Robert K. Goldberg
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Robert K. Goldberg has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Wieslaw K. Binienda
Professor, Dept. of Civil Engineering, Univ. of Akron, Akron, OH 44325-3905
7 shared publications - Canio Hoffarth
School of Sustainable Engineering and the Built Environment, Arizona State Univ., 850 S. McAllister Ave., Tempe, AZ 85287
6 shared publications - Gunther Blankenhorn
Software Engineer, Livermore Software Technology Corporation, 7374 Los Positas Rd., Livermore, CA 94551
6 shared publications - Paul DuBois
Research Scientist, George Mason Univ., 4400 University Dr., Fairfax, VA 22030
6 shared publications - Subramaniam D. Rajan
Arizona State Univ
6 shared publications - Kelly S. Carney
Center for Collision Safety and Analysis, George Mason Univ., 4400 University Dr., Fairfax, VA 22030
4 shared publications
Latest Publications
- 21 September 2022
- Published by Morressier GmbH
Career Opportunities in Aerospace: Info and Mentoring
Learn how you can excel in your career and within the aerospace industry. This event will offer students and young professionals the opportunity |
- 21 September 2022
- Published by Morressier GmbH
Career Opportunities in Aerospace: Info and Mentoring
Learn how you can excel in your career and within the aerospace industry. This event will offer students and young professionals the opportunity |
- 1 May 2019
- Published by Elsevier in Composite Structures
- Vol. 215, 377-384
Micromechanical modeling of the effects of adiabatic heating on the high strain rate deformation of polymer matrix composites
- 1 May 2019
- Published by Elsevier in Composite Structures
- Vol. 215, 377-384
Micromechanical modeling of the effects of adiabatic heating on the high strain rate deformation of polymer matrix composites
- 15 November 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 678-687
Development and Verification of an Orthotropic Three-Dimensional Model with Tabulated Input Suitable for Use in Composite Impact Problems
The need for accurate material models to simulate the deformation, damage, and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased use in the aerospace and automotive communities. The aerospace community has identified several key capabilities which are currently lacking in the available material models in commercial transient dynamic finite element codes. To attempt to improve the predictive capability of composite impact simulations, a next generation material model is being developed for incorporation within the commercial transient dynamic finite element code LS-DYNA. The material model, which incorporates plasticity, damage, and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters such as modulus and strength. The plasticity portion of the orthotropic, three-dimensional, macroscopic composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function with a non-associative flow rule. For the damage model, a strain equivalent formulation is used in combination with a semi-coupled approach where the overall damage in a particular coordinate direction is assumed to be a function of the applied loads in all of the coordinate directions. For the failure model, a tabulated approach is utilized in which a stress or strain based invariant is defined as a function of the location of the current stress state in stress space to define the initiation of failure. The development and verification of the material model is discussed.
- 15 November 2018
- Published by American Society of Civil Engineers (ASCE)
- p. 678-687
Development and Verification of an Orthotropic Three-Dimensional Model with Tabulated Input Suitable for Use in Composite Impact Problems
The need for accurate material models to simulate the deformation, damage, and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased use in the aerospace and automotive communities. The aerospace community has identified several key capabilities which are currently lacking in the available material models in commercial transient dynamic finite element codes. To attempt to improve the predictive capability of composite impact simulations, a next generation material model is being developed for incorporation within the commercial transient dynamic finite element code LS-DYNA. The material model, which incorporates plasticity, damage, and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters such as modulus and strength. The plasticity portion of the orthotropic, three-dimensional, macroscopic composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function with a non-associative flow rule. For the damage model, a strain equivalent formulation is used in combination with a semi-coupled approach where the overall damage in a particular coordinate direction is assumed to be a function of the applied loads in all of the coordinate directions. For the failure model, a tabulated approach is utilized in which a stress or strain based invariant is defined as a function of the location of the current stress state in stress space to define the initiation of failure. The development and verification of the material model is discussed.
- 10 July 2018
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 52 (25) , 3445-3460
Implementation of a tabulated failure model into a generalized composite material model
The need for accurate material models to simulate the deformation, damage, and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased use in the aerospace and automotive communities. To attempt to improve the predictive capability of composite impact simulations, a next generation material model is being developed for incorporation within the commercial transient dynamic finite element code LS-DYNA. The material model, which incorporates plasticity, damage, and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters such as modulus and strength. The plasticity portion of the composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function. For the damage model, a strain equivalent formulation is used to allow for the uncoupling of the deformation and damage analyses. For the failure model, a tabulated approach is utilized in which a stress- or strain-based invariant is defined as a function of the location of the current stress state in stress space to define the initiation of failure. Failure surfaces can be defined with any arbitrary shape, unlike traditional failure models where the mathematical functions used to define the failure surface impose a specific shape on the failure surface. In the current paper, the complete development of the failure model is described and the generation of a tabulated failure surface for a representative composite material is discussed.
- 10 July 2018
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 52 (25) , 3445-3460
Implementation of a tabulated failure model into a generalized composite material model
The need for accurate material models to simulate the deformation, damage, and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased use in the aerospace and automotive communities. To attempt to improve the predictive capability of composite impact simulations, a next generation material model is being developed for incorporation within the commercial transient dynamic finite element code LS-DYNA. The material model, which incorporates plasticity, damage, and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters such as modulus and strength. The plasticity portion of the composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function. For the damage model, a strain equivalent formulation is used to allow for the uncoupling of the deformation and damage analyses. For the failure model, a tabulated approach is utilized in which a stress- or strain-based invariant is defined as a function of the location of the current stress state in stress space to define the initiation of failure. Failure surfaces can be defined with any arbitrary shape, unlike traditional failure models where the mathematical functions used to define the failure surface impose a specific shape on the failure surface. In the current paper, the complete development of the failure model is described and the generation of a tabulated failure surface for a representative composite material is discussed.
- 15 November 2017
- Published by DEStech Publications
Effects of Adiabatic Heating on the High Strain Rate Deformation of Polymer Matrix Composites
Polymer matrix composites (PMCs) are increasingly being used in aerospace structures that are expected to experience complex dynamic loading conditions throughout their lifetime. As such, a detailed understanding of the high strain rate behavior of the constituents, particularly the strain rate, temperature, and pressure dependent polymer matrix, is paramount. In this paper, preliminary efforts in modeling experimentally observed temperature rises due to plastic deformation in PMCs subjected to dynamic loading are presented. To this end, an existing isothermal viscoplastic polymer constitutive formulation is extended to model adiabatic conditions by incorporating temperature dependent elastic properties and modifying the components of the inelastic strain rate tensor to explicitly depend on temperature. It is demonstrated that the modified polymer constitutive model is capable of capturing strain rate and temperature dependent yield as well as thermal softening associated with the conversion of plastic work to heat at high rates of strain. The modified constitutive model is then embedded within a strength of materials based micromechanics framework to investigate the manifestation of matrix thermal softening, due to the conversion of plastic work to heat, on the high strain rate response of a T700/Epon 862 (T700/E862) unidirectional composite. Adiabatic model predictions for high strain rate composite longitudinal tensile, transverse tensile, and in-plane shear loading are presented. Results show a substantial deviation from isothermal conditions; significant thermal softening is observed for matrix dominated deformation modes (transverse tension and in-plane shear), highlighting the importance of accounting for the conversion of plastic work to heat in the polymer matrix in the high strain rate analysis of PMC structures.
- 15 November 2017
- Published by DEStech Publications
Effects of Adiabatic Heating on the High Strain Rate Deformation of Polymer Matrix Composites
Polymer matrix composites (PMCs) are increasingly being used in aerospace structures that are expected to experience complex dynamic loading conditions throughout their lifetime. As such, a detailed understanding of the high strain rate behavior of the constituents, particularly the strain rate, temperature, and pressure dependent polymer matrix, is paramount. In this paper, preliminary efforts in modeling experimentally observed temperature rises due to plastic deformation in PMCs subjected to dynamic loading are presented. To this end, an existing isothermal viscoplastic polymer constitutive formulation is extended to model adiabatic conditions by incorporating temperature dependent elastic properties and modifying the components of the inelastic strain rate tensor to explicitly depend on temperature. It is demonstrated that the modified polymer constitutive model is capable of capturing strain rate and temperature dependent yield as well as thermal softening associated with the conversion of plastic work to heat at high rates of strain. The modified constitutive model is then embedded within a strength of materials based micromechanics framework to investigate the manifestation of matrix thermal softening, due to the conversion of plastic work to heat, on the high strain rate response of a T700/Epon 862 (T700/E862) unidirectional composite. Adiabatic model predictions for high strain rate composite longitudinal tensile, transverse tensile, and in-plane shear loading are presented. Results show a substantial deviation from isothermal conditions; significant thermal softening is observed for matrix dominated deformation modes (transverse tension and in-plane shear), highlighting the importance of accounting for the conversion of plastic work to heat in the polymer matrix in the high strain rate analysis of PMC structures.
- 15 November 2017
- Published by DEStech Publications
Implementation of a Tabulated Failure Model into a Generalized Composite Material Model Suitable for Use in Impact Problems
The need for accurate material models to simulate the deformation, damage and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased use in the aerospace and automotive communities. The aerospace community has identified several key capabilities which are currently lacking in the available material models in commercial transient dynamic finite element codes. To attempt to improve the predictive capability of composite impact simulations, a next generation material model is being developed for incorporation within the commercial transient dynamic finite element code LSDYNA. The material model, which incorporates plasticity, damage and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters such as modulus and strength. The plasticity portion of the orthotropic, threedimensional, macroscopic composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function with a nonassociative flow rule. For the damage model, a strain equivalent formulation is used to allow for the uncoupling of the deformation and damage analyses. For the failure model, a tabulated approach is utilized in which a stress or strain based invariant is defined as a function of the location of the current stress state in stress space to define the initiation of failure. Failure surfaces can be defined with any arbitrary shape, unlike traditional failure models where the mathematical functions used to define the failure surface impose a specific shape on the failure surface. In the current paper, the complete development of the failure model is described and the generation of a tabulated failure surface for a representative composite material is discussed.
- 15 November 2017
- Published by DEStech Publications
Implementation of a Tabulated Failure Model into a Generalized Composite Material Model Suitable for Use in Impact Problems
The need for accurate material models to simulate the deformation, damage and failure of polymer matrix composites under impact conditions is becoming critical as these materials are gaining increased use in the aerospace and automotive communities. The aerospace community has identified several key capabilities which are currently lacking in the available material models in commercial transient dynamic finite element codes. To attempt to improve the predictive capability of composite impact simulations, a next generation material model is being developed for incorporation within the commercial transient dynamic finite element code LSDYNA. The material model, which incorporates plasticity, damage and failure, utilizes experimentally based tabulated input to define the evolution of plasticity and damage and the initiation of failure as opposed to specifying discrete input parameters such as modulus and strength. The plasticity portion of the orthotropic, threedimensional, macroscopic composite constitutive model is based on an extension of the Tsai-Wu composite failure model into a generalized yield function with a nonassociative flow rule. For the damage model, a strain equivalent formulation is used to allow for the uncoupling of the deformation and damage analyses. For the failure model, a tabulated approach is utilized in which a stress or strain based invariant is defined as a function of the location of the current stress state in stress space to define the initiation of failure. Failure surfaces can be defined with any arbitrary shape, unlike traditional failure models where the mathematical functions used to define the failure surface impose a specific shape on the failure surface. In the current paper, the complete development of the failure model is described and the generation of a tabulated failure surface for a representative composite material is discussed.
- 1 September 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 30 (5)
Using Virtual Tests to Complete the Description of a Three-Dimensional Orthotropic Material
Generalized constitutive models, which can be used in explicit finite-element analysis, are being developed to accurately model composite systems under impact conditions. These models require extensive characterization of the composite material as input—the more sophisticated the model, the larger the amount of required input data. The authors discuss details of the characterization data required for a generalized three-dimensional orthotropic elastoplastic material model that is under development to simulate the impact response of composite materials. The material response data are generated using virtual testing methods in an analytical approach based on the generalized method of cells and a finite-element system. These methods not only complement actual test data by providing an additional layer of verification for experimentally generated stress-strain curves; they also fill in gaps caused by lack of appropriate experimental data (due either to the required experiments not being carried out or to the experiments being too complex to carry out). Verification and validation test cases demonstrate the capabilities of the developed system and show how a general virtual testing framework can be used for characterizing orthotropic composites.
- 1 September 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 30 (5)
Using Virtual Tests to Complete the Description of a Three-Dimensional Orthotropic Material
Generalized constitutive models, which can be used in explicit finite-element analysis, are being developed to accurately model composite systems under impact conditions. These models require extensive characterization of the composite material as input—the more sophisticated the model, the larger the amount of required input data. The authors discuss details of the characterization data required for a generalized three-dimensional orthotropic elastoplastic material model that is under development to simulate the impact response of composite materials. The material response data are generated using virtual testing methods in an analytical approach based on the generalized method of cells and a finite-element system. These methods not only complement actual test data by providing an additional layer of verification for experimentally generated stress-strain curves; they also fill in gaps caused by lack of appropriate experimental data (due either to the required experiments not being carried out or to the experiments being too complex to carry out). Verification and validation test cases demonstrate the capabilities of the developed system and show how a general virtual testing framework can be used for characterizing orthotropic composites.
- Open Access
Verification and Validation of a Three-Dimensional Orthotropic Plasticity Constitutive Model Using a Unidirectional Composite
A three-dimensional constitutive model has been developed for modeling orthotropic composites subject to impact loads. It has three distinct components—a deformation model involving elastic and plastic deformations; a damage model; and a failure model. The model is driven by tabular data that is generated either using laboratory tests or via virtual testing. A unidirectional composite—T800/F3900, commonly used in the aerospace industry, is used in the verification and validation tests. While the failure model is under development, these tests indicate that the implementation of the deformation and damage models in a commercial finite element program, LS-DYNA, is efficient, robust and accurate.
Open AccessVerification and Validation of a Three-Dimensional Orthotropic Plasticity Constitutive Model Using a Unidirectional Composite
A three-dimensional constitutive model has been developed for modeling orthotropic composites subject to impact loads. It has three distinct components—a deformation model involving elastic and plastic deformations; a damage model; and a failure model. The model is driven by tabular data that is generated either using laboratory tests or via virtual testing. A unidirectional composite—T800/F3900, commonly used in the aerospace industry, is used in the verification and validation tests. While the failure model is under development, these tests indicate that the implementation of the deformation and damage models in a commercial finite element program, LS-DYNA, is efficient, robust and accurate.