VSValdas Sirutkaitis

Valdas Sirutkaitis

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Valdas Sirutkaitis has a total of 48 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Scanning Algorithm Optimization for Achieving Low-Roughness Surfaces Using Ultrashort Laser Pulses: A Comparative Study

    by Evaldas Kažukauskas, Simas Butkus, Vytautas Jukna, Domas Paipulas, Valdas Sirutkaitis

    Femtosecond laser-assisted material surface modification is a rapidly growing field with numerous applications, including tribology, micromechanics, optofluidics, and medical implant treatment. For many of these applications, precise control of surface roughness after laser treatment is crucial, as it directly affects the final properties of the work surface. However, achieving low mean surface roughness values (<100 nm) is challenging due to the fundamental principles of laser light–matter interactions. The complex physical processes that occur during laser material interactions make it difficult to achieve the desired surface roughness, and only advanced scanning methods can potentially solve this issue. In our study, we analyzed laser scanning algorithms to determine the optimal method for producing surfaces with minimal roughness. We investigated how scanning parameters such as the overlap of modifications, the amount of successive line shift, and laser-scanner synchronization impact surface roughness. Using a numerical model, we obtained results that showed good agreement with experimentally acquired data. Our detailed theoretical and experimental analysis of different scanning methods can provide valuable information for the future optimization of minimal-roughness micromachining.


  • Open Access

    High-Contrast Marking of Stainless-Steel Using Bursts of Femtosecond Laser Pulses

    by Simas Butkus, Vytautas Jukna, Evaldas Kažukauskas, Žilvinas Svirksas, Domas Paipulas, Valdas Sirutkaitis

    The marking and surface structuring of various materials is important in various industrial fields such as biomaterials, luxury goods, anti-counterfeiting, automotive and aerospace, electronics and semiconductor industries, and others. Recent advances in laser technology, such as burst-mode lasers, have opened new ways of affecting the surfaces of various materials, inducing a different appearance and/or properties of the laser-exposed areas. From earlier studies, it is known that when splitting a single pulse into multiple pulses and thus creating a quasi-MHz–GHz repetition rate regime, it is possible to increase not only the ablation efficiency but it also provides the possibility to tune the heat in-flow into the surface. Such new regimes enable the control of the surface roughness as well as the optical properties and corrosion resistance. In this work, we analyze the effect of the different burst-mode regimes for the marking of stainless-steel samples, aiming to produce high-contrast marking having different shades of black/white color (black-gray-white). Moreover, we investigate the angular dependence of the reflected light after laser treatment numerically from the measured surface morphology


  • Open Access

    Sapphire Selective Laser Etching Dependence on Radiation Wavelength and Etchant

    by Agnė Butkutė, Romualdas Sirutkaitis, Darius Gailevičius, Domas Paipulas, Valdas Sirutkaitis

    Transparent and high-hardness materials have become the object of wide interest due to their optical and mechanical properties; most notably, concerning technical glasses and crystals. A notable example is sapphire—one of the most rigid materials having impressive mechanical stability, high melting point and a wide transparency window reaching into the UV range, together with impressive laser-induced damage thresholds. Nonetheless, using this material for 3D micro-fabrication is not straightforward due to its brittle nature. On the microscale, selective laser etching (SLE) technology is an appropriate approach for such media. Therefore, we present our research on C-cut crystalline sapphire microprocessing by using femtosecond radiation-induced SLE. Here, we demonstrate a comparison between different wavelength radiation (1030 nm, 515 nm, 343 nm) usage for material modification and various etchants (hydrofluoric acid, sodium hydroxide, potassium hydroxide and sulphuric and phosphoric acid mixture) comparison. Due to the inability to etch crystalline sapphire, regular SLE etchants, such as hydrofluoric acid or potassium hydroxide, have limited adoption in sapphire selective laser etching. Meanwhile, a 78% sulphuric and 22% phosphoric acid mixture at 270 °C temperature is a good alternative for this process. We present the changes in the material after the separate processing steps. After comparing different processing protocols, the perspective is demonstrated for sapphire structure formation.


  • Open Access

    Sapphire Selective Laser Etching Dependence on Radiation Wavelength and Etchant

    by Agne Butkute, Romualdas Sirutkaitis, Darius Gailevičius, Domas Paipulas, Valdas Sirutkaitis

    Transparent and high-hardness materials have become the object of wide interest. Most notably, it concerns technical glasses and crystals. A notable example is a sapphire – one of the most rigid materials having impressive mechanical stability and good optical properties. Nonetheless, using this material for 3D micro-fabrication is not straightforward due to its brittle nature. On the microscale, selective laser etching (SLE) technology is an appropriate approach for such media. Therefore, we present our research on c-cut crystalline sapphire microprocessing by using femtosecond radiation-induced SLE. Here we demonstrate a comparison between different wavelength radiation (1030 nm, 515 nm, 343 nm) usage for modification inscription and various etchants (Hydrofloridic acid, Sodium Hydroxide, Potassium Hydroxide and Sulphuric and Phosphoric acid mixture) comparison. We show that regular SLE etchants such as Hydrofluoric acid or Potassium Hydroxide are unsuitable materials for selective sapphire laser etching. Meanwhile, a 78% sulphuric and 22% phosphoric acid mixture at 270°C temperature is a good alternative for this process. We present the changes in the material after the separate processing steps. Finally, a protocol for advanced sapphire structure formation and a few exemplary structures are presented.


  • Open Access

    Femtosecond Laser Assisted 3D Etching Using Inorganic-Organic Etchant

    by Agnė Butkutė, Greta Merkininkaitė, Tomas Jurkšas, Jokūbas Stančikas, Tomas Baravykas, Rokas Vargalis, Titas Tičkūnas, Julien Bachmann, Simas Šakirzanovas, Valdas Sirutkaitis, et al.

    Selective laser etching (SLE) is a technique that allows the fabrication of arbitrarily shaped glass micro-objects. In this work, we show how the capabilities of this technology can be improved in terms of selectivity and etch rate by applying an etchant solution based on a Potassium Hydroxide, water, and isopropanol mixture. By varying the concentrations of these constituents, the wetting properties, as well as the chemical reaction of fused silica etching, can be changed, allowing us to achieve etching rates in modified fused silica up to 820 μm/h and selectivity up to ∼3000. This is used to produce a high aspect ratio (up to 1:1000), straight and spiral microfluidic channels which are embedded inside a volume of glass. Complex 3D glass micro-structures are also demonstrated.


  • Femtosecond UV laser lift-off technique for GaN coatings

    by Domas Paipulas, Simas Butkus, Valdas Sirutkaitis

    Thin coatings of functionalized gallium nitride (GaN) have become a staple technology for blue photonics and various optoelectronic devices. Traditionally these coatings are epitaxially grown on hard substrates such as sapphire and SiC, and for many applications, coating delamination is required. One of the most promising coating separation techniques is the non-contact Laser Lift-Off (LLO) method pioneered by W.Wong and M.Kelly [1] , [2] . LLO technique relies on different bandgaps between the substrate and GaN, which allows direct UV light absorption at the intersection, leading to thermal decomposition of the bonding layer and subsequent coating separation. To this day, nanosecond UV lasers (mainly excimer systems) are considered as the primary choices for industrial lift-off applications; on the other hand, recent advancements in industrial femtosecond laser sources start to shift this trend. In the past few years, several successful demonstrations of femtosecond GaN LLO process was reported in the literature: a thin slicing of GaN layer from the bulk substrate was performed by localized material decomposition driven from nonlinear absorption of IR radiation [3] ; also a complete separation of GaN from sapphire was demonstrated with visible radiation [4] . Despite the mediocre surface quality, occasional appearance of,,hot spots", caused by higher absorption centers and stitching irregularities, these works prove that even working in a nonlinear absorption regime, a successfully GaN separation can be achieved.


  • Open Access

    Micromachining of Transparent Biocompatible Polymers Applied in Medicine Using Bursts of Femtosecond Laser Pulses

    by Evaldas Kažukauskas, Simas Butkus, Piotr Tokarski, Vytautas Jukna, Martynas Barkauskas, Valdas Sirutkaitis

    Biocompatible polymers are used for many different purposes (catheters, artificial heart components, dentistry products, etc.). An important field for biocompatible polymers is the production of vision implants known as intraocular lenses or custom-shape contact lenses. Typically, curved surfaces are manufactured by mechanical means such as milling, turning or lathe cutting. The 2.5 D objects/surfaces can also be manufactured by means of laser micromachining; however, due to the nature of light–matter interaction, it is difficult to produce a surface finish with surface roughness values lower than ~1 µm Ra. Therefore, laser micromachining alone can’t produce the final parts with optical-grade quality. Laser machined surfaces may be polished via mechanical methods; however, the process may take up to several days, which makes the production of implants economically challenging. The aim of this study is the investigation of the polishing capabilities of rough (~1 µm Ra) hydrophilic acrylic surfaces using bursts of femtosecond laser pulses. By changing different laser parameters, it was possible to find a regime where the surface roughness can be minimized to 18 nm Ra, while the polishing of the entire part takes a matter of seconds. The produced surface demonstrates a transparent appearance and the process shows great promise towards commercial fabrication of low surface roughness custom-shape optics.


  • Open Access

    Micromachining of Invar Foils with GHz, MHz and kHz Femtosecond Burst Modes

    by Simas Butkus, Vytautas Jukna, Domas Paipulas, Martynas Barkauskas, Valdas Sirutkaitis

    In this work, a burst mode laser is used for micromachining of 20 µm–250 µm thick Invar (Fe64/Ni36) foils. Holes were drilled by firing multiple pulses transversely onto the sample without moving the beam (percussion drilling). The utilized laser system generates a burst of a controllable number of pulses (at 1030 nm) with tunable pulse-to-pulse time spacing ranging from 200 ps to 16 ns. The sub-pulses within the burst have equal amplitudes and a constant duration of 300 fs that do not change regardless of the spacing in time between them. In such a way, the laser generates GHz to MHz repetition rate pulse bursts with a burst repetition rate ranging from 100 kHz to a single shot. Drilling of the material is compared with the non-burst mode of kHz repetition rate. In addition, we analyze the drilling speed and the resulting dependence of the quality of the holes on the number of pulses per burst as well as the average laser power to find the optimal micromachining parameters for percussion drilling. We demonstrate that the micromachining throughput can be of an order of magnitude higher when using the burst mode as compared to the best results of the conventional kHz case; however, excess thermal damage was also evident in some cases.


  • Open Access

    Femtosecond Beam Transformation Effects in Water, Enabling Increased Throughput Micromachining in Transparent Materials

    by Simas Butkus, Eugenijus Gaižauskas, Lina Mačernytė, Vytautas Jukna, Domas Paipulas, Valdas Sirutkaitis

    Femtosecond lasers are widely applied in scientific and industrial fields. Recent trends in the laser market show decreasing prices for femtosecond units, which will ultimately lead to the opening of new markets that were inaccessible in the past due to the high costs of such systems. To this end, new techniques that enable micromachining of materials with increased efficiency are interesting. In this article, we demonstrate a technique that may be used for cutting and drilling various materials. By placing a layer of water on top of the samples and loosely focusing laser light on the surface, it was found that the micromachining throughput is increased by up to 10-fold as compared with micromachining without the water layer (conventional focusing in air), however, the main reasons for the increase in fabrication efficiency have not been fully understood until now. By modelling the propagation of the femtosecond pulses by means of the nonlinear modified Schrodinger equation through the water layer, we show that the increased throughput is attributed to the changing of the Gaussian intensity profile. In addition, we confirm these findings by numerically modelling the ablated crater formation.


  • Open Access

    Analysis of the Micromachining Process of Dielectric and Metallic Substrates Immersed in Water with Femtosecond Pulses

    by Simas Butkus, Aleksandr Alesenkov, Domas Paipulas, Eugenijus Gaižauskas, Andrius Melninkaitis, Dalia Kaškelytė, Martynas Barkauskas, Valdas Sirutkaitis

    Micromachining of 1 mm thick dielectric and metallic substrates was conducted using femtosecond pulse generated filaments in water. Several hundred microjoule energy pulses were focused within a water layer covering the samples. Within this water layer, non-linear self-action mechanisms transform the beam, which enables higher quality and throughput micromachining results compared to focusing in air. Evidence of beam transformation into multiple light filaments is presented along with theoretical modeling results. In addition, multiparametric optimization of the fabrication process was performed using statistical methods and certain acquired dependencies are further explained and tested using laser shadowgraphy. We demonstrate that this micromachining process exhibits complicated dynamics within the water layer, which are influenced by the chosen parameters.