Cha Chee Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Cha Chee Sun has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Ah Heng You
Multimedia Univ, Fac Engn & Technol, Jalan Ayer Keroh Lama, Melaka 75450, Malaysia
2 shared publicationsLay Lian Teo
Multimedia Univ, Fac Informat Sci & Technol, Jalan Ayer Keroh Lama, Melaka 75450, Malaysia
2 shared publicationsA. H. You
Faculty of Engineering and Technology, Multimedia University, Jalan Ayer Keroh Lama, 75450 Melaka, Malaysia
1 shared publicationA.H. You
Faculty of Engineering and Technology, Multimedia University, Jalan Ayer Keroh Lama, 75450 Melaka, Malaysia
1 shared publication- Eng Kiong Wong
Faculty of Engineering and Technology, Multimedia University
1 shared publication L. L. Teo
Faculty of Engineering and Technology, Multimedia University, Jalan Ayer Keroh Lama, 75450 Melaka, Malaysia
1 shared publication
Latest Publications
- 3 November 2022
- Published by International Journal of Technology in International Journal of Technology
- Vol. 13 (6) , 1336-1343
XRD Measurement for Particle Size Analysis of PMMA Polymer Electrolytes with SiO2
PMMA-based polymer electrolytes with LiCF3SO3 lithium salt, EC plasticizer, and SiO2 filler are prepared using the solution cast method. SiO2 filler sizes at 10 ?m and 63 ?m are used to estimate the particle size in the polymer electrolytes system. EIS analysis calculates ionic conductivity based on the Cole-Cole plot generated in frequency ranging from 0.1 Hz to 1 MHz. The calculation results in ionic conductivity at 1.44 × 10-4 S/cm and 8.1 × 10-5 S/cm for 10 ?m and 63 ?m SiO2 filler, respectively. FWHM measurement is performed for each diffraction peak based on the XRD spectra. Debye-Scherrer equation is used to estimate the resultant particle size. Peak broadening effect caused by the instrument is considered for a more accurate estimation of particle size in the polymer electrolyte system. Linear regression is employed to determine the average particle size arising from these diffraction peaks. The results showed that larger filler size results in the formation of a larger particle size.
- 3 November 2022
- Published by International Journal of Technology in International Journal of Technology
- Vol. 13 (6) , 1336-1343
XRD Measurement for Particle Size Analysis of PMMA Polymer Electrolytes with SiO2
PMMA-based polymer electrolytes with LiCF3SO3 lithium salt, EC plasticizer, and SiO2 filler are prepared using the solution cast method. SiO2 filler sizes at 10 ?m and 63 ?m are used to estimate the particle size in the polymer electrolytes system. EIS analysis calculates ionic conductivity based on the Cole-Cole plot generated in frequency ranging from 0.1 Hz to 1 MHz. The calculation results in ionic conductivity at 1.44 × 10-4 S/cm and 8.1 × 10-5 S/cm for 10 ?m and 63 ?m SiO2 filler, respectively. FWHM measurement is performed for each diffraction peak based on the XRD spectra. Debye-Scherrer equation is used to estimate the resultant particle size. Peak broadening effect caused by the instrument is considered for a more accurate estimation of particle size in the polymer electrolyte system. Linear regression is employed to determine the average particle size arising from these diffraction peaks. The results showed that larger filler size results in the formation of a larger particle size.
- 22 June 2019
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 39 (7) , 612-619
Characterizations of PMMA-based polymer electrolyte membranes with Al2O3
Poly(methyl methacrylate) (PMMA)-based polymer electrolyte membranes are prepared through the solution cast method, with PMMA:ethylene carbonate (EC):LiCF3SO3:Al2O3 weight ratio of 55.13:18.34:24.5:2. The effect of Al2O3 filler grain sizes of 50 nm and 10 μm on the polymer electrolytes was studied in this work. From the Cole-Cole plot obtained through electrochemical impedance spectroscopy, the highest ionic conductivity for 50-nm Al2O3 in the PMMA-LiCF3SO3-EC-Al2O3 sample was measured as 1.52 × 10−4 S/cm at room temperature. The bonding formation among the host polymer and other additives in the polymer electrolytes has been studied using Fourier transform infrared spectroscopy. A strong occurrence of CH3 stretching mode has proven that nano size Al2O3 results in a much stronger bonding effect with the host polymer. The particle sizes were calculated by applying the Debye-Scherrer equation from the X-ray diffraction results. This work considers the effect of instrument broadening to further improve the accuracy of particle broadening for particle size calculation. The average particle size of nano size Al2O3 in the PMMA sample is calculated as 2.9693 nm. Moreover, a higher amorphousity level obtained from nano size filler polymer electrolyte of 98.5% computed from differential scanning calorimetry thermograms had also explained the achievement of high ionic conductivity in this work.
- 22 June 2019
- Published by Walter de Gruyter GmbH in Journal of Polymer Engineering
- Vol. 39 (7) , 612-619
Characterizations of PMMA-based polymer electrolyte membranes with Al2O3
Poly(methyl methacrylate) (PMMA)-based polymer electrolyte membranes are prepared through the solution cast method, with PMMA:ethylene carbonate (EC):LiCF3SO3:Al2O3 weight ratio of 55.13:18.34:24.5:2. The effect of Al2O3 filler grain sizes of 50 nm and 10 μm on the polymer electrolytes was studied in this work. From the Cole-Cole plot obtained through electrochemical impedance spectroscopy, the highest ionic conductivity for 50-nm Al2O3 in the PMMA-LiCF3SO3-EC-Al2O3 sample was measured as 1.52 × 10−4 S/cm at room temperature. The bonding formation among the host polymer and other additives in the polymer electrolytes has been studied using Fourier transform infrared spectroscopy. A strong occurrence of CH3 stretching mode has proven that nano size Al2O3 results in a much stronger bonding effect with the host polymer. The particle sizes were calculated by applying the Debye-Scherrer equation from the X-ray diffraction results. This work considers the effect of instrument broadening to further improve the accuracy of particle broadening for particle size calculation. The average particle size of nano size Al2O3 in the PMMA sample is calculated as 2.9693 nm. Moreover, a higher amorphousity level obtained from nano size filler polymer electrolyte of 98.5% computed from differential scanning calorimetry thermograms had also explained the achievement of high ionic conductivity in this work.
- 9 May 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1963 (1) , 020028
Effect of Al2O3 in poly(methyl methacrylate) composite polymer electrolytes
In this work, the effect of inert fillers on poly(methyl methacrylate) (PMMA) composite polymer electrolytes (CPEs) are investigated. The PMMA–LiCF3SO3–EC–Al2O3 composite polymer electrolytes were prepared using solution casting method at room temperature. Lithium trifluoromethanesulfonate (LiCF3SO3) is used as the electrolyte salt which plays an important role in Li ion transfer. In order to soften the polymer matrix, ethylene carbonate (EC) is introduced into the CPEs to help in the disassociation of lithium salt ion pairs. Nano sized aluminium oxide (Al2O3) is then incorporated to enhance mechanical strength and ionic conductivity of the polymer electrolyte. The optimum of 2 wt.% 50 nm Al2O3 was added into the PMMA polymer electrolyte sample. Through Electrochemical Impedance Spectroscopy (EIS) measurements, the highest ionic conductivity at room temperature is determined as 1.52×10-4 S/cm. FTIR spectra analysis showed CH2 twisting mode at 1383.43 cm−1, C=O stretching mode at 1721.56 cm-1 which proven the interaction between host polymer and lithium salt and CH3 stretching mode at 2981.34 cm-1. XRD analysis had also been performed to study the structural behaviour of the PMMA polymer electrolyte. The intense peak at position 2θ angle of 15.04°, 30.92° and 45.58° occur upon interaction with Al2O3. Lastly, the surface morphology is studied through SEM+EDX analysis.
- 9 May 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1963 (1) , 020028
Effect of Al2O3 in poly(methyl methacrylate) composite polymer electrolytes
In this work, the effect of inert fillers on poly(methyl methacrylate) (PMMA) composite polymer electrolytes (CPEs) are investigated. The PMMA–LiCF3SO3–EC–Al2O3 composite polymer electrolytes were prepared using solution casting method at room temperature. Lithium trifluoromethanesulfonate (LiCF3SO3) is used as the electrolyte salt which plays an important role in Li ion transfer. In order to soften the polymer matrix, ethylene carbonate (EC) is introduced into the CPEs to help in the disassociation of lithium salt ion pairs. Nano sized aluminium oxide (Al2O3) is then incorporated to enhance mechanical strength and ionic conductivity of the polymer electrolyte. The optimum of 2 wt.% 50 nm Al2O3 was added into the PMMA polymer electrolyte sample. Through Electrochemical Impedance Spectroscopy (EIS) measurements, the highest ionic conductivity at room temperature is determined as 1.52×10-4 S/cm. FTIR spectra analysis showed CH2 twisting mode at 1383.43 cm−1, C=O stretching mode at 1721.56 cm-1 which proven the interaction between host polymer and lithium salt and CH3 stretching mode at 2981.34 cm-1. XRD analysis had also been performed to study the structural behaviour of the PMMA polymer electrolyte. The intense peak at position 2θ angle of 15.04°, 30.92° and 45.58° occur upon interaction with Al2O3. Lastly, the surface morphology is studied through SEM+EDX analysis.
- 23 October 2012
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 60 (1) , 10204
Impact ionization coefficients of 4H- and 6H-SiC
The Monte Carlo (MC) simulation of electron and hole impact ionization rates for 4H- and 6H-SiC in high electric field is presented. This work focuses on the study of impact ionization rates and impact ionization coefficients since these parameters play a very important role in determining the device performance. In our simulation, the impact ionization rates are obtained by using modified Keldysh equation with a softness factor fitted to the experimental data described by other researchers. The electron and hole impact ionization coefficients in 4H- and 6H-SiC are parameterized at high electric field. The electron and hole impact ionization coefficients for a wide range of electric fields have been successfully derived in our model.
- 23 October 2012
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 60 (1) , 10204
Impact ionization coefficients of 4H- and 6H-SiC
The Monte Carlo (MC) simulation of electron and hole impact ionization rates for 4H- and 6H-SiC in high electric field is presented. This work focuses on the study of impact ionization rates and impact ionization coefficients since these parameters play a very important role in determining the device performance. In our simulation, the impact ionization rates are obtained by using modified Keldysh equation with a softness factor fitted to the experimental data described by other researchers. The electron and hole impact ionization coefficients in 4H- and 6H-SiC are parameterized at high electric field. The electron and hole impact ionization coefficients for a wide range of electric fields have been successfully derived in our model.