Avadhesh Yadav
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Avadhesh Yadav has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
V. K. Bajpai
Department of Mechanical Engineering , National Institute of Technology , Kurukshetra, Haryana , 136119 , India
3 shared publications- Mohit Bhargva
Mechanical Engineering Department, Maharishi Markandeshwar (Deemed to Be) University, Mullana, India
2 shared publications V.K. Bajpai
Department of Mechanical Engineering , National Institute of Technology , Kurukshetra , Haryana , 136119 , India
2 shared publications- Himanshu Agrawal
National Institute of Technology Kurukshetra
1 shared publication Laxmikant Yadav
National Institute of Technology
1 shared publication- Manoj Kumar
Department of Mechanical Engineering, National Institute of Technology, Srinagar 190006, India
1 shared publication
Latest Publications
- 17 August 2021
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (39) , 54383-54402
Factors affecting the performance of a solar still and productivity enhancement methods: A review
Good-quality drinking water is an essential requirement for a healthy and sustainable future. In the current scenario, people living in remote areas of the world are deficient of potable water, especially in developing nations. Desalination technologies available today are energy intensive and aggravate carbon emissions as most energy requirements are fulfilled by using fossil fuels. Solar still is a simple and direct solar desalination device used for water distillation. The major problem associated with a solar still is its low productivity. The main aim of this review paper is to discuss various modifications in a solar still which resulted in productivity enhancement. Different parameters affecting a passive solar still performance and their optimum values for maximum productivity are also thoroughly analysed in this paper. Water depth is an important operating parameter that influences still productivity, and various results showed that maximum productivity is achieved mostly at minimum water depths.
- 17 August 2021
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 28 (39) , 54383-54402
Factors affecting the performance of a solar still and productivity enhancement methods: A review
Good-quality drinking water is an essential requirement for a healthy and sustainable future. In the current scenario, people living in remote areas of the world are deficient of potable water, especially in developing nations. Desalination technologies available today are energy intensive and aggravate carbon emissions as most energy requirements are fulfilled by using fossil fuels. Solar still is a simple and direct solar desalination device used for water distillation. The major problem associated with a solar still is its low productivity. The main aim of this review paper is to discuss various modifications in a solar still which resulted in productivity enhancement. Different parameters affecting a passive solar still performance and their optimum values for maximum productivity are also thoroughly analysed in this paper. Water depth is an important operating parameter that influences still productivity, and various results showed that maximum productivity is achieved mostly at minimum water depths.
- 20 February 2020
- Published by Springer Nature in Environment, Development and Sustainability
- Vol. 23 (2) , 1623-1645
A Scheffler solar concentrator heat transfer model used in forced-circulation ice melting system at high-altitude regions
- 20 February 2020
- Published by Springer Nature in Environment, Development and Sustainability
- Vol. 23 (2) , 1623-1645
A Scheffler solar concentrator heat transfer model used in forced-circulation ice melting system at high-altitude regions
- 21 January 2020
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 142 (3) , 1-20
Annual Performance Evaluation of Evacuated Tube Solar Air Collector With Phase Change Material
This manuscript has been presented to evaluate the annual performance of evacuated tube solar air collector (ETSAC) by using phase change material (PCM). The PCM (acetamide) simultaneously stores and exchange the heat to the air amid day hours. The heat stored by the PCM has been used to deliver hot air amid night hours. The performance of the system has been analyzed with circular fin configuration along with reflectors at 0.035kg s−1 air flow rate for twelve typical days. The performance of the system has been found excellent in the month of July.The maximum average temperature of PCM has been found to be as 87.8°C and the maximum average collector efficiency as 31.4%.
- 21 January 2020
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 142 (3) , 1-20
Annual Performance Evaluation of Evacuated Tube Solar Air Collector With Phase Change Material
This manuscript has been presented to evaluate the annual performance of evacuated tube solar air collector (ETSAC) by using phase change material (PCM). The PCM (acetamide) simultaneously stores and exchange the heat to the air amid day hours. The heat stored by the PCM has been used to deliver hot air amid night hours. The performance of the system has been analyzed with circular fin configuration along with reflectors at 0.035kg s−1 air flow rate for twelve typical days. The performance of the system has been found excellent in the month of July.The maximum average temperature of PCM has been found to be as 87.8°C and the maximum average collector efficiency as 31.4%.
- Open Access
- 1 August 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1276 (1) , 012042
Experimental investigation of single slope solar still using different wick materials: a comparative study
Solar still play an important role in mitigating potable water scarcity mainly in developing countries because of its low-cost and easy design. One major concern regarding solar still is the low productivity. Using a wick in still basin decreases active water depth and increases the evaporation rate of basin water. In the present work, a comparative study of single slope solar still using different wick materials is performed. Bamboo cotton, jute, wool, and cotton are used as wick materials. To carry out experiments, two single slope solar stills of similar dimensions are designed and constructed. Wick is placed over the rectangular shaped fins installed in the still basin. The experiments are conducted for 25 days and data collected on the clearest sunshine days are presented in this work. Water depth is kept constant at 1 cm throughout the experiments. Experimental results showed that maximum still productivity and efficiency is obtained using bamboo cotton wick as 3.03 l/m2day and 34.5% respectively. This is 16.9%, 20.7%, 37.8% and 51.9% higher than jute, cotton and wool wick and conventional still. It is evident from the experimental results that bamboo cotton is the most suitable wick material in comparison to others.
- 1 August 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1276 (1) , 012042
Open AccessExperimental investigation of single slope solar still using different wick materials: a comparative study
Solar still play an important role in mitigating potable water scarcity mainly in developing countries because of its low-cost and easy design. One major concern regarding solar still is the low productivity. Using a wick in still basin decreases active water depth and increases the evaporation rate of basin water. In the present work, a comparative study of single slope solar still using different wick materials is performed. Bamboo cotton, jute, wool, and cotton are used as wick materials. To carry out experiments, two single slope solar stills of similar dimensions are designed and constructed. Wick is placed over the rectangular shaped fins installed in the still basin. The experiments are conducted for 25 days and data collected on the clearest sunshine days are presented in this work. Water depth is kept constant at 1 cm throughout the experiments. Experimental results showed that maximum still productivity and efficiency is obtained using bamboo cotton wick as 3.03 l/m2day and 34.5% respectively. This is 16.9%, 20.7%, 37.8% and 51.9% higher than jute, cotton and wool wick and conventional still. It is evident from the experimental results that bamboo cotton is the most suitable wick material in comparison to others.
- Open Access
- 22 April 2014
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 50 (10) , 1465-1478
Comparative performance of desiccant wheel with effective and ordinary regeneration sector using mathematical model
- 22 April 2014
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 50 (10) , 1465-1478
Open AccessComparative performance of desiccant wheel with effective and ordinary regeneration sector using mathematical model
- 1 September 2013
- Published by Taylor & Francis in International Journal of Sustainable Engineering
- Vol. 6 (3) , 239-257
The performance of solar powered desiccant dehumidifier in India: an experimental investigation
The regeneration and adsorption of desiccant wheel for producing the dry air was experimentally investigated. The air needed for regeneration was heated in an evacuated tube solar collector with surface area 4.44 m2. The desiccant wheel is regenerated at the temperature in the range of 43.9–72.6°C. The regeneration and adsorption performances are affected by the regeneration temperature, wheel rotation, air flow rate (process and regeneration) and ambient conditions. By comparing the adsorption and regeneration performance at different air flow rate and constant rph, it was found that maximum adsorption and regeneration rates are obtained at air flow rate of 210.789 kg/h. Regeneration temperature directly affects the effectiveness of the desiccant wheel. Maximum desiccant wheel effectiveness of regeneration sector and adsorption sector is obtained at air flow rate of 105.394 kg/h. The regeneration performance of desiccant wheel with evacuated tube solar air collector is suitable for the Indian climate.
- 1 September 2013
- Published by Taylor & Francis in International Journal of Sustainable Engineering
- Vol. 6 (3) , 239-257
The performance of solar powered desiccant dehumidifier in India: an experimental investigation
The regeneration and adsorption of desiccant wheel for producing the dry air was experimentally investigated. The air needed for regeneration was heated in an evacuated tube solar collector with surface area 4.44 m2. The desiccant wheel is regenerated at the temperature in the range of 43.9–72.6°C. The regeneration and adsorption performances are affected by the regeneration temperature, wheel rotation, air flow rate (process and regeneration) and ambient conditions. By comparing the adsorption and regeneration performance at different air flow rate and constant rph, it was found that maximum adsorption and regeneration rates are obtained at air flow rate of 210.789 kg/h. Regeneration temperature directly affects the effectiveness of the desiccant wheel. Maximum desiccant wheel effectiveness of regeneration sector and adsorption sector is obtained at air flow rate of 105.394 kg/h. The regeneration performance of desiccant wheel with evacuated tube solar air collector is suitable for the Indian climate.
- 1 March 2013
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 34 (1) , 3-26
An experimental investigation of solar-powered desiccant wheel with different rotational speeds
Regeneration and adsorption rate of desiccant wheel for producing dry air have been experimentally investigated. The air needed for regeneration was heated in an evacuated tube solar collector with a surface area of 4.44 m2. The desiccant wheel is regenerated at a temperature range of 50–55°C. The regeneration and adsorption performances are affected by the regeneration temperature, wheel rotation, air flow rate (process and regeneration) and ambient conditions. On comparison, the adsorption and regeneration rates at different rotations per hour (rph) and at a constant flow rate of 210.789 kg/h for both adsorption sector and regeneration sector, it is found that in the range of 50–55°C average regeneration temperature, the solar-powered desiccant wheel performs well with a rotational speed of 16 rph. The regeneration performance of desiccant wheel with evacuated tube solar air collector is suitable for the Indian climatic conditions.
- 1 March 2013
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 34 (1) , 3-26
An experimental investigation of solar-powered desiccant wheel with different rotational speeds
Regeneration and adsorption rate of desiccant wheel for producing dry air have been experimentally investigated. The air needed for regeneration was heated in an evacuated tube solar collector with a surface area of 4.44 m2. The desiccant wheel is regenerated at a temperature range of 50–55°C. The regeneration and adsorption performances are affected by the regeneration temperature, wheel rotation, air flow rate (process and regeneration) and ambient conditions. On comparison, the adsorption and regeneration rates at different rotations per hour (rph) and at a constant flow rate of 210.789 kg/h for both adsorption sector and regeneration sector, it is found that in the range of 50–55°C average regeneration temperature, the solar-powered desiccant wheel performs well with a rotational speed of 16 rph. The regeneration performance of desiccant wheel with evacuated tube solar air collector is suitable for the Indian climatic conditions.
- 8 June 2012
- Published by Wiley in Chemical Engineering & Technology
- Vol. 35 (9) , 1617-1625
Mathematical Model for Design Parameter Analysis to Improve the Performance of a Desiccant Wheel
A mathematical model for estimating the optimum design parameters of a desiccant wheel in order to reduce weight and size has been developed. Heat and mass transfer from both moist air and desiccant material were considered in this model. The design parameters were analyzed under the basic operating condition of simulation. Channel height, pitch, and length of the desiccant wheel were optimized, as well as other design parameters such as area ratio, aspect ratio, and porosity.
- 8 June 2012
- Published by Wiley in Chemical Engineering & Technology
- Vol. 35 (9) , 1617-1625
Mathematical Model for Design Parameter Analysis to Improve the Performance of a Desiccant Wheel
A mathematical model for estimating the optimum design parameters of a desiccant wheel in order to reduce weight and size has been developed. Heat and mass transfer from both moist air and desiccant material were considered in this model. The design parameters were analyzed under the basic operating condition of simulation. Channel height, pitch, and length of the desiccant wheel were optimized, as well as other design parameters such as area ratio, aspect ratio, and porosity.
- 1 March 2012
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 33 (1) , 35-50
Thermal performance of one-ended evacuated tube solar air collector at different flow rates: experimental investigation
A solar-powered air heating system using one-ended normal evacuated tubes is experimentally investigated and used for heating. In this experimental setup, a header which works as a heat exchanger has been used. The header consists of a hollow pipe (circular pipe) in the centre through which the air flows. The experimental setup contains a fluid which works as a heat-collecting medium and collects the solar heat which falls on the tubes. This heat is delivered to the air flows through the circular pipe. To enhance the outlet temperature, copper coil and reflectors are used. Both configurations of parallel and counter flows are experimentally examined by changing the position of the blower. It is found that the setup operates more efficiently at high flow rate and counter flow, in the model with reflector and coil. The attained maximum temperate difference is found to be 36.8°C at a flow rate of 0.0268 kg/s.
- 1 March 2012
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 33 (1) , 35-50
Thermal performance of one-ended evacuated tube solar air collector at different flow rates: experimental investigation
A solar-powered air heating system using one-ended normal evacuated tubes is experimentally investigated and used for heating. In this experimental setup, a header which works as a heat exchanger has been used. The header consists of a hollow pipe (circular pipe) in the centre through which the air flows. The experimental setup contains a fluid which works as a heat-collecting medium and collects the solar heat which falls on the tubes. This heat is delivered to the air flows through the circular pipe. To enhance the outlet temperature, copper coil and reflectors are used. Both configurations of parallel and counter flows are experimentally examined by changing the position of the blower. It is found that the setup operates more efficiently at high flow rate and counter flow, in the model with reflector and coil. The attained maximum temperate difference is found to be 36.8°C at a flow rate of 0.0268 kg/s.