press (CUP) in High Power Laser Science and Engineering
- Vol. 14
Near-diffraction-limited femtosecond laser based on ytterbium-doped yttrium aluminum garnet rod-type amplifiers with approximately 500 W average power and more than 50% power extraction efficiency
A high-power, efficient pulsed amplifier based on a laser diode end-pumped ytterbium-doped yttrium aluminum garnet (Yb:YAG) rod was demonstrated. The crystal’s reabsorption was effectively minimized by optimizing the amplifier’s parameters through numerical simulations, leading to a power extraction efficiency of up to 56%. A compensation method was applied to correct the beam distortion caused by thermally induced birefringence in the Yb:YAG rod. Furthermore, a remarkably low depolarization rate of 2.2% was achieved, along with an average power output of 483 W. The beam quality factor ( M 2 ) of the amplified signal was improved to below 1.3, following compensation of the thermally induced spherical aberration using a phase plate. To the best of our knowledge, this achievement represents the highest average power and efficiency for fundamental mode operation in an Yb:YAG rod amplifier at room temperature.
- 18 March 2026
- Published by Cambridge University Press (CUP) in High Power Laser Science and Engineering
- Vol. 14
Open AccessNear-diffraction-limited femtosecond laser based on ytterbium-doped yttrium aluminum garnet rod-type amplifiers with approximately 500 W average power and more than 50% power extraction efficiency
A high-power, efficient pulsed amplifier based on a laser diode end-pumped ytterbium-doped yttrium aluminum garnet (Yb:YAG) rod was demonstrated. The crystal’s reabsorption was effectively minimized by optimizing the amplifier’s parameters through numerical simulations, leading to a power extraction efficiency of up to 56%. A compensation method was applied to correct the beam distortion caused by thermally induced birefringence in the Yb:YAG rod. Furthermore, a remarkably low depolarization rate of 2.2% was achieved, along with an average power output of 483 W. The beam quality factor ( M 2 ) of the amplified signal was improved to below 1.3, following compensation of the thermally induced spherical aberration using a phase plate. To the best of our knowledge, this achievement represents the highest average power and efficiency for fundamental mode operation in an Yb:YAG rod amplifier at room temperature.
- 4 March 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (8) , 2661-2671
Capability assessment of airborne lidar for underwater target detection
Oceanic lidar shows significant potential for efficient and accurate bathymetric measurements at both day and night. However, its performance is constrained by the receiver field of view (FOV) and seawater optical properties, due to signal attenuation, background noise, and beam broadening. Quantitative analyses remain limited, owing to the complex geometric interactions between targets and the laser footprint. This study simulates return signals of six typical targets with varying sizes and shapes under different water conditions to systematically evaluate the effects of FOV, target size, target shape, and chlorophyll concentration on lidar detection performance. Results indicate that larger targets and lower chlorophyll concentrations yield greater maximum detection depths, while increasing the FOV produces a non-monotonic effect. The influence of target shape is minimal when the target is centered on the laser footprint. In oligotrophic, mesotrophic, and eutrophic waters, the maximum detection depths of the six targets range from 72.0∼196.2m, 21.5∼96.5m, and 14.9∼35.9m, with corresponding maximum detection errors of 0.08∼1.09m, 0.09∼2.50m, and 0.11∼2.67m. These findings provide quantitative guidance for system parameter design, offering a theoretical basis for effective airborne lidar target detection in real water environments.
- 4 March 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (8) , 2661-2671
Capability assessment of airborne lidar for underwater target detection
Oceanic lidar shows significant potential for efficient and accurate bathymetric measurements at both day and night. However, its performance is constrained by the receiver field of view (FOV) and seawater optical properties, due to signal attenuation, background noise, and beam broadening. Quantitative analyses remain limited, owing to the complex geometric interactions between targets and the laser footprint. This study simulates return signals of six typical targets with varying sizes and shapes under different water conditions to systematically evaluate the effects of FOV, target size, target shape, and chlorophyll concentration on lidar detection performance. Results indicate that larger targets and lower chlorophyll concentrations yield greater maximum detection depths, while increasing the FOV produces a non-monotonic effect. The influence of target shape is minimal when the target is centered on the laser footprint. In oligotrophic, mesotrophic, and eutrophic waters, the maximum detection depths of the six targets range from 72.0∼196.2m, 21.5∼96.5m, and 14.9∼35.9m, with corresponding maximum detection errors of 0.08∼1.09m, 0.09∼2.50m, and 0.11∼2.67m. These findings provide quantitative guidance for system parameter design, offering a theoretical basis for effective airborne lidar target detection in real water environments.