Arbi Dimyati
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Arbi Dimyati has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Joachim Mayer
Forschungszentrum Jülich GmbH
2 shared publications - Fu-Chuan Hsu
Metal Industries Research and Development Centre (MIRDC), Kaohsiung 81160, Taiwan
1 shared publication - Hwa-Teng Lee
Department of Mechanical Engineering, National Cheng Kung University, Tainan 70101, Taiwan
1 shared publication - Mohammad Dani1 shared publication
Parikin Parikin
1 shared publicationPudji Untoro
1 shared publication
Latest Publications
- 30 August 2015
- Published by Universitas Indonesia in Makara Journal of Technology
- Vol. 19 (2) , 85
Transmission Electron Microscopy Characterization of High-Temperatur Oxidation of Fe-20Cr-5Al Alloy Prepared by Focused Ion Beam Technique
The Focused Ion Beam (FIB) technique was applied for cross section preparation of the oxidized alloy for Transmission Electron Microscopy (TEM) study. Prior to preparation, the specimens of Fe-20Cr-5Al alloy sheet were oxidized in air at 1200 oC for 2 minutes, 10 minutes, 2 hours, and 100 hours. The microstructure and elemental composition of the samples were characterized using TEM equipped with an Energy Dispersive X-Ray Spectroscopy (EDX). The Electron Energy Loss Spectroscopy (EELS) was used to determine of the light elements. The TEM investigation reveals remarkable microstructure evolution of the specimens during oxidation which generally exhibit a typical multi-layer structure. The TEM images, however, can provide detailed description about the phases occur after oxidation such as the Tungsten (W) and the Gallium (Ga) layers on top of the samples obviously formed during FIB preparation, the formation of Al2O3 and Cr2O3 layer, MgAl2O4 spinel, porosity, Zr/Hf/Mg phases or clusters inside the oxide scale. Hence, the FIB technique has been proven to be reliable preparation technique for microstructural and elemental studies of Fe-20Cr-5Al alloy using TEM. Published at: Vol 19, No 2 (2015) pages: 85-89 DOI: a=document.forms['pub'].pubId.value; b=document.forms['pub'].articleId.value; ar=a.split('.'); if(ar[ar.length-1]==b){ document.forms['pub'].show.value=a; }else{ front=a.substring(0,a.lastIndexOf('.')+1); front=front.replace('mjt','mst'); document.forms['pub'].show.value=front+b; } Full PDF Download
- 30 August 2015
- Published by Universitas Indonesia in Makara Journal of Technology
- Vol. 19 (2) , 85
Transmission Electron Microscopy Characterization of High-Temperatur Oxidation of Fe-20Cr-5Al Alloy Prepared by Focused Ion Beam Technique
The Focused Ion Beam (FIB) technique was applied for cross section preparation of the oxidized alloy for Transmission Electron Microscopy (TEM) study. Prior to preparation, the specimens of Fe-20Cr-5Al alloy sheet were oxidized in air at 1200 oC for 2 minutes, 10 minutes, 2 hours, and 100 hours. The microstructure and elemental composition of the samples were characterized using TEM equipped with an Energy Dispersive X-Ray Spectroscopy (EDX). The Electron Energy Loss Spectroscopy (EELS) was used to determine of the light elements. The TEM investigation reveals remarkable microstructure evolution of the specimens during oxidation which generally exhibit a typical multi-layer structure. The TEM images, however, can provide detailed description about the phases occur after oxidation such as the Tungsten (W) and the Gallium (Ga) layers on top of the samples obviously formed during FIB preparation, the formation of Al2O3 and Cr2O3 layer, MgAl2O4 spinel, porosity, Zr/Hf/Mg phases or clusters inside the oxide scale. Hence, the FIB technique has been proven to be reliable preparation technique for microstructural and elemental studies of Fe-20Cr-5Al alloy using TEM. Published at: Vol 19, No 2 (2015) pages: 85-89 DOI: a=document.forms['pub'].pubId.value; b=document.forms['pub'].articleId.value; ar=a.split('.'); if(ar[ar.length-1]==b){ document.forms['pub'].show.value=a; }else{ front=a.substring(0,a.lastIndexOf('.')+1); front=front.replace('mjt','mst'); document.forms['pub'].show.value=front+b; } Full PDF Download
- 5 March 2006
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 128 (3) , 468-475
Application of EDM Hole-Drilling Method to the Measurement of Residual Stress in Tool and Carbon Steels
This study adopts the application of the electrodischarge machining (EDM) hole-drilling method to the measurement of residual stress in AISI D2 cold work tool steel, AISI H13 hot work tool steel, and AISI 1045 medium carbon steel. A calibration procedure based on the thermal conductivity of the material is conducted to compensate for the additional compressive stress induced in the workpiece by the EDM hole-drilling operation. Since the formation of this white layer influences the magnitude of the induced stress, the scanning electron microscopy, transmission electron microscopy, and nanoindentation techniques are used to examine the microstructure and hardness of the white layer resolidified on the EDMed surface. The experimental results reveal that combination of the hole-drilling strain-gage method (ASTM standard E837) with an EDM drilling process provides the effective means of determining the residual stress in materials with high hardness and good wear resistance.
- 5 March 2006
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 128 (3) , 468-475
Application of EDM Hole-Drilling Method to the Measurement of Residual Stress in Tool and Carbon Steels
This study adopts the application of the electrodischarge machining (EDM) hole-drilling method to the measurement of residual stress in AISI D2 cold work tool steel, AISI H13 hot work tool steel, and AISI 1045 medium carbon steel. A calibration procedure based on the thermal conductivity of the material is conducted to compensate for the additional compressive stress induced in the workpiece by the EDM hole-drilling operation. Since the formation of this white layer influences the magnitude of the induced stress, the scanning electron microscopy, transmission electron microscopy, and nanoindentation techniques are used to examine the microstructure and hardness of the white layer resolidified on the EDMed surface. The experimental results reveal that combination of the hole-drilling strain-gage method (ASTM standard E837) with an EDM drilling process provides the effective means of determining the residual stress in materials with high hardness and good wear resistance.