Mahmoud Mani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mahmoud Mani has a total of 108 co-authors. Here are the top co-authors by number of shared publications:
M. Kazemi
4 shared publications- Arash Shams Taleghani
Aerospace Research Institute, Ministry of Science, Research and Technology, Tehran, Iran
2 shared publications G.J. Gordon
2 shared publications- Mehran Tadjfar
Turbulence and Multiphase Flow Laboratory, Department of Aerospace Engineering, Amirkabir University of Technology, Tehran, Iran
2 shared publications Mohammad Saeedi
Department of Aerospace Engineering, Amirkabir University of Technology , Tehran, Iran
2 shared publications- Mostafa Kazemi
Aerospace Engineering Department, Amirkabir University of Technology, Tehran, Iran
2 shared publications
Latest Publications
- 6 July 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Experimental study of drag reduction on a simplified road vehicle model using serpentine DBD plasma actuators
This study investigates the aerodynamic drag reduction potential of serpentine dielectric barrier discharge (DBD) plasma actuators applied to a simplified road vehicle model, known as the Ahmed body. Four actuator positions were tested on the rear slant and vertical surfaces using wind tunnel experiments at Reynolds numbers ranging from 1.02 × 10 6 to 1.85 × 10 6 . The actuators operated at 12 kV and 10 kHz, with configurations inspired by earlier optimization studies. The key innovation of this study lies in employing serpentine DBD plasma actuators as a novel flow control device for Ahmed body aerodynamic drag reduction. Results of several experiments show that actuator position UP3, located mid-ramp, yielded the most effective drag reduction up to 36% due to its favorable influence on laminar separation bubble and wake structure. The comparative analysis indicates that serpentine plasma actuators achieve drag-reduction levels comparable to, and in some cases slightly exceeding, previously reported passive and active flow control techniques under similar conditions. The findings support the strategic integration of serpentine DBD actuators in future aerodynamic designs for ground vehicles.
- 6 July 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Experimental study of drag reduction on a simplified road vehicle model using serpentine DBD plasma actuators
This study investigates the aerodynamic drag reduction potential of serpentine dielectric barrier discharge (DBD) plasma actuators applied to a simplified road vehicle model, known as the Ahmed body. Four actuator positions were tested on the rear slant and vertical surfaces using wind tunnel experiments at Reynolds numbers ranging from 1.02 × 10 6 to 1.85 × 10 6 . The actuators operated at 12 kV and 10 kHz, with configurations inspired by earlier optimization studies. The key innovation of this study lies in employing serpentine DBD plasma actuators as a novel flow control device for Ahmed body aerodynamic drag reduction. Results of several experiments show that actuator position UP3, located mid-ramp, yielded the most effective drag reduction up to 36% due to its favorable influence on laminar separation bubble and wake structure. The comparative analysis indicates that serpentine plasma actuators achieve drag-reduction levels comparable to, and in some cases slightly exceeding, previously reported passive and active flow control techniques under similar conditions. The findings support the strategic integration of serpentine DBD actuators in future aerodynamic designs for ground vehicles.
- 8 June 2026
- Published by Springer Nature in Journal of Bionic Engineering
- Vol. 23 (4) , 2323-2346
Aeroacoustics Comparison of Owl, Hawk, and NACA0012 Airfoils Using Microphone Measurements
- 8 June 2026
- Published by Springer Nature in Journal of Bionic Engineering
- Vol. 23 (4) , 2323-2346
Aeroacoustics Comparison of Owl, Hawk, and NACA0012 Airfoils Using Microphone Measurements
- 22 October 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (7) , 9821-9837
Flow Physics of Bio-inspired Airfoils Using Experimental and DES Methods at Reynolds Numbers Below 44 × 103
- 22 October 2025
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 51 (7) , 9821-9837
Flow Physics of Bio-inspired Airfoils Using Experimental and DES Methods at Reynolds Numbers Below 44 × 103
- Open Access
- 2 July 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-19
Owl airfoil aerodynamic noise sources and performance compared to hawk and NACA0012 airfoils for low Reynolds applications
The investigation of low Reynolds number flows is crucial, particularly for applications such as wind turbines and small-scale UAVs. This study compares the owl airfoil with the NACA0012 and hawk airfoils through wind tunnel testing, utilizing pressure sensors and force balance to examine the aerodynamic noise sources and aerodynamic performance of the airfoils. A total of six airfoils were investigated at various Reynolds numbers from 44 × 103 to 160 × 103, considering the glide flight envelop for various owl species. Wind tunnel test results showed higher Cl and L/D ratio for the owl airfoil, outperforming the NACA0012 and hawk airfoils by up to 6.7% and 44.1%, respectively. This is attributed to the optimal camber of the owl airfoil compared to the two other airfoils, and its lower relative thickness too. This helps flight with this airfoil at lower AOA, which reduces noise. In addition, the stall angle for owl airfoil was ranging from 8° to 15° higher than NACA0012 airfoil, which stalled at 10°-11°, and higher than 6° to 12° hawk stall angle. This feature allowed owls to perform efficient flights in glide phase at lower AOA that minimized the main aerodynamic noise sources such as the separations and pressure fluctuations. Pressure measurements represented the initiation of LSB for the owl airfoil at around AOA = 6° to 10° at different Reynolds numbers, while the hawk airfoil shown the presence of LSB starting from AOA = 0°. A detailed analysis of the pressure fluctuations showed that the owl airfoil had fewer sources of aerodynamic noise, such as LSB, stall phenomena, and separated shear layers, on both its upper and lower surfaces, compared to other types of airfoils. Additionally, an analysis in the frequency domain showed that the amplitude of FFT for NACA0012 and hawk airfoil is generally higher compared with the owl airfoil. These findings shed light on the aerodynamic characteristics and noise generation mechanisms of owl airfoil for future research and design considerations.
- 2 July 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-19
Open AccessOwl airfoil aerodynamic noise sources and performance compared to hawk and NACA0012 airfoils for low Reynolds applications
The investigation of low Reynolds number flows is crucial, particularly for applications such as wind turbines and small-scale UAVs. This study compares the owl airfoil with the NACA0012 and hawk airfoils through wind tunnel testing, utilizing pressure sensors and force balance to examine the aerodynamic noise sources and aerodynamic performance of the airfoils. A total of six airfoils were investigated at various Reynolds numbers from 44 × 103 to 160 × 103, considering the glide flight envelop for various owl species. Wind tunnel test results showed higher Cl and L/D ratio for the owl airfoil, outperforming the NACA0012 and hawk airfoils by up to 6.7% and 44.1%, respectively. This is attributed to the optimal camber of the owl airfoil compared to the two other airfoils, and its lower relative thickness too. This helps flight with this airfoil at lower AOA, which reduces noise. In addition, the stall angle for owl airfoil was ranging from 8° to 15° higher than NACA0012 airfoil, which stalled at 10°-11°, and higher than 6° to 12° hawk stall angle. This feature allowed owls to perform efficient flights in glide phase at lower AOA that minimized the main aerodynamic noise sources such as the separations and pressure fluctuations. Pressure measurements represented the initiation of LSB for the owl airfoil at around AOA = 6° to 10° at different Reynolds numbers, while the hawk airfoil shown the presence of LSB starting from AOA = 0°. A detailed analysis of the pressure fluctuations showed that the owl airfoil had fewer sources of aerodynamic noise, such as LSB, stall phenomena, and separated shear layers, on both its upper and lower surfaces, compared to other types of airfoils. Additionally, an analysis in the frequency domain showed that the amplitude of FFT for NACA0012 and hawk airfoil is generally higher compared with the owl airfoil. These findings shed light on the aerodynamic characteristics and noise generation mechanisms of owl airfoil for future research and design considerations.
- 1 November 2024
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 37 (6)
Experimental Study of the Periodic Vortex Shedding and Lock-in Region of an NACA4412 Airfoil
- 1 November 2024
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 37 (6)
Experimental Study of the Periodic Vortex Shedding and Lock-in Region of an NACA4412 Airfoil
- 5 December 2022
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 98, 102-119
Experimental investigation into the flow structure of plasma induced Jet in a 2-D Cross-Flow
- 5 December 2022
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 98, 102-119
Experimental investigation into the flow structure of plasma induced Jet in a 2-D Cross-Flow
- 1 September 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 35 (5) , 05022001
Experimental Investigation of Flow Control on a High-Lift Wing Using Modulated Pulse Jet Vortex Generator
In this paper, the potential of a novel active flow control strategy by means of a modulated pulse jet vortex generator to enhance high-lift performance is demonstrated on a two-dimensional supercritical National Aeronautics and Space Administration (NASA) SC(2)-0714 airfoil with a single slotted trailing-edge flap at a high deflection angle. Fast-switching solenoid valves and compressed air were used as actuators to excite the flow. The vortex generator slot pairs were incorporated into the shoulder of the trailing-edge flap, where the flow separation occurs due to the high flow deflection and severe adverse pressure gradient. In these experiments, in addition to the simple square-wave excitation signal, a burst-modulated excitation signal as a novel pulse jet sequence was implemented to produce the unsteady blowing. The burst-modulation signal was used for the first time for a fast-switching solenoid valve actuator. The experiments were performed at a freestream velocity of with a corresponding Reynolds number of about for a range of angles of attack from 0° to 20° at flap deflection angles from 0° to 35°. The results indicated that the ejection from vortex generator slot pairs was able to prevent flow separation completely in most conditions. These measurements revealed that the burst-modulated excitation was accompanied by more aerodynamic improvements and less air consumption relative to the simple pulsed jet excitation. In the best flow control mode, the results showed about a 12.6% increase in the lift coefficient and a 19.8% decrease in the drag coefficient.- 1 September 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 35 (5) , 05022001
Experimental Investigation of Flow Control on a High-Lift Wing Using Modulated Pulse Jet Vortex Generator
In this paper, the potential of a novel active flow control strategy by means of a modulated pulse jet vortex generator to enhance high-lift performance is demonstrated on a two-dimensional supercritical National Aeronautics and Space Administration (NASA) SC(2)-0714 airfoil with a single slotted trailing-edge flap at a high deflection angle. Fast-switching solenoid valves and compressed air were used as actuators to excite the flow. The vortex generator slot pairs were incorporated into the shoulder of the trailing-edge flap, where the flow separation occurs due to the high flow deflection and severe adverse pressure gradient. In these experiments, in addition to the simple square-wave excitation signal, a burst-modulated excitation signal as a novel pulse jet sequence was implemented to produce the unsteady blowing. The burst-modulation signal was used for the first time for a fast-switching solenoid valve actuator. The experiments were performed at a freestream velocity of with a corresponding Reynolds number of about for a range of angles of attack from 0° to 20° at flap deflection angles from 0° to 35°. The results indicated that the ejection from vortex generator slot pairs was able to prevent flow separation completely in most conditions. These measurements revealed that the burst-modulated excitation was accompanied by more aerodynamic improvements and less air consumption relative to the simple pulsed jet excitation. In the best flow control mode, the results showed about a 12.6% increase in the lift coefficient and a 19.8% decrease in the drag coefficient.- 11 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 237 (4) , 883-898
Experimental investigation of vortex shedding of an airfoil at post-stall incidences
The harmonic vortex shedding from airfoil happens in various incidences. It has noticeable effects on the structure design and aerodynamic performance. In this paper, wind tunnel tests were conducted on a stationary NACA4412 airfoil at angles of attack ranging from [ ] to [ ] and Re number between [ ] and [ ] to examine the vortex shedding frequency and Strouhal number. The wake dynamics at post-stall incidences were investigated by surface pressure, wake flow velocity measurement, and smoke flow visualization. Three phases of the wake dynamics were observed with increasing the incidences beyond the stall: (i) the tiny vortices are shed from the airfoil’s suction side with scattered frequencies, (ii) the shear layer is separated from the LE, rolls up over the airfoil’s suction side and forms the harmonic vortex street, and (iii) the separation point moves from the airfoil’s suction side to the pressure side and leads to the vortex shedding like the bluff bodies. Frequency analysis of aerodynamic loads shows that the flow field’s low-frequency feature has a substantial effect normal to the surface while the vortex street unsteadiness impacts both perpendicular and parallel to the surface. The base pressure coefficient increases suddenly by the vortex street onset in the region (ii) and reaches about 0.4. The universal Strouhal number of 0.18 that is independent of Reynolds number was captured for the angles of attack well beyond the stall. Flow visualization shows that the vortex street establishes longitudinally closer to the airfoil at lower freestream velocity compared to the upper one.
- 11 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 237 (4) , 883-898
Experimental investigation of vortex shedding of an airfoil at post-stall incidences
The harmonic vortex shedding from airfoil happens in various incidences. It has noticeable effects on the structure design and aerodynamic performance. In this paper, wind tunnel tests were conducted on a stationary NACA4412 airfoil at angles of attack ranging from [ ] to [ ] and Re number between [ ] and [ ] to examine the vortex shedding frequency and Strouhal number. The wake dynamics at post-stall incidences were investigated by surface pressure, wake flow velocity measurement, and smoke flow visualization. Three phases of the wake dynamics were observed with increasing the incidences beyond the stall: (i) the tiny vortices are shed from the airfoil’s suction side with scattered frequencies, (ii) the shear layer is separated from the LE, rolls up over the airfoil’s suction side and forms the harmonic vortex street, and (iii) the separation point moves from the airfoil’s suction side to the pressure side and leads to the vortex shedding like the bluff bodies. Frequency analysis of aerodynamic loads shows that the flow field’s low-frequency feature has a substantial effect normal to the surface while the vortex street unsteadiness impacts both perpendicular and parallel to the surface. The base pressure coefficient increases suddenly by the vortex street onset in the region (ii) and reaches about 0.4. The universal Strouhal number of 0.18 that is independent of Reynolds number was captured for the angles of attack well beyond the stall. Flow visualization shows that the vortex street establishes longitudinally closer to the airfoil at lower freestream velocity compared to the upper one.
- 12 April 2022
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 109 (1) , 65-100
Pressure Improvement on a Supercritical High-Lift Wing Using Simple and Modulated Pulse Jet Vortex Generator
- 12 April 2022
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 109 (1) , 65-100
Pressure Improvement on a Supercritical High-Lift Wing Using Simple and Modulated Pulse Jet Vortex Generator
- Open Access
- 1 October 2021
- Published by AIP Publishing in AIP Advances
- Vol. 11 (10) , 105007
Experimental investigation of induced velocity by dielectric barrier discharge plasma actuator in different configurations
This paper aims to study the effect of different geometrical and electrical parameters, including the voltage, frequency, dielectric thickness, gap width between electrodes, length of electrodes, number of electrodes, and shapes of electrodes, on the induced velocity by the Dielectric Barrier Discharge (DBD) plasma actuators in quiescent air. In addition, the effect of the course of induced velocity evolution in the downstream of actuators has been investigated for different geometries. The streamwise velocity was obtained through the total and static pressure measurement using silicon tubes. The model is a flat plate equipped with a DBD plasma actuator. These experiments were performed for the peak-to-peak voltage range between 8 and 15 kV, and two values of frequency are equivalent to 5 and 10 kHz. The results showed that the multilinear DBD plasma actuator has a maximal induced velocity in the same voltage and frequency as of a single DBD plasma actuator. Evaluation of the induced velocity along the streamwise direction for multilinear, serpentine, and horseshoe actuators showed that these actuators had more than one induced velocity peak.
- 1 October 2021
- Published by AIP Publishing in AIP Advances
- Vol. 11 (10) , 105007
Open AccessExperimental investigation of induced velocity by dielectric barrier discharge plasma actuator in different configurations
This paper aims to study the effect of different geometrical and electrical parameters, including the voltage, frequency, dielectric thickness, gap width between electrodes, length of electrodes, number of electrodes, and shapes of electrodes, on the induced velocity by the Dielectric Barrier Discharge (DBD) plasma actuators in quiescent air. In addition, the effect of the course of induced velocity evolution in the downstream of actuators has been investigated for different geometries. The streamwise velocity was obtained through the total and static pressure measurement using silicon tubes. The model is a flat plate equipped with a DBD plasma actuator. These experiments were performed for the peak-to-peak voltage range between 8 and 15 kV, and two values of frequency are equivalent to 5 and 10 kHz. The results showed that the multilinear DBD plasma actuator has a maximal induced velocity in the same voltage and frequency as of a single DBD plasma actuator. Evaluation of the induced velocity along the streamwise direction for multilinear, serpentine, and horseshoe actuators showed that these actuators had more than one induced velocity peak.