Charles W. Lenau
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Charles W. Lenau has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Robert M. O'Connell
Department of Electrical Engineering and Computer Science, University of Missouri, Columbia, MO, USA
2 shared publications - Henry Liu
Electrical and Computer Engineering Dept., Univ. of Missouri-Columbia, Columbia, MO 65211
1 shared publication Tuo Zhao
Dept. of Electrical and Computer Engineering, Univ. of Missouri, Columbia, MO 65211
1 shared publication
Latest Publications
- 1 May 2010
- Published by American Society of Civil Engineers (ASCE) in Journal of Pipeline Systems Engineering and Practice
- Vol. 1 (2) , 84-90
Capsule Separation by Linear Induction Motor in Pneumatic Capsule Pipeline Freight Transport System
In order to advance the state-of-the-art in pneumatic capsule pipeline (PCP) underground freight transportation science, this paper examines the problem of separating capsules that may naturally form into trains as they travel through the pipeline. Such separation of capsules is necessary when the capsule trains approach branching points in the system. The analysis is performed for the simplified case of a train consisting of two capsules in a typical 1.0 -m2 cross section PCP. The capsules enter and traverse a multisegmented linear induction motor (MSLIM) that is to be used to separate them prior to reaching the branching point. Separation distances and times have to be large enough to allow a switching operation to be performed on the first capsule before the second capsule arrives at the switching point. Results of the analysis show how the first capsule will accelerate and how the second capsule will decelerate, thus causing separation. The results also show that reasonable capsule-separation distance...
- 1 May 2010
- Published by American Society of Civil Engineers (ASCE) in Journal of Pipeline Systems Engineering and Practice
- Vol. 1 (2) , 84-90
Capsule Separation by Linear Induction Motor in Pneumatic Capsule Pipeline Freight Transport System
In order to advance the state-of-the-art in pneumatic capsule pipeline (PCP) underground freight transportation science, this paper examines the problem of separating capsules that may naturally form into trains as they travel through the pipeline. Such separation of capsules is necessary when the capsule trains approach branching points in the system. The analysis is performed for the simplified case of a train consisting of two capsules in a typical 1.0 -m2 cross section PCP. The capsules enter and traverse a multisegmented linear induction motor (MSLIM) that is to be used to separate them prior to reaching the branching point. Separation distances and times have to be large enough to allow a switching operation to be performed on the first capsule before the second capsule arrives at the switching point. Results of the analysis show how the first capsule will accelerate and how the second capsule will decelerate, thus causing separation. The results also show that reasonable capsule-separation distance...
- 1 January 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering
- Vol. 134 (1) , 50-58
Performance of Pneumatic Capsule Pipeline Freight Transport System Driven by Linear Motor
There is growing concern over the problems associated with excessive use of trucks to transport freight. Such problems include air and noise pollution, damage to road surfaces, excessive fuel consumption, traffic congestion, and accidents. Underground capsule freight pipelines promise to alleviate and solve these problems. This paper examines the steady-state performance of a pneumatic capsule pipeline (PCP) freight transport system based on the use of a nonintrusive linear electric motor (LEM) to propel the capsules. A PCP system consisting of a single LEM and a section of pipeline is described, and the equations that relate the various system variables are used in a MATLAB program to conduct a parametric performance study. The results suggest ways to optimize system performance without excessively increasing costs. For example, system mechanical efficiency greater than 90.0% can be obtained with a normalized motor length of the order of 2.0% if the pipe line fill rate is at least 20.0%, the pipe capsule speed is at least , the capsule length-to-diameter ratio is at most , the capsule mass per unit length is at most , and the end disk to motor-diameter ratio is at least 0.99. When these conditions are satisfied, the thrust per capsule required of the motor and the capsule speed in the motor are relatively insensitive to slight changes in motor length, pipe line fill rate, pipe capsule speed, capsule length or mass, or the drag coefficient in the pipe, results that should simplify the design of the motor.- 1 January 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering
- Vol. 134 (1) , 50-58
Performance of Pneumatic Capsule Pipeline Freight Transport System Driven by Linear Motor
There is growing concern over the problems associated with excessive use of trucks to transport freight. Such problems include air and noise pollution, damage to road surfaces, excessive fuel consumption, traffic congestion, and accidents. Underground capsule freight pipelines promise to alleviate and solve these problems. This paper examines the steady-state performance of a pneumatic capsule pipeline (PCP) freight transport system based on the use of a nonintrusive linear electric motor (LEM) to propel the capsules. A PCP system consisting of a single LEM and a section of pipeline is described, and the equations that relate the various system variables are used in a MATLAB program to conduct a parametric performance study. The results suggest ways to optimize system performance without excessively increasing costs. For example, system mechanical efficiency greater than 90.0% can be obtained with a normalized motor length of the order of 2.0% if the pipe line fill rate is at least 20.0%, the pipe capsule speed is at least , the capsule length-to-diameter ratio is at most , the capsule mass per unit length is at most , and the end disk to motor-diameter ratio is at least 0.99. When these conditions are satisfied, the thrust per capsule required of the motor and the capsule speed in the motor are relatively insensitive to slight changes in motor length, pipe line fill rate, pipe capsule speed, capsule length or mass, or the drag coefficient in the pipe, results that should simplify the design of the motor.