Santosh Gopalakrishnan Thampi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Santosh Gopalakrishnan Thampi has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Subhashini Kumudesan Pramada
Department of Civil Engineering, National Institute of Technology Calicut, Kozhikode, India
4 shared publications - Aditya Harikumar
Department of Civil Engineering, NIT Calicut, Calicut, India
3 shared publications - Chithra Nelson Rosamma
Department of Civil Engineering, National Institute of Technology Calicut, Kozhikode, India
3 shared publications - Jisha John
NIT Calicut
3 shared publications - N. M. Sabitha
KSCSTE-NATPAC
3 shared publications - S. Sithara
Department of Civil, Architectural, and Environmental Engineering, University of Padova, Padova, Postal code: 35131 Italy
3 shared publications
Latest Publications
- Open Access
Effect of Thermal Loads on the Structural Response of an Aging Double-Curvature Thin Concrete Arch Dam Experiencing Significant Reservoir Level Fluctuations
High arch dams are structurally efficient hydraulic structures for demanding loading conditions, including extreme loading, and are widely recognized for the transfer mechanism of such loads acting on them. The distinctive performance of these thin concrete structures during their service life is often intriguing and worth investigating. Unlike in the case of concrete gravity dams, in arch dams—especially, thin arch dams—the impact of temperature loads assumes significance due to the geometry and load-transfer mechanism. In this paper, an existing high double-curvature thin concrete arch dam experiencing fluctuations in reservoir levels is analyzed regarding the combined effect of thermal loads and the deflections and stresses caused. Thermal loads arising from continuous exposure of intrados and extrados faces contribute to critical loading scenarios. The FEM-based simulations assisted with field monitoring data and were used to study the structural response under the influence of temperature in steady-state conditions. The study found that the increase in body temperature is a cause of undesirable tensile stresses in the upper parts of the dam body, close to 2.0 MPa, which may cause the development of horizontal cracks. Small areas of upstream heel portion also develop higher tensile stresses due to temperature loads. The dam in its 50-year service life showed apparently aberrant behavior in deflections. The seasonal temperature variation—an increase—can be a cause of the atypical response of the dam. The anomalous nature of the behavior cannot be considered unusual, but the study also found that mitigation measures are effective, suggesting that continuous monitoring is required for sustained healthy functioning.
Open AccessEffect of Thermal Loads on the Structural Response of an Aging Double-Curvature Thin Concrete Arch Dam Experiencing Significant Reservoir Level Fluctuations
High arch dams are structurally efficient hydraulic structures for demanding loading conditions, including extreme loading, and are widely recognized for the transfer mechanism of such loads acting on them. The distinctive performance of these thin concrete structures during their service life is often intriguing and worth investigating. Unlike in the case of concrete gravity dams, in arch dams—especially, thin arch dams—the impact of temperature loads assumes significance due to the geometry and load-transfer mechanism. In this paper, an existing high double-curvature thin concrete arch dam experiencing fluctuations in reservoir levels is analyzed regarding the combined effect of thermal loads and the deflections and stresses caused. Thermal loads arising from continuous exposure of intrados and extrados faces contribute to critical loading scenarios. The FEM-based simulations assisted with field monitoring data and were used to study the structural response under the influence of temperature in steady-state conditions. The study found that the increase in body temperature is a cause of undesirable tensile stresses in the upper parts of the dam body, close to 2.0 MPa, which may cause the development of horizontal cracks. Small areas of upstream heel portion also develop higher tensile stresses due to temperature loads. The dam in its 50-year service life showed apparently aberrant behavior in deflections. The seasonal temperature variation—an increase—can be a cause of the atypical response of the dam. The anomalous nature of the behavior cannot be considered unusual, but the study also found that mitigation measures are effective, suggesting that continuous monitoring is required for sustained healthy functioning.
- 3 August 2026
- Published by Wiley in Environmental Progress & Sustainable Energy
- p. e70617
Rheology‐driven material design of sustainable cementitious composites for extrusion‐based additive manufacturing via particle packing optimization
The development of extrusion‐based cementitious materials for additive manufacturing requires precise control of rheological behavior and particle‐scale interactions governing flow and structural build‐up. This study investigates the role of particle packing and supplementary cementitious material (SCM) distribution on the rheological and mechanical response of sustainable cementitious composites incorporating recycled fine aggregate (RFA). A particle packing approach based on the Elkem Material Mixture Analyzer (EMMA) was employed to design a dense granular skeleton, enabling systematic variation of binder composition within a constrained packing domain. The effects of SCMs (fly ash, silica fume, and ground granulated blast‐furnace slag) and RFA content on flowability, yield stress evolution, and thixotropic behavior were evaluated through rheological characterization and extrusion‐based printability assessment. Results indicate that optimized particle packing significantly enhances shear‐thinning behavior and promotes rapid structural build‐up after deposition, enabling stable filament formation and multi‐layer stacking. The incorporation of SCMs modifies interparticle interactions and paste rheology, contributing to improved cohesion and reduced segregation tendency. The optimized composite exhibited a balanced response, achieving controlled flow (165 mm slump), stable extrusion, and sustained layer deposition, while maintaining a compressive strength of 39.8 MPa and flexural strength of 5.72 MPa at 28 days. The findings demonstrate that particle‐scale material design governs the coupling between rheological response and structural performance in extrusion‐based cementitious systems. This study provides insight into the fundamental role of packing density and binder composition in tailoring sustainable materials for additive manufacturing applications.
- 3 August 2026
- Published by Wiley in Environmental Progress & Sustainable Energy
- p. e70617
Rheology‐driven material design of sustainable cementitious composites for extrusion‐based additive manufacturing via particle packing optimization
The development of extrusion‐based cementitious materials for additive manufacturing requires precise control of rheological behavior and particle‐scale interactions governing flow and structural build‐up. This study investigates the role of particle packing and supplementary cementitious material (SCM) distribution on the rheological and mechanical response of sustainable cementitious composites incorporating recycled fine aggregate (RFA). A particle packing approach based on the Elkem Material Mixture Analyzer (EMMA) was employed to design a dense granular skeleton, enabling systematic variation of binder composition within a constrained packing domain. The effects of SCMs (fly ash, silica fume, and ground granulated blast‐furnace slag) and RFA content on flowability, yield stress evolution, and thixotropic behavior were evaluated through rheological characterization and extrusion‐based printability assessment. Results indicate that optimized particle packing significantly enhances shear‐thinning behavior and promotes rapid structural build‐up after deposition, enabling stable filament formation and multi‐layer stacking. The incorporation of SCMs modifies interparticle interactions and paste rheology, contributing to improved cohesion and reduced segregation tendency. The optimized composite exhibited a balanced response, achieving controlled flow (165 mm slump), stable extrusion, and sustained layer deposition, while maintaining a compressive strength of 39.8 MPa and flexural strength of 5.72 MPa at 28 days. The findings demonstrate that particle‐scale material design governs the coupling between rheological response and structural performance in extrusion‐based cementitious systems. This study provides insight into the fundamental role of packing density and binder composition in tailoring sustainable materials for additive manufacturing applications.
- 18 July 2026
- Published by Springer Nature in Water Resources Management
- Vol. 40 (10) , 476
A Fuzzy Analytic Hierarchy Process Framework for Estimating Potential Loss of Life in Dam-Failure Scenarios
- 18 July 2026
- Published by Springer Nature in Water Resources Management
- Vol. 40 (10) , 476
A Fuzzy Analytic Hierarchy Process Framework for Estimating Potential Loss of Life in Dam-Failure Scenarios
- 8 July 2026
- Published by Taylor & Francis in Hydrological Sciences Journal
- Vol. 71 (13) , 1-23
A novel spatiotemporal melt factor framework for quantifying snow and glacier melt in alpine basins
- 8 July 2026
- Published by Taylor & Francis in Hydrological Sciences Journal
- Vol. 71 (13) , 1-23
A novel spatiotemporal melt factor framework for quantifying snow and glacier melt in alpine basins
- Open Access
- 6 March 2026
- Published by MDPI AG in Infrastructures
- Vol. 11 (3) , 86
Study of Structural Response and Safety of an Existing Double-Curvature Concrete Thin Arch Dam Under Extreme Temperature Loads
Concrete arch dams, which account for about 4% of large dams worldwide, are distinguished by their efficient geometry, economy, effective load distribution, and high storage capacity. Under thermal loads, they are susceptible to unusual behavior in terms of deflection and stresses due to geometrical peculiarities, construction methodology, and restraints, which in turn may cause potential failure. This paper analyzes the behavior of a 50-year-old double-curvature, high, thin concrete arch dam under extreme thermal loading and fluctuating water levels, using 3D linear elastic FEM analyses and monitoring data. It rigorously evaluates structural response—deflections and stresses—at salient locations and interaction zones under large temperature fluctuations, a key yet underexplored risk for thin concrete arch dams in tropical and equatorial regions. Using real monitoring data, the research also examines the effectiveness of rehabilitation measures designed to mitigate thermal impacts. Results indicate that the dam deflection reverses at extreme temperature drops and rises when the reservoir is at higher or lower levels, respectively, which is not unusual for thin concrete double-curvature arch dams. Long-term exposure to high extreme temperatures with low reservoir water levels may become a concern, as it can cause higher tensile stresses at salient points and significant dam deflections towards upstream.
- 6 March 2026
- Published by MDPI AG in Infrastructures
- Vol. 11 (3) , 86
Open AccessStudy of Structural Response and Safety of an Existing Double-Curvature Concrete Thin Arch Dam Under Extreme Temperature Loads
Concrete arch dams, which account for about 4% of large dams worldwide, are distinguished by their efficient geometry, economy, effective load distribution, and high storage capacity. Under thermal loads, they are susceptible to unusual behavior in terms of deflection and stresses due to geometrical peculiarities, construction methodology, and restraints, which in turn may cause potential failure. This paper analyzes the behavior of a 50-year-old double-curvature, high, thin concrete arch dam under extreme thermal loading and fluctuating water levels, using 3D linear elastic FEM analyses and monitoring data. It rigorously evaluates structural response—deflections and stresses—at salient locations and interaction zones under large temperature fluctuations, a key yet underexplored risk for thin concrete arch dams in tropical and equatorial regions. Using real monitoring data, the research also examines the effectiveness of rehabilitation measures designed to mitigate thermal impacts. Results indicate that the dam deflection reverses at extreme temperature drops and rises when the reservoir is at higher or lower levels, respectively, which is not unusual for thin concrete double-curvature arch dams. Long-term exposure to high extreme temperatures with low reservoir water levels may become a concern, as it can cause higher tensile stresses at salient points and significant dam deflections towards upstream.
- 19 January 2026
- Published by Springer Nature in Water Resources Management
- Vol. 40 (2) , 77
Assessment of Socio-Economic Damages Consequent To Dam Break Using A Data-Driven Approach
- 19 January 2026
- Published by Springer Nature in Water Resources Management
- Vol. 40 (2) , 77
Assessment of Socio-Economic Damages Consequent To Dam Break Using A Data-Driven Approach
- 26 November 2024
- Published by Wiley in Land Degradation & Development
- Vol. 36 (3) , 853-871
Estimation of Potential Impact of Land Use Change on Sediment Yield From a Small Tropical Watershed Using the TREX Erosion Model
Analysis of the influence of changes in land use on the sediment yield from watersheds provides crucial inputs that aid the development of appropriate strategies for the sustainable management of consequent land degradation. Event‐based hydrologic models can be used for performing such analysis, as long‐term hydrological datasets are not available for most of the rivers in developing countries like India. In this study, an event‐based Two‐Dimensional Runoff, Erosion, and Export (TREX) model was used to simulate the soil erosion process in Moozhy, an ungauged watershed in the Karamana River basin in Thiruvananthapuram District, Kerala State, India. Rainfall, streamflow, and sediment concentration data corresponding to three isolated storm events were used to calibrate and validate the model. The performance of the model was assessed using four statistical measures, namely, Percent bias (PBIAS), Nash‐Sutcliffe Efficiency Coefficient (NSEC), Coefficient of determination (R 2) and RMSE‐observations standard deviation ratio (RSR). The values of PBIAS varied between 46% and 49%, indicating satisfactory performance of the model. Also, from the values of NSEC and RSR, it can be concluded that the TREX model yields acceptable results. For a rainfall event that occurred on the 17 September 2017, the simulated values showed that about 1054 t of suspended sediments are transported from the watershed to the stream channels, and about 1020 t is carried out of the Moozhy watershed. Only a very small amount of sediment is left in the channel at the end of the simulation. About 34 t of sediment is deposited in the channel bed, about 0.04 t remains in suspension, and the balance 0.04 t remains in suspension as a suspended load. About 3% of the total sediment entering the reach of the stream considered in this study is deposited on the riverbed. The major component of the settled sediments is silt; about 12% of the total silt size fraction entering the stream settles on the river bed. Future scenarios of land use in the watershed were modelled using a hybrid Artificial Neural Network (ANN) and Cellular Automata (CA) model. These were used for simulating sediment discharge using the TREX erosion model. The predicted land use scenarios were used to investigate both short‐term (2025 and 2029) and long‐term (2037, 2045, and 2053) variations in sediment discharge. The sediment yield for the storm event that occurred on 17 September 2017 was used to benchmark the variation in sediment yield under the predicted land use scenarios. Results indicate that the peak runoff and the runoff volume are expected to increase by about 29% and 22% respectively in the period from 2005 to 2053. The expected increase in the volume of sediments in this period is about 50%; the peak sediment concentration is likely to increase by about 56%. The study highlights the threats of likely increase in soil erosion and consequent land degradation posed by unscientific changes in land use caused by urbanisation and calls for proper management interventions to address the problem.
- 26 November 2024
- Published by Wiley in Land Degradation & Development
- Vol. 36 (3) , 853-871
Estimation of Potential Impact of Land Use Change on Sediment Yield From a Small Tropical Watershed Using the TREX Erosion Model
Analysis of the influence of changes in land use on the sediment yield from watersheds provides crucial inputs that aid the development of appropriate strategies for the sustainable management of consequent land degradation. Event‐based hydrologic models can be used for performing such analysis, as long‐term hydrological datasets are not available for most of the rivers in developing countries like India. In this study, an event‐based Two‐Dimensional Runoff, Erosion, and Export (TREX) model was used to simulate the soil erosion process in Moozhy, an ungauged watershed in the Karamana River basin in Thiruvananthapuram District, Kerala State, India. Rainfall, streamflow, and sediment concentration data corresponding to three isolated storm events were used to calibrate and validate the model. The performance of the model was assessed using four statistical measures, namely, Percent bias (PBIAS), Nash‐Sutcliffe Efficiency Coefficient (NSEC), Coefficient of determination (R 2) and RMSE‐observations standard deviation ratio (RSR). The values of PBIAS varied between 46% and 49%, indicating satisfactory performance of the model. Also, from the values of NSEC and RSR, it can be concluded that the TREX model yields acceptable results. For a rainfall event that occurred on the 17 September 2017, the simulated values showed that about 1054 t of suspended sediments are transported from the watershed to the stream channels, and about 1020 t is carried out of the Moozhy watershed. Only a very small amount of sediment is left in the channel at the end of the simulation. About 34 t of sediment is deposited in the channel bed, about 0.04 t remains in suspension, and the balance 0.04 t remains in suspension as a suspended load. About 3% of the total sediment entering the reach of the stream considered in this study is deposited on the riverbed. The major component of the settled sediments is silt; about 12% of the total silt size fraction entering the stream settles on the river bed. Future scenarios of land use in the watershed were modelled using a hybrid Artificial Neural Network (ANN) and Cellular Automata (CA) model. These were used for simulating sediment discharge using the TREX erosion model. The predicted land use scenarios were used to investigate both short‐term (2025 and 2029) and long‐term (2037, 2045, and 2053) variations in sediment discharge. The sediment yield for the storm event that occurred on 17 September 2017 was used to benchmark the variation in sediment yield under the predicted land use scenarios. Results indicate that the peak runoff and the runoff volume are expected to increase by about 29% and 22% respectively in the period from 2005 to 2053. The expected increase in the volume of sediments in this period is about 50%; the peak sediment concentration is likely to increase by about 56%. The study highlights the threats of likely increase in soil erosion and consequent land degradation posed by unscientific changes in land use caused by urbanisation and calls for proper management interventions to address the problem.
- 21 February 2024
- Published by Springer Nature in Stochastic Environmental Research and Risk Assessment
- Vol. 38 (5) , 2065-2079
Quantifying uncertainty in future sea level projections downscaled from CMIP5 global climate models
- 21 February 2024
- Published by Springer Nature in Stochastic Environmental Research and Risk Assessment
- Vol. 38 (5) , 2065-2079
Quantifying uncertainty in future sea level projections downscaled from CMIP5 global climate models
- 9 November 2023
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 16 (12) , 1-15
Comparative analysis of two geologically similar and meteorologically distinct river basins of the Peninsular India
- 9 November 2023
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 16 (12) , 1-15
Comparative analysis of two geologically similar and meteorologically distinct river basins of the Peninsular India