Juha Virtanen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Juha Virtanen has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Lauri Sydanheimo
Faculty of Medicine and Health Technology, Tampere University, Tampere, Finland
2 shared publications A. Z. Elsherbeni
Department of Electrical Engineering, University of Mississippi, Oxford, MS 38677, USA
1 shared publicationJ. Virkki
Department of Electronics, Rauma Research Unit, Tampere University of Technology, 33720 Tampere, Finland
1 shared publicationL. Ukkonen
Department of Electronics, Rauma Research Unit, Tampere University of Technology, 33720 Tampere, Finland
1 shared publication- Leena Ukkonen
Faculty of Medicine and Health Technology, Tampere University, Tampere, Finland
1 shared publication - Toni Bjorninen
Tampere University
1 shared publication
Latest Publications
- Open Access
- 1 January 2012
- Published by Hindawi Limited in International Journal of Antennas and Propagation
- Vol. 2012, 1-9
A Selective Ink Deposition Method for the Cost-Performance Optimization of Inkjet-Printed UHF RFID Tag Antennas
A selective ink deposition method is proposed for fabricating inkjet-printed passive UHF RFID tag antennas with optimized cost-performance ratios. The deposition method is based on identifying areas with high surface current densities on a given tag antenna and applying additional silver nanoparticle ink onto such areas to increase tag read range. In this paper, the proposed method is experimentally verified by utilizing the method on a small dipole tag antenna. Several ink deposition schemes are created, and their read range performances and ink consumptions are presented.
- 1 January 2012
- Published by Hindawi Limited in International Journal of Antennas and Propagation
- Vol. 2012, 1-9
Open AccessA Selective Ink Deposition Method for the Cost-Performance Optimization of Inkjet-Printed UHF RFID Tag Antennas
A selective ink deposition method is proposed for fabricating inkjet-printed passive UHF RFID tag antennas with optimized cost-performance ratios. The deposition method is based on identifying areas with high surface current densities on a given tag antenna and applying additional silver nanoparticle ink onto such areas to increase tag read range. In this paper, the proposed method is experimentally verified by utilizing the method on a small dipole tag antenna. Several ink deposition schemes are created, and their read range performances and ink consumptions are presented.
- 10 May 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 9, 440-443
Passive UHF Inkjet-Printed Narrow-Line RFID Tags
In this letter, we present a novel radio frequency identification (RFID) tag design optimized especially for the inkjet printing process. These tags are printed using narrow conductors, which enables low cost and fast manufacturing rate. We have manufactured such tag designs using three different line widths: 50, 125, and 200 μm. In this letter, we present the simulation and measurement results. We have also included a comparison between the novel narrow-line tag and a dipole-type commercial tag. Results are encouraging; the read range of the narrow-line tag is comparable to the read range of the commercial tag even though the commercial tag is made of copper, which has approximately two times higher conductivity than the silver ink used in this study. Moreover, the narrow-line tag antenna needs 83% less conductor surface area than the antenna geometry of the commercial tag. This means a significant drop in the manufacturing costs.
- 10 May 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 9, 440-443
Passive UHF Inkjet-Printed Narrow-Line RFID Tags
In this letter, we present a novel radio frequency identification (RFID) tag design optimized especially for the inkjet printing process. These tags are printed using narrow conductors, which enables low cost and fast manufacturing rate. We have manufactured such tag designs using three different line widths: 50, 125, and 200 μm. In this letter, we present the simulation and measurement results. We have also included a comparison between the novel narrow-line tag and a dipole-type commercial tag. Results are encouraging; the read range of the narrow-line tag is comparable to the read range of the commercial tag even though the commercial tag is made of copper, which has approximately two times higher conductivity than the silver ink used in this study. Moreover, the narrow-line tag antenna needs 83% less conductor surface area than the antenna geometry of the commercial tag. This means a significant drop in the manufacturing costs.