Christopher D. P. Baxter
Research Subjects
Research Interests
Christopher D. P. Baxter has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Kathryn Moran
Technical Engineer, Ocean and Coastal Consultants, a COWI Company, Trumbull, CT 06611
4 shared publications - Aaron S. Bradshaw
Associate Professor, Charles E. Via, Jr. Department of Civil and Environmental Engineering, Virginia Tech, 120B Patton Hall, Blacksburg, VA, 24061
3 shared publications - Hans Vaziri
Technical Engineer, Ocean and Coastal Consultants, a COWI Company, Trumbull, CT 06611
3 shared publications Jian-Hua Wang
Associate Professor, Depts. of Ocean/Civil and Environmental Engineering, Univ. of Rhode Island, Narragansett, RI 02882
2 shared publications- M. S. Ravi Sharma
Ocean and Coastal Consultants Inc., A COWI Company 2 , Trumbull, Connecticut 06611, USA
2 shared publications - Raja Narayanasamy
Technical Engineer, Ocean and Coastal Consultants, a COWI Company, Trumbull, CT 06611
2 shared publications
Latest Publications
- 1 December 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (12) , 1202-1210
Strength of Weakly Cemented Sands from Drained Multistage Triaxial Tests
Characterizing the strength of weakly cemented and sensitive soils in the laboratory is difficult because of the difficulty in obtaining high-quality replicate samples necessary for defining the failure envelope. Multistage triaxial tests have long been used to reduce the variability caused by testing multiple samples; however, traditional criteria used for transitioning from one loading stage to another often lead to destructuring or failure in sensitive or structured soils. The objective of this paper is to present a methodology for conducting multistage drained triaxial tests on weakly cemented sands and estimating the resulting shear strength parameters. Both multistage and single-stage drained triaxial tests were performed on artificially cemented samples of a silty sand at two levels of densities and cementation. The use of dεv/dεa=0 as a termination criterion to move on to the next stage of loading and εv=0 as the failure criterion for the final stage of the shear resulted in an average error of 6%...
- 1 December 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (12) , 1202-1210
Strength of Weakly Cemented Sands from Drained Multistage Triaxial Tests
Characterizing the strength of weakly cemented and sensitive soils in the laboratory is difficult because of the difficulty in obtaining high-quality replicate samples necessary for defining the failure envelope. Multistage triaxial tests have long been used to reduce the variability caused by testing multiple samples; however, traditional criteria used for transitioning from one loading stage to another often lead to destructuring or failure in sensitive or structured soils. The objective of this paper is to present a methodology for conducting multistage drained triaxial tests on weakly cemented sands and estimating the resulting shear strength parameters. Both multistage and single-stage drained triaxial tests were performed on artificially cemented samples of a silty sand at two levels of densities and cementation. The use of dεv/dεa=0 as a termination criterion to move on to the next stage of loading and εv=0 as the failure criterion for the final stage of the shear resulted in an average error of 6%...
- 1 February 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (2) , 161-170
Use of A¯=0 as a Failure Criterion for Weakly Cemented Soils
There is considerable uncertainty in the determination of effective stress strength parameters of cemented soils from undrained triaxial tests. Large negative excess pore pressures are generated at relatively large strains (typically 4–5% for cemented silty sand) in isotropically consolidated undrained (CIU) tests, which results in gas coming out of solution during shear and significant variability in the measured peak deviator stress. In this study, different failure criteria for weakly cemented sands were evaluated based on the results of CIU and isotropically consolidated drained triaxial compression tests conducted on samples of artificially cemented sand. The use of A¯ =0 as a failure criterion eliminates the variability between the undrained tests and also ensures that the mobilized failure strength is not based on the highly variable negative excess pore pressures. In addition, the resulting strains to failure are comparable to the strains to failure for the drained tests. Mohr-Coulomb strength par...
- 1 February 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 137 (2) , 161-170
Use of A¯=0 as a Failure Criterion for Weakly Cemented Soils
There is considerable uncertainty in the determination of effective stress strength parameters of cemented soils from undrained triaxial tests. Large negative excess pore pressures are generated at relatively large strains (typically 4–5% for cemented silty sand) in isotropically consolidated undrained (CIU) tests, which results in gas coming out of solution during shear and significant variability in the measured peak deviator stress. In this study, different failure criteria for weakly cemented sands were evaluated based on the results of CIU and isotropically consolidated drained triaxial compression tests conducted on samples of artificially cemented sand. The use of A¯ =0 as a failure criterion eliminates the variability between the undrained tests and also ensures that the mobilized failure strength is not based on the highly variable negative excess pore pressures. In addition, the resulting strains to failure are comparable to the strains to failure for the drained tests. Mohr-Coulomb strength par...
- 14 May 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1-12
Sand Aging Field Study
Aging effects in sand, such as increases in penetration resistance with time after deposition, densification, and/or liquefaction, are known to occur in situ, but the causes of these effects are not fully understood. Nonetheless, these effects have important ramifications in earthquake engineering. First, the lack of understanding of the phenomenon is an impediment to quality assurance/quality control (QA/QC) for ground densification projects aimed at mitigating the damaging effects of liquefaction. This can be understood by considering that most liquefaction evaluation procedures correlate liquefaction susceptibility to in situ indices, such as penetration resistance (SPT and CPT) and small strain shear wave velocity (Vs), all of which are influenced by aging. Consequently, it is unclear as to how long after ground densification QA/QC in situ tests should be performed to ensure that the densification was sufficient to mitigate liquefaction susceptibility. Presented herein is an overview of an ongoing sand aging field study where liquefaction is being induced by explosives, vibrocompaction (using a vibroflot), and a NEES vibroseis in a heavily instrumented sand deposit. The state and properties of the sand are being monitored as a function of time after the disruption of the soil structure.
- 14 May 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 1-12
Sand Aging Field Study
Aging effects in sand, such as increases in penetration resistance with time after deposition, densification, and/or liquefaction, are known to occur in situ, but the causes of these effects are not fully understood. Nonetheless, these effects have important ramifications in earthquake engineering. First, the lack of understanding of the phenomenon is an impediment to quality assurance/quality control (QA/QC) for ground densification projects aimed at mitigating the damaging effects of liquefaction. This can be understood by considering that most liquefaction evaluation procedures correlate liquefaction susceptibility to in situ indices, such as penetration resistance (SPT and CPT) and small strain shear wave velocity (Vs), all of which are influenced by aging. Consequently, it is unclear as to how long after ground densification QA/QC in situ tests should be performed to ensure that the densification was sufficient to mitigate liquefaction susceptibility. Presented herein is an overview of an ongoing sand aging field study where liquefaction is being induced by explosives, vibrocompaction (using a vibroflot), and a NEES vibroseis in a heavily instrumented sand deposit. The state and properties of the sand are being monitored as a function of time after the disruption of the soil structure.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 522-529
The Effects of Basal Resistance and Hydroplaning on the Initial Kinematics of Seismically Induced Tsunamigenic Landslides
According to current landslide tsunami generation models, the initial acceleration time history of a submarine mass failure is an important factor influencing the source characteristics of tsunami waves. Translational models developed thus far typically simulate rigid or deforming bodies sliding down an inclined plane, assuming either negligible basal resistance or an idealized basal resistance, with or without the inclusion of hydrodynamic forces. However no known models incorporate realistic basal resistance, hydrodynamic forces, and hydroplaning together to quantify their effects on the initial kinematics of submarine failures. In all current models it is assumed that the maximum initial acceleration occurs nearly instantaneously after the moment of failure. Here, we propose a new rigid body model that incorporates hydrodynamic drag, with realistic basal resistance and hydroplaning effects. Utilizing the post failure shear strength of the sediment, this new model investigates the initial kinematics and time histories of the slide event in relation to tsunami generation over varying slope angles and idealized hydroplaning conditions. The current work is restricted to seismically induced submarine landslides in normally consolidated clay. The modeling results indicate a decrease in the magnitude of the peak slide acceleration by 27% to 47% and significant delays in the acceleration time histories of the sliding mass. The results also show an exponential increase in the delay of the acceleration time histories as the slope angle decreases, suggesting a greater influence of basal resistance and hydroplaning effects on typical submarine failures, for slopes of less than 5°. Further research is necessary to determine the influence of using the refined basal resistance models on predicted initial landslide tsunamis wave heights, lengths, and subsequent costal run-up elevations.
- 7 March 2008
- Published by American Society of Civil Engineers (ASCE)
- p. 522-529
The Effects of Basal Resistance and Hydroplaning on the Initial Kinematics of Seismically Induced Tsunamigenic Landslides
According to current landslide tsunami generation models, the initial acceleration time history of a submarine mass failure is an important factor influencing the source characteristics of tsunami waves. Translational models developed thus far typically simulate rigid or deforming bodies sliding down an inclined plane, assuming either negligible basal resistance or an idealized basal resistance, with or without the inclusion of hydrodynamic forces. However no known models incorporate realistic basal resistance, hydrodynamic forces, and hydroplaning together to quantify their effects on the initial kinematics of submarine failures. In all current models it is assumed that the maximum initial acceleration occurs nearly instantaneously after the moment of failure. Here, we propose a new rigid body model that incorporates hydrodynamic drag, with realistic basal resistance and hydroplaning effects. Utilizing the post failure shear strength of the sediment, this new model investigates the initial kinematics and time histories of the slide event in relation to tsunami generation over varying slope angles and idealized hydroplaning conditions. The current work is restricted to seismically induced submarine landslides in normally consolidated clay. The modeling results indicate a decrease in the magnitude of the peak slide acceleration by 27% to 47% and significant delays in the acceleration time histories of the sliding mass. The results also show an exponential increase in the delay of the acceleration time histories as the slope angle decreases, suggesting a greater influence of basal resistance and hydroplaning effects on typical submarine failures, for slopes of less than 5°. Further research is necessary to determine the influence of using the refined basal resistance models on predicted initial landslide tsunamis wave heights, lengths, and subsequent costal run-up elevations.
- 1 January 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 134 (1) , 37-46
Correlation between Cyclic Resistance and Shear-Wave Velocity for Providence Silts
As an alternative to a field-based liquefaction resistance approach, cyclic triaxial tests with bender elements were used to develop a new correlation between cyclic resistance ratio (CRR) and overburden stress-corrected shear-wave velocity ( VS1 ) for two nonplastic silts obtained from Providence, Rhode Island. Samples of natural nonplastic silt were recovered by block sampling and from geotechnical borings/split-spoon sampling. The data show that the correlation is independent of the soils’ stress history as well as the method used to prepare the silt for cyclic testing. The laboratory results indicate that using the existing field-based CRR- VS1 correlations will significantly overestimate the cyclic resistance of the Providence silts. The strong dependency of the CRR- VS1 curves on soil type also suggests the necessity of developing silt-specific liquefaction resistance curves from laboratory cyclic tests performed on reconstituted samples.
- 1 January 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 134 (1) , 37-46
Correlation between Cyclic Resistance and Shear-Wave Velocity for Providence Silts
As an alternative to a field-based liquefaction resistance approach, cyclic triaxial tests with bender elements were used to develop a new correlation between cyclic resistance ratio (CRR) and overburden stress-corrected shear-wave velocity ( VS1 ) for two nonplastic silts obtained from Providence, Rhode Island. Samples of natural nonplastic silt were recovered by block sampling and from geotechnical borings/split-spoon sampling. The data show that the correlation is independent of the soils’ stress history as well as the method used to prepare the silt for cyclic testing. The laboratory results indicate that using the existing field-based CRR- VS1 correlations will significantly overestimate the cyclic resistance of the Providence silts. The strong dependency of the CRR- VS1 curves on soil type also suggests the necessity of developing silt-specific liquefaction resistance curves from laboratory cyclic tests performed on reconstituted samples.
- 14 October 2007
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
A Site-Specific Comparison of Simplified Procedures for Evaluating Cyclic Resistance of Non-Plastic Silt
Assessing the liquefaction potential of silts is a challenging problem for practicing engineers. A common approach to performing such assessments is to apply a fines content "correction" factor to field-based correlations that were developed primarily for sands that relate cyclic resistance and in-situ indices (i.e., standard penetration test (SPT) N-value, cone penetration test (CPT) qc-value, or shear wave velocity (VS)). This paper compares the cyclic resistance estimated using these methods for a site in Providence, Rhode Island which is characterized by deep deposits of non-plastic silt. Standard penetration tests with energy measurements were performed in conjunction with seismic cone penetration tests, and representative samples were collected for laboratory testing. A site-specific VS-based cyclic resistance correlation was developed from cyclic triaxial tests with shear wave velocity measurements and was used as a baseline for comparing the results of current SPT- and CPT-based simplified approaches. The analysis suggests that the existing SPT- and CPT-based methods, provide reasonable predictions of cyclic resistance of the non-plastic silt when the recommended fines content corrections are applied.
- 14 October 2007
- Published by American Society of Civil Engineers (ASCE)
- p. 1-10
A Site-Specific Comparison of Simplified Procedures for Evaluating Cyclic Resistance of Non-Plastic Silt
Assessing the liquefaction potential of silts is a challenging problem for practicing engineers. A common approach to performing such assessments is to apply a fines content "correction" factor to field-based correlations that were developed primarily for sands that relate cyclic resistance and in-situ indices (i.e., standard penetration test (SPT) N-value, cone penetration test (CPT) qc-value, or shear wave velocity (VS)). This paper compares the cyclic resistance estimated using these methods for a site in Providence, Rhode Island which is characterized by deep deposits of non-plastic silt. Standard penetration tests with energy measurements were performed in conjunction with seismic cone penetration tests, and representative samples were collected for laboratory testing. A site-specific VS-based cyclic resistance correlation was developed from cyclic triaxial tests with shear wave velocity measurements and was used as a baseline for comparing the results of current SPT- and CPT-based simplified approaches. The analysis suggests that the existing SPT- and CPT-based methods, provide reasonable predictions of cyclic resistance of the non-plastic silt when the recommended fines content corrections are applied.
- 21 September 2007
- Published by American Society of Civil Engineers (ASCE)
A Case Study of Construction-Related Ground Movements in Providence Silt
In Providence, Rhode Island, there have been several instances where construction activities such as pile driving or excavation have caused significant movements of adjacent ground and nearby structures founded on non-plastic silts. This paper presents a case study documenting substantial and unusual movements of a braced excavation that were observed during construction of a pile-supported sewer structure. Both inclinometer and piezometer data are presented. The piezometer data suggest that the unusual ground movements were likely attributed to excess pore pressures that were generated during driving of H-piles at the bottom of the excavation. The field instrumentation data will be particularly useful in future modeling efforts to better understand the performance of foundations and braced excavations in the Providence silts.
- 21 September 2007
- Published by American Society of Civil Engineers (ASCE)
A Case Study of Construction-Related Ground Movements in Providence Silt
In Providence, Rhode Island, there have been several instances where construction activities such as pile driving or excavation have caused significant movements of adjacent ground and nearby structures founded on non-plastic silts. This paper presents a case study documenting substantial and unusual movements of a braced excavation that were observed during construction of a pile-supported sewer structure. Both inclinometer and piezometer data are presented. The piezometer data suggest that the unusual ground movements were likely attributed to excess pore pressures that were generated during driving of H-piles at the bottom of the excavation. The field instrumentation data will be particularly useful in future modeling efforts to better understand the performance of foundations and braced excavations in the Providence silts.
- 1 December 2006
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 132 (12) , 1574-1580
Correlation between Cyclic Resistance Ratios of Intact and Reconstituted Offshore Saturated Sands and Silts with the Same Shear Wave Velocity
The cyclic liquefaction resistance of intact medium dense specimens of sands and silts obtained from offshore platform sites was compared to that of specimens reconstituted to the same values of shear wave velocity. The shear wave velocity was measured using a new system that is comprised of torsional piezoelectric ceramic ring transducers mounted in a triaxial cell, a multiwave measuring device, and special watertight connectors. The relationship between cyclic resistance ratio and the number of cycles to liquefaction Nf of intact and reconstituted specimens was compared at the same values of consolidation pressure and shear wave velocity. There was good agreement between cyclic resistance ratios of intact and reconstituted specimens with similar values of shear wave velocity if liquefaction is defined as ⩽6% peak-to-peak axial strain. The results of this study support the hypothesis that the cyclic liquefaction resistance of reconstituted specimens may be restored to in situ conditions when their shear ...
- 1 December 2006
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 132 (12) , 1574-1580
Correlation between Cyclic Resistance Ratios of Intact and Reconstituted Offshore Saturated Sands and Silts with the Same Shear Wave Velocity
The cyclic liquefaction resistance of intact medium dense specimens of sands and silts obtained from offshore platform sites was compared to that of specimens reconstituted to the same values of shear wave velocity. The shear wave velocity was measured using a new system that is comprised of torsional piezoelectric ceramic ring transducers mounted in a triaxial cell, a multiwave measuring device, and special watertight connectors. The relationship between cyclic resistance ratio and the number of cycles to liquefaction Nf of intact and reconstituted specimens was compared at the same values of consolidation pressure and shear wave velocity. There was good agreement between cyclic resistance ratios of intact and reconstituted specimens with similar values of shear wave velocity if liquefaction is defined as ⩽6% peak-to-peak axial strain. The results of this study support the hypothesis that the cyclic liquefaction resistance of reconstituted specimens may be restored to in situ conditions when their shear ...
- 21 February 2006
- Published by American Society of Civil Engineers (ASCE)
- p. 1-6
Assessment of Formation Strength from Geophysical Well Logs Using Neural Networks
This paper presents the methodologies and results of two types of neural networks used to estimate the unconfined compressive strength (UCS) of weakly cemented sandstones from geophysical log data. The first neural network used 29 different logs as input and predicted UCS values at 8 cm depth resolution that were in good agreement with measured values. The second neural network used an innovative approach to improve the depth resolution and detection of thin bedding by relating changes in high resolution logs (e.g. bulk density or resistivity) to changes in strength. Preliminary analyses used to predict the undrained shear strength of marine clay illustrate the potential of this new approach for predicting the strength of weakly cemented sandstones.
- 21 February 2006
- Published by American Society of Civil Engineers (ASCE)
- p. 1-6
Assessment of Formation Strength from Geophysical Well Logs Using Neural Networks
This paper presents the methodologies and results of two types of neural networks used to estimate the unconfined compressive strength (UCS) of weakly cemented sandstones from geophysical log data. The first neural network used 29 different logs as input and predicted UCS values at 8 cm depth resolution that were in good agreement with measured values. The second neural network used an innovative approach to improve the depth resolution and detection of thin bedding by relating changes in high resolution logs (e.g. bulk density or resistivity) to changes in strength. Preliminary analyses used to predict the undrained shear strength of marine clay illustrate the potential of this new approach for predicting the strength of weakly cemented sandstones.
- 1 October 2004
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 130 (10) , 1051-1062
Experimental Study on the Aging of Sands
Aging effects in sand, such as increases in cone penetration resistance with time after deposition and/or densification, are known to occur in the field, but the causes of these effects are not fully understood. A laboratory testing program was designed to study mechanisms responsible for aging effects under controlled conditions. The testing program included measurements of the small strain shear modulus, electrical conductivity, pore fluid chemistry, and minicone penetration resistance after different periods of aging. Two different sands were tested, and aging effects were evaluated for different combinations of relative density, temperature, and pore fluid composition. Increases in the small strain shear modulus were observed throughout most of the tests, and chemical analyses suggest that precipitation of carbonate and silica occurred in two tests. Despite these changes, there was no corresponding increase in the minicone penetration resistance with time in any of the tests. It is unlikely that preci...
- 1 October 2004
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 130 (10) , 1051-1062
Experimental Study on the Aging of Sands
Aging effects in sand, such as increases in cone penetration resistance with time after deposition and/or densification, are known to occur in the field, but the causes of these effects are not fully understood. A laboratory testing program was designed to study mechanisms responsible for aging effects under controlled conditions. The testing program included measurements of the small strain shear modulus, electrical conductivity, pore fluid chemistry, and minicone penetration resistance after different periods of aging. Two different sands were tested, and aging effects were evaluated for different combinations of relative density, temperature, and pore fluid composition. Increases in the small strain shear modulus were observed throughout most of the tests, and chemical analyses suggest that precipitation of carbonate and silica occurred in two tests. Despite these changes, there was no corresponding increase in the minicone penetration resistance with time in any of the tests. It is unlikely that preci...