Jae-Eung Oh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jae-Eung Oh has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
Jae-Eun Jeong
Graduate School of Mechanical Engineering, Hanyang University, Seoul, 133-791, Korea
11 shared publicationsIn-Hyung Yang
Graduate School of Mechanical Engineering, Hanyang University, Seoul, 133-791, Korea
9 shared publicationsJin-Su Kim
Hanyang University
7 shared publicationsHyoun-Jin Sim
Hanyang University
6 shared publicationsUn-Chang Jeong
Hanyang University
6 shared publicationsJi-Hyun Yoon
Graduate School of Mechanical Engineering, Hanyang University, Seoul, 133-791, Korea
5 shared publications
Latest Publications
- 1 September 2016
- Published by Institute of Noise Control Engineering (INCE) in Noise Control Engineering Journal
- Vol. 64 (5) , 634-645
Analysis of structure-borne noise in vehicles by modifying the stiffness of joint parts in the suspension system and vehicle body
This study aims to change and improve the transmitted force to the vehicle body, the noise transfer function (NTF), and vehicle interior noise by modifying the stiffness of joint parts, which are the local areas of the subframe and body in white (BIW) connected to isolators. We adopted frequency response function (FRF)-based substructuring in order to understand the effects of the stiffness of joint parts for reducing the vibration in the transfer path of a “chassis-isolator vehicle body”. In addition, a process that could be used to predict the vehicle interior noise was developed based on FRF-based substructuring. Using the FRF-based substructuring technique, the transmitted force from the chassis to the vehicle body caused by the increased stiffness of the joint parts in the chassis and vehicle body was calculated. Subsequently, the NTF from the joint parts of a vehicle body to the driver's ear location was calculated. In the chassis, the transmitted force to the vehicle body increased or decreased with increasing stiffness of the joint parts of the chassis, and the vehicle interior noise showed similar tendency of the transmitted force. In the vehicle body, the transmitted force to the vehicle body increased when the stiffness of the joint parts of the BIW was increased. However, as the noise transfer function was reduced beyond the increase in the transmitted force, the vehicle interior noise decreased. The role of the isolator stiffness is dominant for determining change of the transmitted force, which affects the vehicle interior noise. Therefore, in order to reduce the vehicle interior noise, the stiffness of isolator and joint parts should be set in consideration of the transmitted force from the chassis to the vehicle body.
- 1 September 2016
- Published by Institute of Noise Control Engineering (INCE) in Noise Control Engineering Journal
- Vol. 64 (5) , 634-645
Analysis of structure-borne noise in vehicles by modifying the stiffness of joint parts in the suspension system and vehicle body
This study aims to change and improve the transmitted force to the vehicle body, the noise transfer function (NTF), and vehicle interior noise by modifying the stiffness of joint parts, which are the local areas of the subframe and body in white (BIW) connected to isolators. We adopted frequency response function (FRF)-based substructuring in order to understand the effects of the stiffness of joint parts for reducing the vibration in the transfer path of a “chassis-isolator vehicle body”. In addition, a process that could be used to predict the vehicle interior noise was developed based on FRF-based substructuring. Using the FRF-based substructuring technique, the transmitted force from the chassis to the vehicle body caused by the increased stiffness of the joint parts in the chassis and vehicle body was calculated. Subsequently, the NTF from the joint parts of a vehicle body to the driver's ear location was calculated. In the chassis, the transmitted force to the vehicle body increased or decreased with increasing stiffness of the joint parts of the chassis, and the vehicle interior noise showed similar tendency of the transmitted force. In the vehicle body, the transmitted force to the vehicle body increased when the stiffness of the joint parts of the BIW was increased. However, as the noise transfer function was reduced beyond the increase in the transmitted force, the vehicle interior noise decreased. The role of the isolator stiffness is dominant for determining change of the transmitted force, which affects the vehicle interior noise. Therefore, in order to reduce the vehicle interior noise, the stiffness of isolator and joint parts should be set in consideration of the transmitted force from the chassis to the vehicle body.
- 24 February 2016
- Published by Korean Physical Society in Journal of the Korean Physical Society
- Vol. 68 (3) , 431-442
Optimization and performance improvement of an electromagnetic-type energy harvester with consideration of human walking vibration
- 24 February 2016
- Published by Korean Physical Society in Journal of the Korean Physical Society
- Vol. 68 (3) , 431-442
Optimization and performance improvement of an electromagnetic-type energy harvester with consideration of human walking vibration
- 31 August 2015
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 230 (7) , 928-941
Noise reduction of the automobile multi-mode muffler using differential gap control and neural network control
In this study, a controllable multi-mode exhaust system was investigated by analysing the acoustic structure of a low-noise low-back-pressure air exhaust system and forming its controller. After selecting the exhaust system structure that considered the frequency characteristics of the vehicle’s exhaust noise with a large acoustic transmission loss, the basic muffler of the controllable multi-mode exhaust system was designed. The basic structure of the controllable multi-mode muffler with a curved side inlet and a curved side outlet was determined. The theoretical and experimental values of the acoustic transmission loss for straight pipes and for curved pipes were compared with no significant difference. To control the curved multi-mode exhaust system, a differential gap controller and a neural network controller were designed and simulated for control tests. The study findings reveal that the use of the proposed model for noise control achieves a noise reduction of 40–50% over systems with no noise control, proving that this exhaust system is effective in noise control. The feasibility of the noise-controllable multi-mode exhaust system was investigated using both a differential gap controller and a neural network controller.
- 31 August 2015
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 230 (7) , 928-941
Noise reduction of the automobile multi-mode muffler using differential gap control and neural network control
In this study, a controllable multi-mode exhaust system was investigated by analysing the acoustic structure of a low-noise low-back-pressure air exhaust system and forming its controller. After selecting the exhaust system structure that considered the frequency characteristics of the vehicle’s exhaust noise with a large acoustic transmission loss, the basic muffler of the controllable multi-mode exhaust system was designed. The basic structure of the controllable multi-mode muffler with a curved side inlet and a curved side outlet was determined. The theoretical and experimental values of the acoustic transmission loss for straight pipes and for curved pipes were compared with no significant difference. To control the curved multi-mode exhaust system, a differential gap controller and a neural network controller were designed and simulated for control tests. The study findings reveal that the use of the proposed model for noise control achieves a noise reduction of 40–50% over systems with no noise control, proving that this exhaust system is effective in noise control. The feasibility of the noise-controllable multi-mode exhaust system was investigated using both a differential gap controller and a neural network controller.
- 3 June 2015
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 230 (3) , 371-381
Evaluation of the rattle noise of a vehicle seat using the coherence analysis technique
The complicated transfer path relationship between the vibrations of a seat and the noise at the locations of the driver’s ears was estimated from the residual spectrum. For accurate quantitative estimation of the rattle noise at the locations of the driver’s ears, in particular the partial coherence function of the pure inputs to the output was modelled by considering the correlation between the inputs and the input–output. Whenever a coherence analysis was performed with the noise sources in close proximity selected as the inputs and the noise at the locations of the driver’s ears modelled as the output, the partially coherent output spectrum as a quantitative contribution of the inputs to the output was determined. In this study, we applied a coherence analysis technique to identify the sources of the rattle noise of a seat by visualizing the noise sources with an acoustic camera while excitation of the seat was carried out using a hydraulic exciter. We were able to generate the rattle noise from the headrest stay, the recliner and the front part of the slide while excitation of the seat was obtained using a hydraulic exciter with white noise. We observed that the noise was generated by utilizing a hydraulic six-axis exciter positioned at the driver’s seat of a middle-sized manual transmission vehicle. We determined that the noise measured at the locations of the driver’s ears had a frequency of 58 Hz using acoustic visualization and a coherence technique. It was selected in particular as the target frequency since the 58 Hz resonant frequency caused by the twisting mode of the seat back was identical with the frequency of the rattle noise. Finally, it was verified through a modal test that the rattle noise at 58 Hz was generated by the vibration characteristics of the seat, which depended on gaps between the headrest stay and the guide.
- 3 June 2015
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 230 (3) , 371-381
Evaluation of the rattle noise of a vehicle seat using the coherence analysis technique
The complicated transfer path relationship between the vibrations of a seat and the noise at the locations of the driver’s ears was estimated from the residual spectrum. For accurate quantitative estimation of the rattle noise at the locations of the driver’s ears, in particular the partial coherence function of the pure inputs to the output was modelled by considering the correlation between the inputs and the input–output. Whenever a coherence analysis was performed with the noise sources in close proximity selected as the inputs and the noise at the locations of the driver’s ears modelled as the output, the partially coherent output spectrum as a quantitative contribution of the inputs to the output was determined. In this study, we applied a coherence analysis technique to identify the sources of the rattle noise of a seat by visualizing the noise sources with an acoustic camera while excitation of the seat was carried out using a hydraulic exciter. We were able to generate the rattle noise from the headrest stay, the recliner and the front part of the slide while excitation of the seat was obtained using a hydraulic exciter with white noise. We observed that the noise was generated by utilizing a hydraulic six-axis exciter positioned at the driver’s seat of a middle-sized manual transmission vehicle. We determined that the noise measured at the locations of the driver’s ears had a frequency of 58 Hz using acoustic visualization and a coherence technique. It was selected in particular as the target frequency since the 58 Hz resonant frequency caused by the twisting mode of the seat back was identical with the frequency of the rattle noise. Finally, it was verified through a modal test that the rattle noise at 58 Hz was generated by the vibration characteristics of the seat, which depended on gaps between the headrest stay and the guide.
- 12 January 2015
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 229 (11) , 1443-1456
Reduction in the moan noise by frequency-response-function-based substructuring and optimization techniques
‘Moan’ noise in a vehicle causes discomfort and anxiety to passengers. In the previous study, the causes of moan noise were identified, and a coherence analysis of the components was conducted. It was found that moan noise was generated by the attribution of resonance when the exciting force produced by the stick–slip motion in a brake system was transmitted to a coupled torsional beam axle module. The analysis involved calculation of the response of the coupled torsional beam axle module on a full suspension brake system reconstructed by consideration of the transfer functions and the joint conditions of the coupled torsional beam axle module and the brake system. Each transfer function is decomposed by a frequency-response-function-based substructuring technique. In this study, when using the sensitivity analysis and optimization techniques for moan-noise reduction, the frequency-response-function-based substructuring technique was performed to calculate the response of the modified coupled torsional beam axle module by considering the joint conditions and the transfer functions of the brake system. Highly sensitive design parameters regarding the response of the coupled torsional beam axle module were identified after the sensitivity analysis. The most sensitive design parameters were selected to enhance the efficiency and the robustness of optimization. The optimal values for the design variables were obtained by applying a progressive quadratic response surface method as a optimization algorithm. The application of an optimization technique was possible using the finite element model and the results of the finite element analysis from the previous study. After optimization, a prototype was re-designed, manufactured and tested. Finally, it was verified that the moan noise was reduced, as the natural frequency of 387 Hz for the coupled torsional beam axle module was moved to a higher frequency.
- 12 January 2015
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 229 (11) , 1443-1456
Reduction in the moan noise by frequency-response-function-based substructuring and optimization techniques
‘Moan’ noise in a vehicle causes discomfort and anxiety to passengers. In the previous study, the causes of moan noise were identified, and a coherence analysis of the components was conducted. It was found that moan noise was generated by the attribution of resonance when the exciting force produced by the stick–slip motion in a brake system was transmitted to a coupled torsional beam axle module. The analysis involved calculation of the response of the coupled torsional beam axle module on a full suspension brake system reconstructed by consideration of the transfer functions and the joint conditions of the coupled torsional beam axle module and the brake system. Each transfer function is decomposed by a frequency-response-function-based substructuring technique. In this study, when using the sensitivity analysis and optimization techniques for moan-noise reduction, the frequency-response-function-based substructuring technique was performed to calculate the response of the modified coupled torsional beam axle module by considering the joint conditions and the transfer functions of the brake system. Highly sensitive design parameters regarding the response of the coupled torsional beam axle module were identified after the sensitivity analysis. The most sensitive design parameters were selected to enhance the efficiency and the robustness of optimization. The optimal values for the design variables were obtained by applying a progressive quadratic response surface method as a optimization algorithm. The application of an optimization technique was possible using the finite element model and the results of the finite element analysis from the previous study. After optimization, a prototype was re-designed, manufactured and tested. Finally, it was verified that the moan noise was reduced, as the natural frequency of 387 Hz for the coupled torsional beam axle module was moved to a higher frequency.
- 2 October 2013
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 22 (11) , 115007
Magnetorheological elastomer with stiffness-variable characteristics based on induced current applied to differential mount of vehicles
A differential mount with elastomers is installed to insulate vibration transmitted from the engine to the body through the propeller shaft. Since existing differential mounts adopt an elastomer of uniform stiffness, it is difficult to meet both the requirements for steering performance and driving comfort at the same time. In order to overcome this limitation, this study suggests a magnetorheological elastomer (MRE)-based stiffness-variable differential mount which allows the mount’s stiffness to vary reversibly or instantly. The stiffness-variable differential mount was designed with a new inner structure where a magnetic field can be induced in the MRE. Further, the geometry of the MRE was optimized by means of the response surface method to achieve a targeted level of stiffness. The variable performance of the stiffness-variable differential mount was evaluated with the dynamic stiffness when a current of 3 A (0.287 T) was applied. As a result, it was found that the average increase in dynamic stiffness was 4.41 kgf mm−1 over an excitation frequency range of 60–100 Hz, a critical point of variation for dynamic stiffness, and 3.60 kgf mm−1 over an excitation frequency range of less than 100 Hz.
- 2 October 2013
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 22 (11) , 115007
Magnetorheological elastomer with stiffness-variable characteristics based on induced current applied to differential mount of vehicles
A differential mount with elastomers is installed to insulate vibration transmitted from the engine to the body through the propeller shaft. Since existing differential mounts adopt an elastomer of uniform stiffness, it is difficult to meet both the requirements for steering performance and driving comfort at the same time. In order to overcome this limitation, this study suggests a magnetorheological elastomer (MRE)-based stiffness-variable differential mount which allows the mount’s stiffness to vary reversibly or instantly. The stiffness-variable differential mount was designed with a new inner structure where a magnetic field can be induced in the MRE. Further, the geometry of the MRE was optimized by means of the response surface method to achieve a targeted level of stiffness. The variable performance of the stiffness-variable differential mount was evaluated with the dynamic stiffness when a current of 3 A (0.287 T) was applied. As a result, it was found that the average increase in dynamic stiffness was 4.41 kgf mm−1 over an excitation frequency range of 60–100 Hz, a critical point of variation for dynamic stiffness, and 3.60 kgf mm−1 over an excitation frequency range of less than 100 Hz.
- 29 July 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 227 (10) , 1363-1376
Development of a new sound quality metric for evaluation of the interior noise in a passenger car using the logarithmic Mahalanobis distance
Previous methods for the evaluation of the sound quality in vehicle interiors focused on the linear regression analysis of subjective sound quality metrics using statistics and estimations of subjective sound quality values by neural networks. Recently, sound quality evaluation using subjective measures has focused on identifying sound quality metrics which can predict subjective responses. It has been used to study a variety of subjective measures such as the four parameters used by Zwicker, but it is difficult to identify highly correlated sound quality metrics with the jury test. The Mahalanobis distance is a useful method to reduce the number of dimensions and to develop measures based on the correlation between the various variables. In particular, the Mahalanobis distance can be used as a new sound quality metric because it can convert the sound quality that is represented by several measures to a single value. In this study, a new sound quality metric is suggested which employs the four parameters used by Zwicker and is based on the Mahalanobis distance in order to predict subjective responses in sound quality evaluation. In addition, in order to calculate the Mahalanobis distance more accurately, after using data from a number of vehicles, sound quality metrics were reselected to remove those that do not require correlation analyses between each metric. Finally, we verified that the logarithmic Mahalanobis distance can be used not only as a new sound quality metric through correlation analysis with a jury test but also as a criterion to determine the vehicle quality. In order to verify the reliability of the regression equation, arbitrary vehicle data are applied to the regression equation. The regression equation using the logarithmic Mahalanobis distance is validated by the listening results, and the regression results after applying arbitrary data are similar.
- 29 July 2013
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 227 (10) , 1363-1376
Development of a new sound quality metric for evaluation of the interior noise in a passenger car using the logarithmic Mahalanobis distance
Previous methods for the evaluation of the sound quality in vehicle interiors focused on the linear regression analysis of subjective sound quality metrics using statistics and estimations of subjective sound quality values by neural networks. Recently, sound quality evaluation using subjective measures has focused on identifying sound quality metrics which can predict subjective responses. It has been used to study a variety of subjective measures such as the four parameters used by Zwicker, but it is difficult to identify highly correlated sound quality metrics with the jury test. The Mahalanobis distance is a useful method to reduce the number of dimensions and to develop measures based on the correlation between the various variables. In particular, the Mahalanobis distance can be used as a new sound quality metric because it can convert the sound quality that is represented by several measures to a single value. In this study, a new sound quality metric is suggested which employs the four parameters used by Zwicker and is based on the Mahalanobis distance in order to predict subjective responses in sound quality evaluation. In addition, in order to calculate the Mahalanobis distance more accurately, after using data from a number of vehicles, sound quality metrics were reselected to remove those that do not require correlation analyses between each metric. Finally, we verified that the logarithmic Mahalanobis distance can be used not only as a new sound quality metric through correlation analysis with a jury test but also as a criterion to determine the vehicle quality. In order to verify the reliability of the regression equation, arbitrary vehicle data are applied to the regression equation. The regression equation using the logarithmic Mahalanobis distance is validated by the listening results, and the regression results after applying arbitrary data are similar.
- 29 January 2013
- Published by Korean Physical Society in Journal of the Korean Physical Society
- Vol. 62 (2) , 220-228
Magnetic-field-dependent shear modulus of a magnetorheological elastomer based on natural rubber
A magnetorheological elastomer (MRE) is a smart material that has a reversible and variable modulus in a magnetic field. Natural rubber, which has better physical properties than silicone matrices,...
- 29 January 2013
- Published by Korean Physical Society in Journal of the Korean Physical Society
- Vol. 62 (2) , 220-228
Magnetic-field-dependent shear modulus of a magnetorheological elastomer based on natural rubber
A magnetorheological elastomer (MRE) is a smart material that has a reversible and variable modulus in a magnetic field. Natural rubber, which has better physical properties than silicone matrices,...
- Open Access
- 20 January 2013
- Published by The Korean Society for Noise and Vibration Engineering in Transactions of the Korean Society for Noise and Vibration Engineering
- Vol. 23 (1) , 17-24
Comparison of Acceleration of Vibration Isolator and Accelerometer Attached Vibration Isolator Using Numerical Analysis
- 20 January 2013
- Published by The Korean Society for Noise and Vibration Engineering in Transactions of the Korean Society for Noise and Vibration Engineering
- Vol. 23 (1) , 17-24
Open AccessComparison of Acceleration of Vibration Isolator and Accelerometer Attached Vibration Isolator Using Numerical Analysis