Abedin Zafari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Abedin Zafari has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
M.H. Kianmehr
Department of Agrotechnology, College of Abouraihan, University of Tehran, Tehran, Iran
1 shared publicationMohammad Hossein Kianmehr
Department of Agrotechnology, College of Abouraihan, University of Tehran, Tehran, Iran
1 shared publication- Mohammad Hossein Kianmehr
Univ Tehran, Coll Aburaihan, Dept Agrotechnol, Tehran, Iran
1 shared publication
Latest Publications
- 23 September 2013
- Published by Taylor & Francis in Environmental Technology
- Vol. 35 (4) , 478-486
Factors affecting mechanical properties of biomass pellet from compost
Effectiveness of a densification process to create strong and durable bonding in pellets can be determined by testing the mechanical properties such as compressive strength (CS) and durability. Mechanical properties of pellet from composted municipal solid waste were determined at different raw material and densification conditions. Ground compost samples were compressed with three levels of moisture content (35%, 40% and 45% (wb)), piston compaction speed (2, 6 and 10 mm/s), die length (8, 10 and 12 mm) and raw material particle size (0.3, 0.9 and 1.5 mm) into cylindrical pellets utilizing opened-end dies under axial stress from a vertical piston applied by a hydraulic press. The effects of independent variables on mechanical properties were determined using response surface methodology based on Box-Behnken design (BBD). All independent variables affected the durability significantly. However, different piston speed and die length not produce any significant difference on CS of pellets. Also in this research the electron photography method was used to identify the binding mechanism of compost particles.
- 23 September 2013
- Published by Taylor & Francis in Environmental Technology
- Vol. 35 (4) , 478-486
Factors affecting mechanical properties of biomass pellet from compost
Effectiveness of a densification process to create strong and durable bonding in pellets can be determined by testing the mechanical properties such as compressive strength (CS) and durability. Mechanical properties of pellet from composted municipal solid waste were determined at different raw material and densification conditions. Ground compost samples were compressed with three levels of moisture content (35%, 40% and 45% (wb)), piston compaction speed (2, 6 and 10 mm/s), die length (8, 10 and 12 mm) and raw material particle size (0.3, 0.9 and 1.5 mm) into cylindrical pellets utilizing opened-end dies under axial stress from a vertical piston applied by a hydraulic press. The effects of independent variables on mechanical properties were determined using response surface methodology based on Box-Behnken design (BBD). All independent variables affected the durability significantly. However, different piston speed and die length not produce any significant difference on CS of pellets. Also in this research the electron photography method was used to identify the binding mechanism of compost particles.
- 22 April 2013
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 31 (7) , 684-691
Application of densification process in organic waste management
Densification of biomass material that usually has a low density is good way of increasing density, reducing the cost of transportation, and simplifying the storage and distribution of this material. The current study was conducted to investigate the influence of raw material parameters (moisture content and particle size), and densification process parameters (piston speed and die length) on the density and durability of pellets from compost manure. A hydraulic press and a single pelleter were used to produce pellets in controlled conditions. Ground biomass samples were compressed with three levels of moisture content [35%, 40% and 45% (wet basis)], piston speed (2, 6 and 10 mm/s), die length (8, 10 and 12 mm) and particle size (0.3., 0.9 and 1.5 mm) to establish density and durability of pellets. A response surface methodology based on the Box Behnken design was used to study the responses pattern and to understand the influence of parameters. The results revealed that all independent variables have significant (P < 0.01) effects on studied responses in this research.
- 22 April 2013
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 31 (7) , 684-691
Application of densification process in organic waste management
Densification of biomass material that usually has a low density is good way of increasing density, reducing the cost of transportation, and simplifying the storage and distribution of this material. The current study was conducted to investigate the influence of raw material parameters (moisture content and particle size), and densification process parameters (piston speed and die length) on the density and durability of pellets from compost manure. A hydraulic press and a single pelleter were used to produce pellets in controlled conditions. Ground biomass samples were compressed with three levels of moisture content [35%, 40% and 45% (wet basis)], piston speed (2, 6 and 10 mm/s), die length (8, 10 and 12 mm) and particle size (0.3., 0.9 and 1.5 mm) to establish density and durability of pellets. A response surface methodology based on the Box Behnken design was used to study the responses pattern and to understand the influence of parameters. The results revealed that all independent variables have significant (P < 0.01) effects on studied responses in this research.
- Open Access
- 31 March 2012
- Published by Canadian Center of Science and Education in Journal of Agricultural Science
- Vol. 4 (5) , p203
Effect of Temperature, Pressure and Moisture Content on Durability of Cattle Manure Pellet in Open-end Die Method
Densification of biomass feedstocks, such as pelleting, can increase bulk density, improve storability, reduce transportation costs, and make these materials easier to handle by using existing handling and storage equipment. Evaluation effect of extrusion and raw material parameters on quality parameters of pellet is necessary to determine optimum conditions for designing and constructing a suitable pelleting machine for producing cattle manure pellets. In this study durability of cattle manure pellet that produced by opened die method determined at different temperatures (T), pressures (P) and moisture contents (M w ). Cattle manure samples were compressed with three levels of pressures (3.5,6 and 8 Mpa) and three levels of temperatures (40, 60 and 80 °C) at three levels of moisture contents (50, 55 and 60%). ANOVA results have indicated that linear terms T , P and Mw and interaction of variables were statistically signi?cant at P < 0.01 for pellet durability. Also using cattle manure with 50% moisture content, medium temperature about 40 °C and pressure at 6 MPa resulted maximum pellet durability.
- 31 March 2012
- Published by Canadian Center of Science and Education in Journal of Agricultural Science
- Vol. 4 (5) , p203
Open AccessEffect of Temperature, Pressure and Moisture Content on Durability of Cattle Manure Pellet in Open-end Die Method
Densification of biomass feedstocks, such as pelleting, can increase bulk density, improve storability, reduce transportation costs, and make these materials easier to handle by using existing handling and storage equipment. Evaluation effect of extrusion and raw material parameters on quality parameters of pellet is necessary to determine optimum conditions for designing and constructing a suitable pelleting machine for producing cattle manure pellets. In this study durability of cattle manure pellet that produced by opened die method determined at different temperatures (T), pressures (P) and moisture contents (M w ). Cattle manure samples were compressed with three levels of pressures (3.5,6 and 8 Mpa) and three levels of temperatures (40, 60 and 80 °C) at three levels of moisture contents (50, 55 and 60%). ANOVA results have indicated that linear terms T , P and Mw and interaction of variables were statistically signi?cant at P < 0.01 for pellet durability. Also using cattle manure with 50% moisture content, medium temperature about 40 °C and pressure at 6 MPa resulted maximum pellet durability.