Trevor John Cloete
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Trevor John Cloete has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Nicholas Daras
Blast Impact and Survivability Research Unit (BISRU), Department of Mechanical Engineering, University of Cape Town (UCT), Cape Town, South Africa
2 shared publications A. D. B. Yates
University of Cape Town
1 shared publicationClaire Victoria Rampersadh
Blast Impact and Survivability Research Unit (BISRU), Department of Mechanical Engineering, University of Cape Town, South Africa
1 shared publicationE. B. Ismail
Blast Impact and Survivability Research Unit (BISRU), University of Cape Town, Private bag X3, Rondebosch 7701, South Africa
1 shared publicationErnesto Bram Ismail
Centre for Research in Computational and Applied Mechanics (CERECAM), Department of Mechanical Engineering, UCT, South Africa
1 shared publicationG. Paul
Blast Impact and Survivability Research Unit (BISRU), University of Cape Town, Private bag X3, Rondebosch 7701, South Africa
1 shared publication
Latest Publications
- Open Access
- 21 June 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 46 (8) , 1-10
A novel quasi-static compression test set-up with micron order accuracy for small specimens
Accurate displacement measurements during compression tests on small specimens using large standard universal testing machines are adversely affected by the compliance of the apparatus. The influence of compliance becomes more acute when conducting tests on quasi-brittle materials, such as cortical bone, that exhibit low failure strains and for which accurate modulus values are required. This paper presents a custom compression test set-up (i.e., a subpress) that facilitates routine quasi-static compression tests on small specimens by eliminating the effect of testing machine compliance on the results. The displacement of the compression test set-up was recorded using a combination of Hall effect sensors and multipole magnetic strips, which offers a resolution of less than one micron. The results of quasi-static compression tests on small polymer specimens are reported where the displacements were measured using the custom compression test set-up, the integrated displacement measurement system of a universal testing machine and a visual extensometer. Additional tests on cortical bone specimens demonstrate the effectiveness of the compression test set-up. Based on the results, the compression test set-up appeared to yield more consistent and accurate measurements compared to both the integrated measurement system of a universal testing machine and a visual extensometer. Novel data regarding the incipient fracture of cortical bone were obtained. The compression test set-up allows for the routine testing of a large number of bone specimens with micron accuracy in a short time frame, thus reducing the effects of degradation on biological specimens.
- 21 June 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 46 (8) , 1-10
Open AccessA novel quasi-static compression test set-up with micron order accuracy for small specimens
Accurate displacement measurements during compression tests on small specimens using large standard universal testing machines are adversely affected by the compliance of the apparatus. The influence of compliance becomes more acute when conducting tests on quasi-brittle materials, such as cortical bone, that exhibit low failure strains and for which accurate modulus values are required. This paper presents a custom compression test set-up (i.e., a subpress) that facilitates routine quasi-static compression tests on small specimens by eliminating the effect of testing machine compliance on the results. The displacement of the compression test set-up was recorded using a combination of Hall effect sensors and multipole magnetic strips, which offers a resolution of less than one micron. The results of quasi-static compression tests on small polymer specimens are reported where the displacements were measured using the custom compression test set-up, the integrated displacement measurement system of a universal testing machine and a visual extensometer. Additional tests on cortical bone specimens demonstrate the effectiveness of the compression test set-up. Based on the results, the compression test set-up appeared to yield more consistent and accurate measurements compared to both the integrated measurement system of a universal testing machine and a visual extensometer. Novel data regarding the incipient fracture of cortical bone were obtained. The compression test set-up allows for the routine testing of a large number of bone specimens with micron accuracy in a short time frame, thus reducing the effects of degradation on biological specimens.
- Open Access
- 20 June 2024
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 157, 106632
Degradation of the mechanical properties of cortical bone due to long duration storage
- 20 June 2024
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 157, 106632
Open AccessDegradation of the mechanical properties of cortical bone due to long duration storage
- Open Access
- 21 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1133
Influence of Ball Bearing Size on the Flight and Damage Characteristics of Blast-Driven Ball Bearings
This paper presents insights into the influence of ball size on the flight characteristics and damage of a ball bearing embedded in a rear detonated cylindrical charge. It includes results from a post-test damage analysis of ball bearings from previously reported experiments. Computational simulations using Ansys Autodyn were used to provide extra information about the velocity variation during flight and the damage sustained by the ball bearings during the blast event. The influence of bearing size (diameter and mass) was investigated using the validated simulation models to extend the dataset beyond the initial experimental work. The peak bearing velocity is influenced by the charge mass to ball bearing mass ratio and the aspect ratio of the charge. Larger ball bearings require extra momentum to accelerate them to higher velocities, but their higher surface area means a greater portion of the explosive charge is involved in transferring kinetic energy to the projectile. Tensile spalling was to be the major damage mechanism within the ball bearings. The charge aspect ratio also influenced the hydrostatic pressure propagation within the ball bearing itself, affecting the location and degree of internal cracking within the bearings. These findings will prove valuable to blast protection engineers considering the effects of embedded projectiles in improvised explosive devices.
- 21 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (3) , 1133
Open AccessInfluence of Ball Bearing Size on the Flight and Damage Characteristics of Blast-Driven Ball Bearings
This paper presents insights into the influence of ball size on the flight characteristics and damage of a ball bearing embedded in a rear detonated cylindrical charge. It includes results from a post-test damage analysis of ball bearings from previously reported experiments. Computational simulations using Ansys Autodyn were used to provide extra information about the velocity variation during flight and the damage sustained by the ball bearings during the blast event. The influence of bearing size (diameter and mass) was investigated using the validated simulation models to extend the dataset beyond the initial experimental work. The peak bearing velocity is influenced by the charge mass to ball bearing mass ratio and the aspect ratio of the charge. Larger ball bearings require extra momentum to accelerate them to higher velocities, but their higher surface area means a greater portion of the explosive charge is involved in transferring kinetic energy to the projectile. Tensile spalling was to be the major damage mechanism within the ball bearings. The charge aspect ratio also influenced the hydrostatic pressure propagation within the ball bearing itself, affecting the location and degree of internal cracking within the bearings. These findings will prove valuable to blast protection engineers considering the effects of embedded projectiles in improvised explosive devices.
- Open Access
- 9 September 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 250, 05008
Deformation and damage characteristics of ball bearings under blast loading
This paper presents the unique failure characteristics, such as fragmentation, internal cracks, general deformation and pitting, observed on a SS420C ball bearing from direct blast loading using a cylindrical PE-4 explosive. Axisymmetric simulations were performed to gain insights of the failure mechanisms. While additional work is needed to fully understand all characteristic found, valuable findings have been presented to explain some of the failures.
- 9 September 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 250, 05008
Open AccessDeformation and damage characteristics of ball bearings under blast loading
This paper presents the unique failure characteristics, such as fragmentation, internal cracks, general deformation and pitting, observed on a SS420C ball bearing from direct blast loading using a cylindrical PE-4 explosive. Axisymmetric simulations were performed to gain insights of the failure mechanisms. While additional work is needed to fully understand all characteristic found, valuable findings have been presented to explain some of the failures.
- Open Access
- 9 September 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 250, 01004
Extending the annular in-plane torsional shear test specimen to applications at high strain rates
In-plane torsional shear testing is a well-established material testing technique in the metal forming community. The corresponding specimen is designed to be machined from sheet metal with a continuous annular shear zone intended to deform in simple shear. Consequently, there are no geometric discontinuities or “edge-effects” to induce volumetric changes or instabilities with the result that large true plastic strains up to 1.0 can be achieved. This paper presents an extension of the in-plane torsional shear test to the dynamic regime. Dynamic experiments were performed using a torsional split Hopkinson bar (TSHB) on specimens manufactured from Al 1050 H14. The experimental results show that the adopted technique can be used to determine the material behavior accurately and reliably in the dynamic regime.
- 9 September 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 250, 01004
Open AccessExtending the annular in-plane torsional shear test specimen to applications at high strain rates
In-plane torsional shear testing is a well-established material testing technique in the metal forming community. The corresponding specimen is designed to be machined from sheet metal with a continuous annular shear zone intended to deform in simple shear. Consequently, there are no geometric discontinuities or “edge-effects” to induce volumetric changes or instabilities with the result that large true plastic strains up to 1.0 can be achieved. This paper presents an extension of the in-plane torsional shear test to the dynamic regime. Dynamic experiments were performed using a torsional split Hopkinson bar (TSHB) on specimens manufactured from Al 1050 H14. The experimental results show that the adopted technique can be used to determine the material behavior accurately and reliably in the dynamic regime.
- Open Access
- 9 September 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 250, 06003
A multispecies investigation of the strain rate sensitivity of the modulus of cortical bone
The stiffness of cortical bone shows both inter- and intra-species variation. Currently, it is unclear whether this variation is due to differing testing protocols or an inherent feature of the material. Additionally, there is a lack of literature dealing with species other than human and bovine, particularly in the intermediate strain rate regime. In this study, cortical bone specimens were machined from the femurs of four species: baboon, crocodile, sheep and ostrich. Specimens were tested in the quasi-static and intermediate strain rate regimes using consistent testing protocols implemented by a single researcher. The results show a similar strain rate dependence for all species, i.e. the modulus shows negligible rate effects in the quasi-static regime, but a significant increase when moving to intermediate strain rates. This suggests that while the stiffness of the bone is species dependent, the effect of strain rate may be species independent. The observed intra- and inter-species variation is less than that reported in literature, highlighting the importance of a consistent testing protocol in multi-species studies.
- 9 September 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 250, 06003
Open AccessA multispecies investigation of the strain rate sensitivity of the modulus of cortical bone
The stiffness of cortical bone shows both inter- and intra-species variation. Currently, it is unclear whether this variation is due to differing testing protocols or an inherent feature of the material. Additionally, there is a lack of literature dealing with species other than human and bovine, particularly in the intermediate strain rate regime. In this study, cortical bone specimens were machined from the femurs of four species: baboon, crocodile, sheep and ostrich. Specimens were tested in the quasi-static and intermediate strain rate regimes using consistent testing protocols implemented by a single researcher. The results show a similar strain rate dependence for all species, i.e. the modulus shows negligible rate effects in the quasi-static regime, but a significant increase when moving to intermediate strain rates. This suggests that while the stiffness of the bone is species dependent, the effect of strain rate may be species independent. The observed intra- and inter-species variation is less than that reported in literature, highlighting the importance of a consistent testing protocol in multi-species studies.
- 10 September 2018
- Published by Springer Nature in The European Physical Journal Special Topics
- Vol. 227 (1-2) , 99-109
Strain rate and triaxiality effects on the dynamic ductile damage of DOMEX 355MC
- 10 September 2018
- Published by Springer Nature in The European Physical Journal Special Topics
- Vol. 227 (1-2) , 99-109
Strain rate and triaxiality effects on the dynamic ductile damage of DOMEX 355MC
- 15 September 2016
- Published by SAGE Publications in International Journal of Protective Structures
- Vol. 7 (3) , 367-388
Blast characterization using a ballistic pendulum with a centrally mounted Hopkinson bar
A series of laboratory-scale blast characterization experiments are presented to show the degree to which two alternative configurations of an instrumented ballistic pendulum can provide an ideal impulsive load. Both the total impulses and blast pressure histories were captured, the latter using a centrally mounted Hopkinson bar. Repeatable and consistent total impulse values were achieved, while the Hopkinson bar technique was sufficient to capture the essential shape of the blast loads, although the fine detail of the peak pressure could not be resolved due to higher mode dispersion. A short stand-off configuration produced short duration blast loads that approached an ideal impulsive load condition with near uniform impulse distributions, although the blast pressure distributions were non-uniform. Conversely, a blast tube configuration produced blast loads with near uniform pressure and impulse distributions but did not approach an ideal impulsive load condition, that is, the pressure history must be accounted for in subsequent analytical work.
- 15 September 2016
- Published by SAGE Publications in International Journal of Protective Structures
- Vol. 7 (3) , 367-388
Blast characterization using a ballistic pendulum with a centrally mounted Hopkinson bar
A series of laboratory-scale blast characterization experiments are presented to show the degree to which two alternative configurations of an instrumented ballistic pendulum can provide an ideal impulsive load. Both the total impulses and blast pressure histories were captured, the latter using a centrally mounted Hopkinson bar. Repeatable and consistent total impulse values were achieved, while the Hopkinson bar technique was sufficient to capture the essential shape of the blast loads, although the fine detail of the peak pressure could not be resolved due to higher mode dispersion. A short stand-off configuration produced short duration blast loads that approached an ideal impulsive load condition with near uniform impulse distributions, although the blast pressure distributions were non-uniform. Conversely, a blast tube configuration produced blast loads with near uniform pressure and impulse distributions but did not approach an ideal impulsive load condition, that is, the pressure history must be accounted for in subsequent analytical work.
- 25 January 2016
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 2 (1) , 50-58
A Tandem Momentum Trap for Dynamic Specimen Recovery During Split Hopkinson Pressure Bar Testing of Cancellous Bone
- 25 January 2016
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 2 (1) , 50-58
A Tandem Momentum Trap for Dynamic Specimen Recovery During Split Hopkinson Pressure Bar Testing of Cancellous Bone
- 13 May 2014
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 372 (2015) , 20130210
Hopkinson bar techniques for the intermediate strain rate testing of bovine cortical bone
Detailed knowledge of the dynamic viscoelastic properties of bone is required to understand the mechanisms of macroscopic bone fracture in humans, and other terrestrial mammals, during impact loading events (e.g. falls, vehicle accidents, etc.). While the dynamic response of bone has been studied for several decades, high-quality data remain limited, and it is only within the last decade that techniques for conducting dynamic compression tests on bone at near-constant strain rates have been developed. Furthermore, there appears to be a lack of published bone data in the intermediate strain rate (ISR) range (i.e. 1–100 s −1 ), which represents a regime in which many dynamic bone fractures occur. In this paper, preliminary results for the dynamic compression of bovine cortical bone in the ISR regime are presented. The results are obtained using two Hopkinson-bar-related techniques, namely the conventional split Hopkinson bar arrangement incorporating a novel cone-in-tube striker design, and the recently developed wedge bar apparatus. The experimental results show a rapid transition in the strain rate sensitive behaviour of bovine cortical bone in the ISR range. Finally, a new viscoelastic model is proposed that captures the observed transition behaviour.
- 13 May 2014
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 372 (2015) , 20130210
Hopkinson bar techniques for the intermediate strain rate testing of bovine cortical bone
Detailed knowledge of the dynamic viscoelastic properties of bone is required to understand the mechanisms of macroscopic bone fracture in humans, and other terrestrial mammals, during impact loading events (e.g. falls, vehicle accidents, etc.). While the dynamic response of bone has been studied for several decades, high-quality data remain limited, and it is only within the last decade that techniques for conducting dynamic compression tests on bone at near-constant strain rates have been developed. Furthermore, there appears to be a lack of published bone data in the intermediate strain rate (ISR) range (i.e. 1–100 s −1 ), which represents a regime in which many dynamic bone fractures occur. In this paper, preliminary results for the dynamic compression of bovine cortical bone in the ISR regime are presented. The results are obtained using two Hopkinson-bar-related techniques, namely the conventional split Hopkinson bar arrangement incorporating a novel cone-in-tube striker design, and the recently developed wedge bar apparatus. The experimental results show a rapid transition in the strain rate sensitive behaviour of bovine cortical bone in the ISR range. Finally, a new viscoelastic model is proposed that captures the observed transition behaviour.