Fernando Antônio Medeiros Marinho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Fernando Antônio Medeiros Marinho has a total of 93 co-authors. Here are the top co-authors by number of shared publications:
- Orlando Martini de Oliveira
Federal Univ. of Santa Catarina
5 shared publications - Gilson de Farias Neves Gitirana
Universidade Federal de Goiás
3 shared publications - Rafael Augusto dos Reis Higashi
Universidade Federal de Santa Catarina
3 shared publications - Rodolfo Moreda Mendes
Universidade do Vale do Paraiba – UNIVAP
3 shared publications - Alessander Christopher Morales Kormann
Universidade Federal do Paraná
2 shared publications - Alessandro Tarantino
Department of Civil and Environmental Engineering, University of Strathclyde, Glasgow, U.K.
2 shared publications
Latest Publications
- Open Access
- 25 October 2026
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 49 (4)
Field measurement of hydraulic conductivity in a compacted filtered iron ore tailings stack using mini-infiltrometer tests
This paper presents a field-based assessment of near-surface hydraulic conductivity in a compacted filtered iron ore tailings stack using mini-infiltrometer tests. A total of 115 in situ measurements were performed on the compacted surface, providing a dataset for evaluating the variability of near-surface field measurements under controlled suction conditions. The mini-infiltrometer results are interpreted as hydraulic conductivity values associated with the pressure head applied at the porous disk–tailings interface, not necessarily as fully saturated hydraulic conductivity. The measured values ranged from 1.14 × 10−7 m/s to 4.59 × 10−6 m/s, with an arithmetic mean of 1.31 × 10−6 m/s, a median of 1.20 × 10−6 m/s, and a geometric mean of 1.12 × 10−6 m/s. Although the results were concentrated around 10−6 m/s, the coefficient of variation was approximately 56.9%, indicating relevant relative variability. Most values were located between 5.0 × 10−7 m/s and 3.0 × 10−6 m/s, supporting the use of the geometric mean as a representative central estimate for engineering analyses. The influence of imposed suction (h0 ) was also examined; however, no systematic dependence on the applied values was identified. Comparison with published data shows that the results fall within the range reported for compacted and filtered tailings, while reinforcing that hydraulic conductivity cannot be inferred from void ratio alone. The study highlights the importance of direct field measurements for supporting seepage analyses, transient flow modelling, water balance assessments, and hydraulic characterization of filtered tailings stacks.
- 25 October 2026
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 49 (4)
Open AccessField measurement of hydraulic conductivity in a compacted filtered iron ore tailings stack using mini-infiltrometer tests
This paper presents a field-based assessment of near-surface hydraulic conductivity in a compacted filtered iron ore tailings stack using mini-infiltrometer tests. A total of 115 in situ measurements were performed on the compacted surface, providing a dataset for evaluating the variability of near-surface field measurements under controlled suction conditions. The mini-infiltrometer results are interpreted as hydraulic conductivity values associated with the pressure head applied at the porous disk–tailings interface, not necessarily as fully saturated hydraulic conductivity. The measured values ranged from 1.14 × 10−7 m/s to 4.59 × 10−6 m/s, with an arithmetic mean of 1.31 × 10−6 m/s, a median of 1.20 × 10−6 m/s, and a geometric mean of 1.12 × 10−6 m/s. Although the results were concentrated around 10−6 m/s, the coefficient of variation was approximately 56.9%, indicating relevant relative variability. Most values were located between 5.0 × 10−7 m/s and 3.0 × 10−6 m/s, supporting the use of the geometric mean as a representative central estimate for engineering analyses. The influence of imposed suction (h0 ) was also examined; however, no systematic dependence on the applied values was identified. Comparison with published data shows that the results fall within the range reported for compacted and filtered tailings, while reinforcing that hydraulic conductivity cannot be inferred from void ratio alone. The study highlights the importance of direct field measurements for supporting seepage analyses, transient flow modelling, water balance assessments, and hydraulic characterization of filtered tailings stacks.
- Open Access
- 1 December 2025
- Published by RGSA- Revista de Gestao Social e Ambiental in Revista de Gestão Social e Ambiental
- Vol. 19 (12) , e014103
Propozed Governance Model for The Closure of Mining Tailings Dams
Objective: To propose a governance model for the closure of tailings dams, structured around four criteria - Technical, Governance, Participation & Transparency, and Compliance — each composed of subcriteria detailing the critical activities required for conducting the process. Theoretical Framework: The failures of tailings dams in 2015 and 2019 led to the approval of increasingly restrictive legislation, such as Law No. 14,066/2020, which amended the National Dam Safety Policy (Law No. 12,334/2010), and the resolutions of the Agência Nacional de Mineração (ANM) No. 95/2022, 130/2023, and 175/2024. However, practical experience has shown that a closure process cannot be reduced to a legal obligation or viewed solely as a technical issue. Method: The development of the governance model was based on a bibliographic and documentary review of public policies, Brazilian dam safety legislation, ANM resolutions, and documents from various related entities, in addition to consulting international guidelines and global references for tailings dam management. All the references reviewed converge on the understanding that a closure process must be assessed from a multidimensional perspective, combining technical, governance, transparency, and regulatory compliance aspects. Results and Discussion: Despite the wide range of regulations on dam closure, Brazil still lacks a structured model that allows for the assessment of governance in closure processes in a way that is comparable to best practices and global experiences, ensuring both technical quality and social transparency. Research Implications: The proposed governance model represents an innovative tool for public managers, mining companies, regulatory agencies, and researchers, enabling a comparable and transparent evaluation of closure processes, thereby strengthening trust among the involved stakeholders. Originality/Value: The proposed model can be used as a management or audit tool, making the closure process more transparent and aligned with national and international best practices. Furthermore, it can serve as a comparative basis to monitor the evolution of governance over time or to evaluate governance performance in the closure of different dams.
- 1 December 2025
- Published by RGSA- Revista de Gestao Social e Ambiental in Revista de Gestão Social e Ambiental
- Vol. 19 (12) , e014103
Open AccessPropozed Governance Model for The Closure of Mining Tailings Dams
Objective: To propose a governance model for the closure of tailings dams, structured around four criteria - Technical, Governance, Participation & Transparency, and Compliance — each composed of subcriteria detailing the critical activities required for conducting the process. Theoretical Framework: The failures of tailings dams in 2015 and 2019 led to the approval of increasingly restrictive legislation, such as Law No. 14,066/2020, which amended the National Dam Safety Policy (Law No. 12,334/2010), and the resolutions of the Agência Nacional de Mineração (ANM) No. 95/2022, 130/2023, and 175/2024. However, practical experience has shown that a closure process cannot be reduced to a legal obligation or viewed solely as a technical issue. Method: The development of the governance model was based on a bibliographic and documentary review of public policies, Brazilian dam safety legislation, ANM resolutions, and documents from various related entities, in addition to consulting international guidelines and global references for tailings dam management. All the references reviewed converge on the understanding that a closure process must be assessed from a multidimensional perspective, combining technical, governance, transparency, and regulatory compliance aspects. Results and Discussion: Despite the wide range of regulations on dam closure, Brazil still lacks a structured model that allows for the assessment of governance in closure processes in a way that is comparable to best practices and global experiences, ensuring both technical quality and social transparency. Research Implications: The proposed governance model represents an innovative tool for public managers, mining companies, regulatory agencies, and researchers, enabling a comparable and transparent evaluation of closure processes, thereby strengthening trust among the involved stakeholders. Originality/Value: The proposed model can be used as a management or audit tool, making the closure process more transparent and aligned with national and international best practices. Furthermore, it can serve as a comparative basis to monitor the evolution of governance over time or to evaluate governance performance in the closure of different dams.
- Open Access
- 21 July 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (3)
Advances in unsaturated soils mechanics and technology in Brazil
Unsaturated soils mechanics (USM) and unsaturated soils technology (UST) have been the subject of great interest to Brazilian researchers and practitioners since the inception of the Brazilian Association for Soil Mechanics and Geotechnical Engineering (ABMS). This is in great part due to the geotechnical challenges involving swelling and collapsible soils commonly found in the country and issues related to landslide risk assessment and management. Progressively, problems associated with civil infrastructure, transportation geotechnics, environmental geotechnics, and engineered mine tailings disposal systems have also drawn the attention of professionals dealing with unsaturated soils. This paper celebrates the 75th anniversary of ABMS by presenting a summary of some of the main advances produced by Brazilian academia and geotechnical practitioners, in the field of USM and UST. Fundamentals of unsaturated soil are discussed, in the context of some typical Brazilian soils, including issues regarding soil microstructure, soil-water retention, and unsaturated shear strength. Brazilian developments in terms of swelling and collapsible soil identification, testing, and modeling are explored. Finally, geotechnical and geoenvironmental applications are discussed, focusing on the main issues investigated in the past four decades.
- 21 July 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (3)
Open AccessAdvances in unsaturated soils mechanics and technology in Brazil
Unsaturated soils mechanics (USM) and unsaturated soils technology (UST) have been the subject of great interest to Brazilian researchers and practitioners since the inception of the Brazilian Association for Soil Mechanics and Geotechnical Engineering (ABMS). This is in great part due to the geotechnical challenges involving swelling and collapsible soils commonly found in the country and issues related to landslide risk assessment and management. Progressively, problems associated with civil infrastructure, transportation geotechnics, environmental geotechnics, and engineered mine tailings disposal systems have also drawn the attention of professionals dealing with unsaturated soils. This paper celebrates the 75th anniversary of ABMS by presenting a summary of some of the main advances produced by Brazilian academia and geotechnical practitioners, in the field of USM and UST. Fundamentals of unsaturated soil are discussed, in the context of some typical Brazilian soils, including issues regarding soil microstructure, soil-water retention, and unsaturated shear strength. Brazilian developments in terms of swelling and collapsible soil identification, testing, and modeling are explored. Finally, geotechnical and geoenvironmental applications are discussed, focusing on the main issues investigated in the past four decades.
- Open Access
- 16 October 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (10) , 273
Conceptual and Applied Aspects of Water Retention Tests on Tailings Using Columns
The water retention capacity of porous materials is crucial in various geotechnical and environmental engineering applications such as slope stability analysis, landfill management, and mining operations. Filtered tailings stacks are considered an alternative to traditional tailings dams. Nevertheless, the mechanical behaviour and stability of the material under different water content conditions are of concern because these stacks can reach considerable heights. The water behaviour in these structures is poorly understood, particularly the effects of the water content on the stability and potential for liquefaction of the stacks. This study aims to investigate the water retention and flow characteristics of compacted iron ore tailings in high columns to better understand their hydromechanical behaviour. The research used 5 m high columns filled with iron ore tailings from the Quadrilátero Ferrífero region in Minas Gerais, Brazil. The columns were prepared in layers, compacted, and instrumented with moisture content sensors and suction sensors to monitor the water movement during various stages of saturation, drainage, infiltration, and evaporation. The sensors provided consistent data and revealed that the tailings exhibited high drainage capacity. The moisture content and suction profiles were effectively established over time and revealed the dynamic water retention behaviour. The comparison of the data with the theoretical soil water retention curve (SWRC) demonstrated a good correlation which indicates that there was no hysteresis in the material response. The study concludes that the column setup effectively captures the water retention and flow characteristics of compacted tailings and provides valuable insights for the hydromechanical analysis of filtered tailings stacks. These findings can significantly help improve numerical models, calibrate material parameters, and contribute to the safer and more efficient management of tailings storage facilities.
- 16 October 2024
- Published by MDPI AG in Geosciences
- Vol. 14 (10) , 273
Open AccessConceptual and Applied Aspects of Water Retention Tests on Tailings Using Columns
The water retention capacity of porous materials is crucial in various geotechnical and environmental engineering applications such as slope stability analysis, landfill management, and mining operations. Filtered tailings stacks are considered an alternative to traditional tailings dams. Nevertheless, the mechanical behaviour and stability of the material under different water content conditions are of concern because these stacks can reach considerable heights. The water behaviour in these structures is poorly understood, particularly the effects of the water content on the stability and potential for liquefaction of the stacks. This study aims to investigate the water retention and flow characteristics of compacted iron ore tailings in high columns to better understand their hydromechanical behaviour. The research used 5 m high columns filled with iron ore tailings from the Quadrilátero Ferrífero region in Minas Gerais, Brazil. The columns were prepared in layers, compacted, and instrumented with moisture content sensors and suction sensors to monitor the water movement during various stages of saturation, drainage, infiltration, and evaporation. The sensors provided consistent data and revealed that the tailings exhibited high drainage capacity. The moisture content and suction profiles were effectively established over time and revealed the dynamic water retention behaviour. The comparison of the data with the theoretical soil water retention curve (SWRC) demonstrated a good correlation which indicates that there was no hysteresis in the material response. The study concludes that the column setup effectively captures the water retention and flow characteristics of compacted tailings and provides valuable insights for the hydromechanical analysis of filtered tailings stacks. These findings can significantly help improve numerical models, calibrate material parameters, and contribute to the safer and more efficient management of tailings storage facilities.
- Open Access
- 26 July 2023
- Published by Coimbra University Press in Geotecnia
- No. 158,p. 49-64
Parâmetros intrínsecos da argila dura cinza esverdeada da Formação Resende
As argilas duras são materiais que possuem características muito particulares, que podem influenciar diretamente no desenvolvimento de projetos e segurança das obras. Na cidade de São Paulo, um dos principais solos de ocorrência são justamente argilas desse tipo, as chamadas argilas duras cinza-esverdeadas. A história geológica desse material pode induzir uma estrutura particular no solo e a influência dessa estrutura poderá ser compreendida a partir da comparação de seus parâmetros naturais com os parâmetros intrínsecos, que são aqueles obtidos em ensaios com amostras reconstituídas aqui apresentados. Atualmente, os poucos dados disponíveis sobre este solo na literatura são referentes apenas a ensaios realizados com amostras indeformadas, não havendo dados de amostras reconstituídas. Portanto, o objetivo deste trabalho é determinar os parâmetros intrínsecos desta argila, por meio de ensaios na condição reconstituída.
- 26 July 2023
- Published by Coimbra University Press in Geotecnia
- No. 158,p. 49-64
Open AccessParâmetros intrínsecos da argila dura cinza esverdeada da Formação Resende
As argilas duras são materiais que possuem características muito particulares, que podem influenciar diretamente no desenvolvimento de projetos e segurança das obras. Na cidade de São Paulo, um dos principais solos de ocorrência são justamente argilas desse tipo, as chamadas argilas duras cinza-esverdeadas. A história geológica desse material pode induzir uma estrutura particular no solo e a influência dessa estrutura poderá ser compreendida a partir da comparação de seus parâmetros naturais com os parâmetros intrínsecos, que são aqueles obtidos em ensaios com amostras reconstituídas aqui apresentados. Atualmente, os poucos dados disponíveis sobre este solo na literatura são referentes apenas a ensaios realizados com amostras indeformadas, não havendo dados de amostras reconstituídas. Portanto, o objetivo deste trabalho é determinar os parâmetros intrínsecos desta argila, por meio de ensaios na condição reconstituída.
- Open Access
- 24 April 2023
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 382, 16003
Evaluation a volumetric water content sensor to be used for compacted filtered iron ore tailings
The use of compacted landfills for filtered tailings has grown to replace dams. Considering that this is a structure that must remain in the unsaturated condition, it is necessary to monitor the flow pattern and water retention in these landfills. The use of sensors for the automatic monitoring of volumetric water content is a fundamental tool for use in the field. Sensors that use the technique called FDR (Frequency Domain Refractometry) emit an electromagnetic signal that, associated with the ability of materials to store electrical charge, allows the determination of the so-called dielectric constant. The dielectric constant relates the capacitance of the material to the capacitance of the air. As the dielectric constant in air is, by definition, equal to 1 and of the water, at 20 degrees Celsius, equal to 80, materials with a range proportion of air and water have variable dielectric constant values, considering the dielectric constant of minerals being constant. Many commercial sensors already come with a calibration curve that is based on typical soils (quartz and feldspar). However, in the case of iron mining tailings, in addition of having a very different mineral composition from the soils normally founded, there is the possibility that the presence of very fine particles could alter the dielectric constant of the liquid. In this way, it is essential to obtain a specific calibration curve, taking into account not only the material, but also the density of it. The sensor used in the present study is the TEROS 12. The results obtained for the sensor calibration in the case of iron ore tailings, demands a specific calibration to be performed for the material and each density to be used. The process used for the calibration and the equations obtained are presented in this paper.
- 24 April 2023
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 382, 16003
Open AccessEvaluation a volumetric water content sensor to be used for compacted filtered iron ore tailings
The use of compacted landfills for filtered tailings has grown to replace dams. Considering that this is a structure that must remain in the unsaturated condition, it is necessary to monitor the flow pattern and water retention in these landfills. The use of sensors for the automatic monitoring of volumetric water content is a fundamental tool for use in the field. Sensors that use the technique called FDR (Frequency Domain Refractometry) emit an electromagnetic signal that, associated with the ability of materials to store electrical charge, allows the determination of the so-called dielectric constant. The dielectric constant relates the capacitance of the material to the capacitance of the air. As the dielectric constant in air is, by definition, equal to 1 and of the water, at 20 degrees Celsius, equal to 80, materials with a range proportion of air and water have variable dielectric constant values, considering the dielectric constant of minerals being constant. Many commercial sensors already come with a calibration curve that is based on typical soils (quartz and feldspar). However, in the case of iron mining tailings, in addition of having a very different mineral composition from the soils normally founded, there is the possibility that the presence of very fine particles could alter the dielectric constant of the liquid. In this way, it is essential to obtain a specific calibration curve, taking into account not only the material, but also the density of it. The sensor used in the present study is the TEROS 12. The results obtained for the sensor calibration in the case of iron ore tailings, demands a specific calibration to be performed for the material and each density to be used. The process used for the calibration and the equations obtained are presented in this paper.
- 1 January 2023
- Published by Editora Cubo
- p. 325-352
Instrumentação de laboratório e campo e a medição da Curva de retenção
- 1 January 2023
- Published by Editora Cubo
- p. 325-352
Instrumentação de laboratório e campo e a medição da Curva de retenção
- 17 September 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (3) , 1-13
Brasília municipal solid waste landfill: a case study on flow and slope stability
For geotechnical and environmental reasons, landfills are positioned above the regional water table and thus are formed in unsaturated conditions. This condition can be different if the drainage system and the rain regime of the site are such that they create a level of internal liquid in the landfill. During January and February 2019, excessive movements occurred in the slopes of the Brasília sanitary landfill. A geotechnical investigation indicated that the raised leachate level caused by the clogging of the drainage system contributed to the landfilled waste movements. The limit equilibrium analysis was used to predict the relationship between leachate level and slope stability. In order to understand the process that led to the rupture, flow and stability analysis by limit equilibrium were performed. The parameters associated with flow, water retention capacity, and shear strength were obtained based on literature evaluations. In addition, data from tests were used, which allowed to define more accurately the distribution of pore pressures of liquid that led to the failure. This study allowed to define the cause of failure and also to establish the role of the drainage system in maintaining the stability of the landfill. The studies indicated that although the gain of shear strength of landfill due to the unsaturated condition is negligible, the process of flow in unsaturated medium, associated with climatic aspects, are fundamental for a medium- and long-term analysis.
- 17 September 2021
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 44 (3) , 1-13
Brasília municipal solid waste landfill: a case study on flow and slope stability
For geotechnical and environmental reasons, landfills are positioned above the regional water table and thus are formed in unsaturated conditions. This condition can be different if the drainage system and the rain regime of the site are such that they create a level of internal liquid in the landfill. During January and February 2019, excessive movements occurred in the slopes of the Brasília sanitary landfill. A geotechnical investigation indicated that the raised leachate level caused by the clogging of the drainage system contributed to the landfilled waste movements. The limit equilibrium analysis was used to predict the relationship between leachate level and slope stability. In order to understand the process that led to the rupture, flow and stability analysis by limit equilibrium were performed. The parameters associated with flow, water retention capacity, and shear strength were obtained based on literature evaluations. In addition, data from tests were used, which allowed to define more accurately the distribution of pore pressures of liquid that led to the failure. This study allowed to define the cause of failure and also to establish the role of the drainage system in maintaining the stability of the landfill. The studies indicated that although the gain of shear strength of landfill due to the unsaturated condition is negligible, the process of flow in unsaturated medium, associated with climatic aspects, are fundamental for a medium- and long-term analysis.
- 23 June 2020
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 38 (6) , 6145-6155
Effect of Suction on the Shear Strength of Soil–Rock Interfaces
- 23 June 2020
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 38 (6) , 6145-6155
Effect of Suction on the Shear Strength of Soil–Rock Interfaces