Farzad Tasbihgoo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Farzad Tasbihgoo has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Elgamal
UC San Diego
1 shared publication - Babak Moaveni
Department of Civil and Environmental Engineering, Tufts University, Medford, MA 02155, USA
1 shared publication - C. -M. Lin
Project Engineer, Englekirk Companies, 2116 Arlington Ave, Los Angeles, California 90018
1 shared publication - Daniel H. Whang
Professor, Dept. of Structural Engineering, Univ. of California at San Diego, 9500 Gilman Dr., La Jolla, CA 92093-0085
1 shared publication - Joel P. Conte
Univ. of California, 9500 Gilman Dr., San Diego
1 shared publication - John P. Caffrey
Associate Professor, Mechanical Engineering Dept., California State Polytechnic Univ., Pomona, CA 91768
1 shared publication
Latest Publications
- 7 December 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 114-124
Seismic Rehabilitation of Santa Monica Place Mall Based on ASCE 41
This paper presents the seismic design and remodeling of Santa Monica Place mall and its seismic strengthening following the guidelines of ASCE 41-06. The original building was designed as a closed roof mall based on the 1976 Uniform Building Code. The remodeled mall is designed to be an open roof mall with about same plan dimensions as existing mall. The existing mall is a steel frame with inverted Chevron (V-type) concentric braced frames in the N-S direction and CMU shear walls in the E-W direction. A nonlinear two-dimensional push-over analysis is conducted on representative braced frames to demonstrate nonlinear post-buckling capacity of Chevron braced frames. It is found that plastic rotation of the beam, where two braces intersect, at target displacement is less than the limits defined by ASCE 41-06. It was found that the existing braced frames have a lateral load carrying capacity greater than the demands according to the 1976 UBC and ASCE 41-06. To improve the seismic performance of the inverted braced frames, the beam in each frame that is intersected with the braces was strengthened. The strengthening scheme ensures that the expected post-buckling lateral load capacity exceeds the lateral shear demands.
- 7 December 2009
- Published by American Society of Civil Engineers (ASCE)
- p. 114-124
Seismic Rehabilitation of Santa Monica Place Mall Based on ASCE 41
This paper presents the seismic design and remodeling of Santa Monica Place mall and its seismic strengthening following the guidelines of ASCE 41-06. The original building was designed as a closed roof mall based on the 1976 Uniform Building Code. The remodeled mall is designed to be an open roof mall with about same plan dimensions as existing mall. The existing mall is a steel frame with inverted Chevron (V-type) concentric braced frames in the N-S direction and CMU shear walls in the E-W direction. A nonlinear two-dimensional push-over analysis is conducted on representative braced frames to demonstrate nonlinear post-buckling capacity of Chevron braced frames. It is found that plastic rotation of the beam, where two braces intersect, at target displacement is less than the limits defined by ASCE 41-06. It was found that the existing braced frames have a lateral load carrying capacity greater than the demands according to the 1976 UBC and ASCE 41-06. To improve the seismic performance of the inverted braced frames, the beam in each frame that is intersected with the braces was strengthened. The strengthening scheme ensures that the expected post-buckling lateral load capacity exceeds the lateral shear demands.
- 1 June 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 134 (6) , 1006-1015
Dynamic Testing of Alfred Zampa Memorial Bridge
This paper describes a set of dynamic field tests performed on the Alfred Zampa Memorial Bridge (AZMB), also known as the New Carquinez Bridge, which is located northeast of San Francisco on interstate Highway I-80. The AZMB, opened to traffic in November 2003, is the first suspension bridge in the United States with an orthotropic steel deck, reinforced concrete towers, and large-diameter drilled shaft foundations. The dynamic field tests described herein were conducted just before the bridge opening to traffic. They included ambient vibration tests, mainly wind induced, and forced vibration tests based on controlled traffic loads and vehicle-induced impact loads. Four different controlled traffic load patterns and seven different vehicle-induced impact load configurations were used in the forced vibration tests. The dynamic response of the bridge was measured through an array of 34 uniaxial and 10 triaxial force-balanced accelerometers deployed along the whole length of the bridge. These dynamic field tests provided a unique opportunity to determine the dynamic (modal) properties of the bridge in its as-built (baseline) condition with no previous traffic loads or seismic excitation. Such properties could be used to validate and/or update the finite element models used in the design phase of this bridge. They could also be used as baseline for future health monitoring studies of this bridge. At the end of the paper, the ambient vibration test data were used to identify the bridge modal parameters (natural frequencies, damping ratios, and mode shapes) using the data-driven stochastic subspace identification method.- 1 June 2008
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Engineering
- Vol. 134 (6) , 1006-1015
Dynamic Testing of Alfred Zampa Memorial Bridge
This paper describes a set of dynamic field tests performed on the Alfred Zampa Memorial Bridge (AZMB), also known as the New Carquinez Bridge, which is located northeast of San Francisco on interstate Highway I-80. The AZMB, opened to traffic in November 2003, is the first suspension bridge in the United States with an orthotropic steel deck, reinforced concrete towers, and large-diameter drilled shaft foundations. The dynamic field tests described herein were conducted just before the bridge opening to traffic. They included ambient vibration tests, mainly wind induced, and forced vibration tests based on controlled traffic loads and vehicle-induced impact loads. Four different controlled traffic load patterns and seven different vehicle-induced impact load configurations were used in the forced vibration tests. The dynamic response of the bridge was measured through an array of 34 uniaxial and 10 triaxial force-balanced accelerometers deployed along the whole length of the bridge. These dynamic field tests provided a unique opportunity to determine the dynamic (modal) properties of the bridge in its as-built (baseline) condition with no previous traffic loads or seismic excitation. Such properties could be used to validate and/or update the finite element models used in the design phase of this bridge. They could also be used as baseline for future health monitoring studies of this bridge. At the end of the paper, the ambient vibration test data were used to identify the bridge modal parameters (natural frequencies, damping ratios, and mode shapes) using the data-driven stochastic subspace identification method.