SMSiyamak Moradi

Siyamak Moradi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Siyamak Moradi has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Synthesis, Characterization, and Assessment of a CeO2@Nanoclay Nanocomposite for Enhanced Oil Recovery

    by Mohammad Javad Nazarahari, Abbas Khaksar Manshad, Siyamak Moradi, Ali Shafiei, Jagar Abdulazez Ali, S. Mohammad Sajadi, Alireza Keshavarz

    In this paper, synthesis and characterization of a novel CeO2/nanoclay nanocomposite (NC) and its effects on IFT reduction and wettability alteration is reported in the literature for the first time. The NC was characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), energy-dispersive X-ray spectroscopy (EDS), and EDS MAP. The surface morphology, crystalline phases, and functional groups of the novel NC were investigated. Nanofluids with different concentrations of 100, 250, 500, 1000, 1500, and 2000 ppm were prepared and used as dispersants in porous media. The stability, pH, conductivity, IFT, and wettability alternation characteristics of the prepared nanofluids were examined to find out the optimum concentration for the selected carbonate and sandstone reservoir rocks. Conductivity and zeta potential measurements showed that a nanofluid with concentration of 500 ppm can reduce the IFT from 35 mN/m to 17 mN/m (48.5% reduction) and alter the contact angle of the tested carbonate and sandstone reservoir rock samples from 139° to 53° (38% improvement in wettability alteration) and 123° to 90° (27% improvement in wettability alteration), respectively. A cubic fluorite structure was identified for CeO2 using the standard XRD data. FESEM revealed that the surface morphology of the NC has a layer sheet morphology of CeO2/SiO2 nanocomposite and the particle sizes are approximately 20 to 26 nm. TGA analysis results shows that the novel NC has a high stability at 90 °C which is a typical upper bound temperature in petroleum reservoirs. Zeta potential peaks at concentration of 500 ppm which is a sign of stabilty of the nanofluid. The results of this study can be used in design of optimum yet effective EOR schemes for both carbobate and sandstone petroleum reservoirs.


  • Open Access

    Application of Natural Surfactants for Enhanced Oil Recovery – Critical Review

    by Zahra Bachari, Ali Akbar Isari, Hosein Mahmoudi, Siyamak Moradi, Elaheh Hamed Mahvelati

    The huge worldwide energy demand, and the need for more crude oil production, together with the low-efficiency of the conventional abstraction methods are part of the reasons for increasing interest in Enhanced Oil Recovery (EOR) techniques for recovering more oil from existing reservoirs. Utilization of different types of surfactants (synthetic or natural) in order to decrease the water-oil interfacial tension (IFT) is one of the most common methods for EOR. However, polymers and synthetic chemicals have a number of disadvantages such as linking to fossil fuels, high cost and environmental impacts. In this review, the application of natural surfactants produced from the leaves of Olive, Spistan, Prosopis, Mulberry, Zizyphus spina Christi, Soapnut and Chamomilla plants in EOR processes are investigated. The effects of natural surfactants extracted from the leaves of the mentioned plants on reduction of the oil-water interfacial tension (IFT) are studied and compared extensively. Pendant drop and ring methods have been employed by most of researchers to identify the IFT values as a determining parameter in performance of natural surfactant flooding to increase ultimate oil recovery. This comparative study in the application of natural surfactants in EOR will pave the way for future studies and helps further research in EOR schemes.


  • Open Access

    Determination of Effective Parameters of Gas Injection in Naturally Fractured Reservoirs by Combination of Reservoir Simulation and Design of Experiment Techniques

    by Behdad Parnian Khoy, Siyamak Moradi, Ghasem Zargar, Mostafa Ganjeh Ghazvini, Elaheh Hamed Mahvelati

    Screening analysis is a useful guideline which helps us with proper field selection for different enhanced oil recovery processes. In this work, reservoir simulation is combined with experimental design to estimate main effects and possible interactions of reservoir rock and fluid properties on performance of different gas injection processes in naturally fractured reservoirs (NFRs). Studied parameters include reservoir thickness (h), oil viscosity μo), pore size distribution (λ), horizontal permeability (Kh), storage capacity (ω), reservoir dip, critical water saturation (Swc) and threshold capillary pressure (pct). The recovery factors of different simulation designs are analyzed by use of fractional factorial design (FFD) approach. Finally, the statistical significance of results are evaluated by hypothesis testing and ANOVA, and presented by Pareto and tornado plots. Main effect analysis showed that effective parameters are ordered with respect to their importance as follows: For Methane and nitrogen injection: Kh, dip, Swc, ω, h, μo and λ; threshold capillary pressure showed a minor effect on recovery factor. For Carbon dioxide injection: μo, dip, Swc, ω, h and Kh; Pore size distribution (λ) and threshold pressure were not shown to be statistically significant in this process. Likeness of main effects and parameter interactions for methane and nitrogen injection prove the similarity of dominant mechanisms and characteristics of these processes compared to CO2 injection which seems almost different.


  • Drilling fluid loss control via implementing the FMI and DSI logs to protect environment

    by Mohammad Shalafi, Siyamak Moradi, Mohammad Kamal GhassemAlaskari, Malihe Sadat Kazemi


  • Open Access

    Determination of Shale Volume and Distribution Patterns and Effective Porosity from Well Log Data Based On Cross-Plot Approach for A Shaly Carbonate Gas Reservoir

    by Siyamak Moradi, Mohammad Moeini, Mohammad Kamal Ghassem Al-Askari, Elaheh Hamed Mahvelati

    Determination of shale volume distribution is one of the most important factors that has to be considered in formation evaluation, since existence of shale reduces effective porosity and permeability of the reservoir. In this paper, shale volume and distribution (dispersed, laminar and structural) and formation effective porosity are estimated from well log data and cross-plots. Results show that distribution of shale is mainly dispersed with few of laminar ones, and the quality of reservoir (effective porosity) decreases with depth resulting in low productivity of gas wells drilled in lower zones. Good agreement of estimated shale volumes and effective porosities from neutron-density cross-plot with the values determined from gamma ray log (CGR) and core analysis demonstrates the accuracy and applicability of these plots in determination of petrophysical parameters from conventional log data.


  • Flow prediction using well log data and intelligent techniques

    by M. Hassanpoor, S. Moradi, M. K. Ghassem Alaskari, S. Parchekhari

    Spatial distribution of petrophysical properties within the reservoirs is important to provide a reliable reservoir model. The most complete reservoir description is generally provided through the identification of flow units. Then, the constructed model can be used for reservoir simulation of different production scenarios within the reservoir. However, before performing modeling and simulation jobs, accurate prediction of flow units is an important task and to reach a reliable petrophysical description first of all one should be able to predict flow units with high precision. Achieving this goal will be discussed in this article. This paper suggests intelligent techniques using artificial neural network (ANN), fuzzy logic (FL), and neuro-fuzzy (NF) to determine flow units from well log data. For this purpose, available routine core and wireline log data from five wells in Ilam Formation at the Ahwaz super giant oil field are used to find the best intelligent formulation between core-derived flow units and well log data. Validation of the predictive capability of the models was evaluated in one separate cored well (blind test well). The results show that FL-derived flow units had better accuracy with respect to other techniques. This comparison showed that FL can be used as the most reliable intelligent technique for flow unit prediction from well log data in uncored wells.

  • Open Access

    Separating Well Log Data to Train Support Vector Machines for Lithology Prediction in a Heterogeneous Carbonate Reservoir

    by Mohammad Ali Sebtosheikh, Reza Motafakkerfard, Mohammad Ali Riahi, Siyamak Moradi


  • Open Access

    A Novel Combinatorial Approach to Discrete Fracture Network Modeling in Heterogeneous Media

    by Saeed Balouchi, Siyamak Moradi, Mohsen Masihi, Ali Erfaninia

  • Open Access

    Investigation of asphaltene precipitation in miscible gas injection processes: experimental study and modeling

    by S. Moradi, M. Dabiri, B. Dabir, D. Rashtchian, M. A. Emadi

    Asphaltene precipitation during natural depletion and miscible gas injection is a common problem in oilfields throughout the world. In this work, static precipitation tests are conducted to investigate the effects of pressure, temperature and gas type and concentration on asphaltene instability. Three different oil samples have been studied under reservoir conditions with/without nitrogen and methane injection. Besides applying common thermodynamic models, a new scaling equation is presented to predict asphaltene precipitation under HPHT gas injection. Extensive published data from the literature are also used in model development. The scaling approach is attractive because it is simple and complex asphaltene properties are not involved in the calculations. Moreover, the proposed model provides universal parameters for different fluid samples over a wide range of pressure and temperature that makes it novel for evaluation of future gas injection projects when simple PVT data are available.