Iñigo Vegas
Research Subjects
Iñigo Vegas has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Moises Frias
Eduardo Torroja Institute for Construction Sciences, Spanish National Research Council (IETcc-CSIC), 28033 Madrid, Spain
8 shared publications - Jaime Moreno-Juez
TECNALIA, Basque Research and Technology Alliance (BRTA), Astondo Bidea, Edificio 700, Parque tecnológico de Bizkaia, 48160 Derio, Spain
3 shared publications - Raquel Vigil de la Villa
Departamento de Geología y Geoquímica, Geomateriales Unidad Asociada CSIC-UAM, Universidad Autónoma de Madrid, 28049 Madrid, Spain
3 shared publications - Ana Guerrero
Eduardo Torroja Institute for Construction Sciences, Spanish National Research Council (IETcc-CSIC), 28033 Madrid, Spain
2 shared publications - Ana María Moreno de Los Reyes
Eduardo Torroja Institute for Construction Sciences, Spanish National Research Council (IETcc-CSIC), 28033 Madrid, Spain
2 shared publications - Lucía Fernández-Carrasco
ATEM Research Group, Department of Civil and Environmental Engineering, Barcelona TECH, Universitat Politècnica de Catalunya, Barcelona, Spain
2 shared publications
Latest Publications
- 21 June 2026
- Published by Springer Nature
- p. 234-241
Effect of Accelerated Carbonation of Industrial Waste on Mechanical and Intrinsic Properties in Eco-Mortars
- 21 June 2026
- Published by Springer Nature
- p. 234-241
Effect of Accelerated Carbonation of Industrial Waste on Mechanical and Intrinsic Properties in Eco-Mortars
- Open Access
Effect of Use of Alkaline Waste Materials as a CO2 Sink on the Physical and Mechanical Performance of Eco-Blended Cement Mortars—Comparative Study
This research paper provides new insights into the impact of accelerated mineralization of alkaline waste materials on the physical and mechanical behavior of low-carbon cement-based mortars. Standardized eco-cement mortars were prepared by replacing Portland cement with 7% and 20% proportions of three alkaline waste materials (white ladle furnace slag, biomass ash, and fine concrete waste fraction) that had been previously carbonated in a static reactor at predefined humidity and CO2 concentration. The mortars’ physical (total/capillary water absorption, electrical resistivity) and mechanical properties (compressive strength up to 90 d of curing) were analyzed, and their microstructures were examined using mercury intrusion porosimetry and computed tomography. The results reveal that carbonated waste materials generate a greater heat of hydration and have a lower total and capillary water absorption capacity, while the electrical resistivity and compressive strength tests generally indicate that they behave similarly to mortars not containing carbonated minerals. Mercury intrusion porosimetry (microporosity) indicates an increase in total porosity, with no clear refinement versus non-carbonated materials, while computed tomography (macroporosity) reveals a refinement of the pore structure with a significant reduction in the number of larger pores (>0.09 mm3) and intermediate pores (0.001–0.09 mm3) when carbonated residues are incorporated that varies depending on waste material. The construction and demolition waste (CCDW-C) introduced the best physical and mechanical behavior. These studies confirm the possibility of recycling carbonated waste materials as low-carbon supplementary cementitious materials (SCMs).
Open AccessEffect of Use of Alkaline Waste Materials as a CO2 Sink on the Physical and Mechanical Performance of Eco-Blended Cement Mortars—Comparative Study
This research paper provides new insights into the impact of accelerated mineralization of alkaline waste materials on the physical and mechanical behavior of low-carbon cement-based mortars. Standardized eco-cement mortars were prepared by replacing Portland cement with 7% and 20% proportions of three alkaline waste materials (white ladle furnace slag, biomass ash, and fine concrete waste fraction) that had been previously carbonated in a static reactor at predefined humidity and CO2 concentration. The mortars’ physical (total/capillary water absorption, electrical resistivity) and mechanical properties (compressive strength up to 90 d of curing) were analyzed, and their microstructures were examined using mercury intrusion porosimetry and computed tomography. The results reveal that carbonated waste materials generate a greater heat of hydration and have a lower total and capillary water absorption capacity, while the electrical resistivity and compressive strength tests generally indicate that they behave similarly to mortars not containing carbonated minerals. Mercury intrusion porosimetry (microporosity) indicates an increase in total porosity, with no clear refinement versus non-carbonated materials, while computed tomography (macroporosity) reveals a refinement of the pore structure with a significant reduction in the number of larger pores (>0.09 mm3) and intermediate pores (0.001–0.09 mm3) when carbonated residues are incorporated that varies depending on waste material. The construction and demolition waste (CCDW-C) introduced the best physical and mechanical behavior. These studies confirm the possibility of recycling carbonated waste materials as low-carbon supplementary cementitious materials (SCMs).
- 9 June 2023
- Published by Springer Nature
- p. 14-22
Chemical and Mechanical Characterization of a Novel CSA Blended Cement Based on CDW Inorganic Fractions
- 9 June 2023
- Published by Springer Nature
- p. 14-22
Chemical and Mechanical Characterization of a Novel CSA Blended Cement Based on CDW Inorganic Fractions
- Open Access
Durability of Construction and Demolition Waste-Bearing Ternary Eco-Cements
In recent years, the development of ternary cements has become a priority research line for obtaining cements with a lower carbon footprint, with the goal to contribute to achieve climate neutrality by 2050. This study compared ordinary Portland cement (OPC) durability to the performance of ternary cements bearing OPC plus 7% of a 2:1 binary blend of either calcareous (Hc) or siliceous (Hs) concrete waste fines and shatterproof glass. Durability was measured further to the existing legislation for testing concrete water absorption, effective porosity, pressurized water absorption and resistance to chlorides and CO2. The experimental findings showed that the 7% blended mortars performed better than the reference cement in terms of total and effective porosity, but they absorbed more pressurized water. They also exhibited lower CO2 resistance, particularly in the calcareous blend, likely due to its higher porosity. Including the binary blend of CDW enhanced chloride resistance with diffusion coefficients of 2.9 × 10−11 m2 s−1 (calcareous fines-glass, 7%Hc-G) and 1.5 × 10−11 m2 s−1 (siliceous fines-glass, 7%Hs-G) compared to the reference cement’s 4.3 × 10−11 m2 s−1. The siliceous fines-glass blend out-performed the calcareous blend in all the durability tests. As the mortars with and without CDW (construction and demolition waste) performed to similar standards overall, the former were deemed viable for the manufacture of future eco-efficient cements.
Open AccessDurability of Construction and Demolition Waste-Bearing Ternary Eco-Cements
In recent years, the development of ternary cements has become a priority research line for obtaining cements with a lower carbon footprint, with the goal to contribute to achieve climate neutrality by 2050. This study compared ordinary Portland cement (OPC) durability to the performance of ternary cements bearing OPC plus 7% of a 2:1 binary blend of either calcareous (Hc) or siliceous (Hs) concrete waste fines and shatterproof glass. Durability was measured further to the existing legislation for testing concrete water absorption, effective porosity, pressurized water absorption and resistance to chlorides and CO2. The experimental findings showed that the 7% blended mortars performed better than the reference cement in terms of total and effective porosity, but they absorbed more pressurized water. They also exhibited lower CO2 resistance, particularly in the calcareous blend, likely due to its higher porosity. Including the binary blend of CDW enhanced chloride resistance with diffusion coefficients of 2.9 × 10−11 m2 s−1 (calcareous fines-glass, 7%Hc-G) and 1.5 × 10−11 m2 s−1 (siliceous fines-glass, 7%Hs-G) compared to the reference cement’s 4.3 × 10−11 m2 s−1. The siliceous fines-glass blend out-performed the calcareous blend in all the durability tests. As the mortars with and without CDW (construction and demolition waste) performed to similar standards overall, the former were deemed viable for the manufacture of future eco-efficient cements.
- 19 July 2015
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 226 (8) , 1-11
Forced Aging and Ionic Mobility of Ternary Cements Exposed to Aggressive Saline Marine Environments and Cryoclastic Processes
- 19 July 2015
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 226 (8) , 1-11
Forced Aging and Ionic Mobility of Ternary Cements Exposed to Aggressive Saline Marine Environments and Cryoclastic Processes
- 1 January 2015
- Published by American Concrete Institute
- Vol. 303, 133-146
Influence of Coal Mining By-Products on the New Blended Cement Properties
- 1 January 2015
- Published by American Concrete Institute
- Vol. 303, 133-146
Influence of Coal Mining By-Products on the New Blended Cement Properties
- 1 September 2012
- Published by Elsevier in Cement and Concrete Composites
- Vol. 34 (8) , 911-916
Quantitative correlations among textural characteristics of C–S–H gel and mechanical properties: Case of ternary Portland cements containing activated paper sludge and fly ash
- 1 September 2012
- Published by Elsevier in Cement and Concrete Composites
- Vol. 34 (8) , 911-916
Quantitative correlations among textural characteristics of C–S–H gel and mechanical properties: Case of ternary Portland cements containing activated paper sludge and fly ash
- 1 June 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 24 (6) , 666-673
Soil Stabilization with Calcined Paper Sludge: Laboratory and Field Tests
Two investigative stages are presented in this study, which aim to establish basic standards for the use of calcined paper sludge (CPS) in the stabilization of soils. The soils were stabilized with CPS and with mixtures of CPS and cement (C). The total percentage of binder was between 3 and 6% by weight. The blending ratios (by weight) of the CPS:C mixtures were 50∶50 and 25∶75. The first stage took place in the laboratory, and the second stage, in the field, involved in situ stabilization of 250 m of subgrade using dry-mix methods. The bearing capacity of the stabilized soils was determined in the laboratory. In the second stage, the densities of the subgrade were measured in the field following compaction and deflections at 7 days. Furthermore, the evolution of its unconfined compressive strength (UCS) was measured over 90 days. The results reveal optimal mechanical behavior of the stabilized soil at CPS:C ratios of approximately 25∶75.
- 1 June 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 24 (6) , 666-673
Soil Stabilization with Calcined Paper Sludge: Laboratory and Field Tests
Two investigative stages are presented in this study, which aim to establish basic standards for the use of calcined paper sludge (CPS) in the stabilization of soils. The soils were stabilized with CPS and with mixtures of CPS and cement (C). The total percentage of binder was between 3 and 6% by weight. The blending ratios (by weight) of the CPS:C mixtures were 50∶50 and 25∶75. The first stage took place in the laboratory, and the second stage, in the field, involved in situ stabilization of 250 m of subgrade using dry-mix methods. The bearing capacity of the stabilized soils was determined in the laboratory. In the second stage, the densities of the subgrade were measured in the field following compaction and deflections at 7 days. Furthermore, the evolution of its unconfined compressive strength (UCS) was measured over 90 days. The results reveal optimal mechanical behavior of the stabilized soil at CPS:C ratios of approximately 25∶75.
- 1 October 2008
- Published by Elsevier in Construction and Building Materials
- Vol. 22 (10) , 2031-2041
Mechanical expectations of a high performance concrete based on a polymer binder and reinforced with non-metallic rebars
- 1 October 2008
- Published by Elsevier in Construction and Building Materials
- Vol. 22 (10) , 2031-2041
Mechanical expectations of a high performance concrete based on a polymer binder and reinforced with non-metallic rebars