Akihiro Ishimi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Akihiro Ishimi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Hirotaka Furuya
Faculty of Engineering, Kyushu University, Fukuoka, Japan
4 shared publicationsKozo Katsuyama
Department of Fuels and Materials, Japan Atomic Energy Agency, Ibaraki, Japan
4 shared publications- Ikken Sato
Japan Atomic Energy Agency
2 shared publications Koji Maeda
Fukushima Fuels and Materials Department, Japan Atomic Energy Agency, Ibaraki, Japan
2 shared publications- Toshio Nakagiri
Japan Atomic Energy Agency, International Research Institute for Nuclear Decommissioning, 4002 Narita, Oarai-machi, Higashi-Ibaraki-gun, Ibaraki-ken 311-1393, Japan
2 shared publications - Yuta Abe
Japan Atomic Energy Agency, 4002 Narita, Oarai-machi, Higashi-Ibaraki-gun, Ibaraki-ken 311-1393, Japan
2 shared publications
Latest Publications
- 29 January 2020
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 6 (2)
Development of Experimental Technology for Simulated Fuel-Assembly Heating to Address Core-Material-Relocation Behavior During Severe Accident
The authors are developing an experimental technology for simulating severe accident (SA) conditions using simulant fuel material (ZrO2) that would contribute, not only to Fukushima Daiichi (1 F) decommissioning, but also to enhance the safety of worldwide existing and future nuclear power plants through clarification of accident progression behavior. Nontransfer (NTR) type plasma, which has been in practical use with a large torch capacity as high as 2 MW, has the potential to heat subject materials to very high-temperatures without selecting the target to be heated. When simulating 1 F with SA code (Severe Core Damage Analysis Package (SCDAP), Methods for Estimation of Leakages and Consequences of Releases (MELCOR) and Modular Accident Analysis Program (MAAP)), the target of this core-material-melting and relocation (CMMR) experiment was to confirm that NTR plasma has a sufficient heating performance realizing large temperature gradients (>2000 K/m) expected under 1 F conditions. The authors selected NTR-type plasma-heating technology that has the advantage of continuous heating in addition to its high-temperature level. A prototype large-scale experiment (1 m × 0.3 m dia.), called CMMR-0, was conducted in 2016, in which a large temperature gradient was realized and basic characteristics of a heated test assembly were studied. However, the maximum temperature was limited in this test by the instability of the plasma torch under low-oxygen concentrations. It was clarified through this test that an improvement in plasma-heating technology was necessary to heat the large-scale test assembly. The CMMR-1/-2 experiments were carried out in 2017 with a test assembly similar to CMMR-0, applying the improved technology (higher heating power and controlled oxygen concentration). In these two tests, heating history was different, resulting in similar physical responses with more pronounced material melting and relocation in the CMMR-2 experiment. The CMMR-2 experiment was selected from the perspective of establishing an experimental technology. The CMMR-2 experiment adopted a 30-min heating period, wherein the power was increased to a level where a large temperature gradient was expected at the lower part of the core under actual 1 F accident conditions. Most of the control blade and channel box migrated from the original position. After heating, the simulated fuel assembly was measured by X-ray-computed tomography (CT) technology and by electron probe micro-analyzer (EPMA). CT pictures and elemental mapping demonstrated its excellent performance with rather good precision. Based on these results, an excellent perspective, in terms of applicability of the NTR-type plasma-heating technology to the SA experimental study, was obtained.
- 29 January 2020
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 6 (2)
Development of Experimental Technology for Simulated Fuel-Assembly Heating to Address Core-Material-Relocation Behavior During Severe Accident
The authors are developing an experimental technology for simulating severe accident (SA) conditions using simulant fuel material (ZrO2) that would contribute, not only to Fukushima Daiichi (1 F) decommissioning, but also to enhance the safety of worldwide existing and future nuclear power plants through clarification of accident progression behavior. Nontransfer (NTR) type plasma, which has been in practical use with a large torch capacity as high as 2 MW, has the potential to heat subject materials to very high-temperatures without selecting the target to be heated. When simulating 1 F with SA code (Severe Core Damage Analysis Package (SCDAP), Methods for Estimation of Leakages and Consequences of Releases (MELCOR) and Modular Accident Analysis Program (MAAP)), the target of this core-material-melting and relocation (CMMR) experiment was to confirm that NTR plasma has a sufficient heating performance realizing large temperature gradients (>2000 K/m) expected under 1 F conditions. The authors selected NTR-type plasma-heating technology that has the advantage of continuous heating in addition to its high-temperature level. A prototype large-scale experiment (1 m × 0.3 m dia.), called CMMR-0, was conducted in 2016, in which a large temperature gradient was realized and basic characteristics of a heated test assembly were studied. However, the maximum temperature was limited in this test by the instability of the plasma torch under low-oxygen concentrations. It was clarified through this test that an improvement in plasma-heating technology was necessary to heat the large-scale test assembly. The CMMR-1/-2 experiments were carried out in 2017 with a test assembly similar to CMMR-0, applying the improved technology (higher heating power and controlled oxygen concentration). In these two tests, heating history was different, resulting in similar physical responses with more pronounced material melting and relocation in the CMMR-2 experiment. The CMMR-2 experiment was selected from the perspective of establishing an experimental technology. The CMMR-2 experiment adopted a 30-min heating period, wherein the power was increased to a level where a large temperature gradient was expected at the lower part of the core under actual 1 F accident conditions. Most of the control blade and channel box migrated from the original position. After heating, the simulated fuel assembly was measured by X-ray-computed tomography (CT) technology and by electron probe micro-analyzer (EPMA). CT pictures and elemental mapping demonstrated its excellent performance with rather good precision. Based on these results, an excellent perspective, in terms of applicability of the NTR-type plasma-heating technology to the SA experimental study, was obtained.
- 26 July 2019
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 56 (11) , 981-987
Restructure behavior analysis in fast breeder reactor MOX fuel by X-ray CT
Both high- and low-density MOX fuel pellets of uranium and plutonium oxides were irradiated in the experimental fast reactor JOYO. After irradiation, these fuel pellets were examined by X-ray CT and their irradiation behavior was evaluated for formation of the central void. In particular, the central void size and temperature of fuel pellets at the beginning and end of irradiation were analyzed. The central voids in the low-density fuel pellets were bigger than those of the high-density fuel pellets at the same linear heating rate (LHR), and the threshold LHR and temperature at which the central voids were formed were lower than those of the high-density fuel pellets. It was understood from these results that the irradiation behaviors of high- and low-density fuel pellets were different.
- 26 July 2019
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 56 (11) , 981-987
Restructure behavior analysis in fast breeder reactor MOX fuel by X-ray CT
Both high- and low-density MOX fuel pellets of uranium and plutonium oxides were irradiated in the experimental fast reactor JOYO. After irradiation, these fuel pellets were examined by X-ray CT and their irradiation behavior was evaluated for formation of the central void. In particular, the central void size and temperature of fuel pellets at the beginning and end of irradiation were analyzed. The central voids in the low-density fuel pellets were bigger than those of the high-density fuel pellets at the same linear heating rate (LHR), and the threshold LHR and temperature at which the central voids were formed were lower than those of the high-density fuel pellets. It was understood from these results that the irradiation behaviors of high- and low-density fuel pellets were different.
- 5 March 2018
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 4 (2)
Application of Nontransfer Type Plasma Heating Technology for Core-Material-Relocation Tests in Boiling Water Reactor Severe Accident Conditions
A new experimental program using nontransfer (NTR) type plasma heating is under consideration in Japan Atomic Energy Agency (JAEA) to clarify the uncertainty on core-material relocation (CMR) behavior of boiling water reactor (BWR). In order to confirm the applicability of this new technology, authors performed preparatory plasma heating tests using small-scale test pieces (107 mm × 107 mm × 222 mm (height)). An excellent perspective in terms of applicability of the NTR plasma heating to melting high melting-temperature materials such as ZrO2 has been obtained. In addition, molten pool was formed at the middle height of the test piece indicating its capability to simulate the initial phase of core degradation behavior consistent with the real UO2 fuel PHEBUS fission products (FP) tests. Furthermore, application of electron probe micro-analyzer (EPMA), scanning electron microscope (SEM)/energy dispersive X-ray spectrometry (EDX), and X-ray computed tomography (CT) led to a conclusion that the pool formed consisted mainly of Zr with some concentration of oxygen which tended to be enhanced at the upper surface region of the pool. Based on these results, an excellent perspective in terms of applicability of the NTR plasma heating technology to the severe accident (SA) experimental study was obtained.
- 5 March 2018
- Published by ASME International in Journal of Nuclear Engineering and Radiation Science
- Vol. 4 (2)
Application of Nontransfer Type Plasma Heating Technology for Core-Material-Relocation Tests in Boiling Water Reactor Severe Accident Conditions
A new experimental program using nontransfer (NTR) type plasma heating is under consideration in Japan Atomic Energy Agency (JAEA) to clarify the uncertainty on core-material relocation (CMR) behavior of boiling water reactor (BWR). In order to confirm the applicability of this new technology, authors performed preparatory plasma heating tests using small-scale test pieces (107 mm × 107 mm × 222 mm (height)). An excellent perspective in terms of applicability of the NTR plasma heating to melting high melting-temperature materials such as ZrO2 has been obtained. In addition, molten pool was formed at the middle height of the test piece indicating its capability to simulate the initial phase of core degradation behavior consistent with the real UO2 fuel PHEBUS fission products (FP) tests. Furthermore, application of electron probe micro-analyzer (EPMA), scanning electron microscope (SEM)/energy dispersive X-ray spectrometry (EDX), and X-ray computed tomography (CT) led to a conclusion that the pool formed consisted mainly of Zr with some concentration of oxygen which tended to be enhanced at the upper surface region of the pool. Based on these results, an excellent perspective in terms of applicability of the NTR plasma heating technology to the severe accident (SA) experimental study was obtained.
- 3 August 2017
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 54 (11) , 1274-1276
Distributions of density and fission products in the reaction product between irradiated MOX fuel and molten zircaloy-2
Two- and three-dimensional images were obtained by X-ray CT in the reaction product between zircaloy-2 cladding tube and MOX fuel. The gamma-ray intensity distributions in the same specimen were also obtained by gamma-ray measurements of two fission products (Cs-137 and Eu-154) and one neutron-activated nuclide (Co-60). The average values of the fuel density (about 10.5 g/cm3) and the cladding density (about 6.55 g/cm3) were obtained in the metallic phase region by evaluation of the density distributions on two-dimensional X-ray CT images. The distributions of the crushed fuel pellet and the pores were also clearly observed in the three-dimensional X-ray CT images. The following results were found from the gamma-ray measurement. First, Cs-137 was observed in the unreacted fuel region and the pore region in the metallic phase region. Second, Eu-154 was widely distributed to all regions. Finally, Co-60 was confirmed only in the metallic phase region.
- 3 August 2017
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 54 (11) , 1274-1276
Distributions of density and fission products in the reaction product between irradiated MOX fuel and molten zircaloy-2
Two- and three-dimensional images were obtained by X-ray CT in the reaction product between zircaloy-2 cladding tube and MOX fuel. The gamma-ray intensity distributions in the same specimen were also obtained by gamma-ray measurements of two fission products (Cs-137 and Eu-154) and one neutron-activated nuclide (Co-60). The average values of the fuel density (about 10.5 g/cm3) and the cladding density (about 6.55 g/cm3) were obtained in the metallic phase region by evaluation of the density distributions on two-dimensional X-ray CT images. The distributions of the crushed fuel pellet and the pores were also clearly observed in the three-dimensional X-ray CT images. The following results were found from the gamma-ray measurement. First, Cs-137 was observed in the unreacted fuel region and the pore region in the metallic phase region. Second, Eu-154 was widely distributed to all regions. Finally, Co-60 was confirmed only in the metallic phase region.
- 17 September 2015
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 53 (7) , 951-956
Fuel performance of hollow pellets for fast breeder reactors
Three fuel rods containing hollow mixed oxide (MOX) pellets of uranium and plutonium oxides were fabricated and irradiated at a high linear heat rate (LHR) to burn-up of nearly 30,000 MWd/t in the experimental fast rector, JOYO MK-II. After irradiation, one of the fuel rod pellets was examined by X-ray CT and conventional nondestructive and destructive methods. Swelling rate was evaluated by both dimensional change and radial density distribution. There were no differences between both types of results and it was concluded that swelling rate can be examined in detail by the X-ray CT technique without dismantling the assembly. In addition, the swelling rate of hollow pellets was nearly the same as values reported for the fuel rods containing solid pellets. LHR was higher in the examined fuel rod containing hollow pellets than in the conventional fuel rod containing solid pellets, but fission gas release rates for both fuel rods were nearly the same.
- 17 September 2015
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 53 (7) , 951-956
Fuel performance of hollow pellets for fast breeder reactors
Three fuel rods containing hollow mixed oxide (MOX) pellets of uranium and plutonium oxides were fabricated and irradiated at a high linear heat rate (LHR) to burn-up of nearly 30,000 MWd/t in the experimental fast rector, JOYO MK-II. After irradiation, one of the fuel rod pellets was examined by X-ray CT and conventional nondestructive and destructive methods. Swelling rate was evaluated by both dimensional change and radial density distribution. There were no differences between both types of results and it was concluded that swelling rate can be examined in detail by the X-ray CT technique without dismantling the assembly. In addition, the swelling rate of hollow pellets was nearly the same as values reported for the fuel rods containing solid pellets. LHR was higher in the examined fuel rod containing hollow pellets than in the conventional fuel rod containing solid pellets, but fission gas release rates for both fuel rods were nearly the same.
- Open Access
- 20 November 2012
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 49 (12) , 1144-1155
Upgrading of X-ray CT technology for analyses of irradiated FBR MOX fuel
The X-ray CT technology previously developed by JAEA was upgraded. The shape of the X-ray source beam was changed from a circular shape to an elliptical one and the collimator slit width was decreased from 0.3 to 0.1 mm. The X-ray detector was improved by changing a CdWO4 scintillator to a highly sensitive silicon semiconductor detector. The analysis code of X-ray CT image was revised with respect to the number of points by using two kinds of experimental results and taking into account the effects of crack existence and deviation of the central void position from the radial center of a fuel pellet. As a result, high resolution X-ray CT images could be obtained on the transverse cross section of irradiated fuel assemblies. The error of the dimensional measurement was improved from ±0.1 to ±0.03 mm by upgrading the instrument and revising the analysis code of X-ray CT image. The discriminating accuracy of density difference could be increased, and the low density region (undisturbed region) and high density region (equi-axial and columnar regions) in the X-ray CT image on the cross section of irradiated fuel could be discriminated from each other. The reliability of fuel performance analysis improves because a large number of PIE data can be collected, compared with the conventional destructive PIE.
- 20 November 2012
- Published by Taylor & Francis in Journal of Nuclear Science and Technology
- Vol. 49 (12) , 1144-1155
Open AccessUpgrading of X-ray CT technology for analyses of irradiated FBR MOX fuel
The X-ray CT technology previously developed by JAEA was upgraded. The shape of the X-ray source beam was changed from a circular shape to an elliptical one and the collimator slit width was decreased from 0.3 to 0.1 mm. The X-ray detector was improved by changing a CdWO4 scintillator to a highly sensitive silicon semiconductor detector. The analysis code of X-ray CT image was revised with respect to the number of points by using two kinds of experimental results and taking into account the effects of crack existence and deviation of the central void position from the radial center of a fuel pellet. As a result, high resolution X-ray CT images could be obtained on the transverse cross section of irradiated fuel assemblies. The error of the dimensional measurement was improved from ±0.1 to ±0.03 mm by upgrading the instrument and revising the analysis code of X-ray CT image. The discriminating accuracy of density difference could be increased, and the low density region (undisturbed region) and high density region (equi-axial and columnar regions) in the X-ray CT image on the cross section of irradiated fuel could be discriminated from each other. The reliability of fuel performance analysis improves because a large number of PIE data can be collected, compared with the conventional destructive PIE.