Luc Laperrie`rE
Research Subjects
Luc Laperrie`rE has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Alain Desrochers
Department of Mechanical Engineering, Université de Sherbrooke, Sherbrooke, QC J1K 2R1, Canada
2 shared publications - Walid Ghie
Universite´ de Sherbrooke, Department of Mechanical Engineering
2 shared publications - Alain Desrochers
Universite´ de Sherbrooke, Department of Mechanical Engineering
1 shared publication - W. Ghie
Université du Québec à Trois-Rivières
1 shared publication
Latest Publications
- 18 May 2007
- Published by Springer Nature
- p. 95-104
Re-Design of Mechanical Assemblies using the Unified Jacobian-Torsor Model for Tolerance Analysis
- 18 May 2007
- Published by Springer Nature
- p. 95-104
Re-Design of Mechanical Assemblies using the Unified Jacobian-Torsor Model for Tolerance Analysis
- 1 July 2006
- Published by Springer Nature
- p. 473-485
Predicting Design Quality through Sensitivity Modeling
- 1 July 2006
- Published by Springer Nature
- p. 473-485
Predicting Design Quality through Sensitivity Modeling
- 1 March 2003
- Published by Wiley in Journal of Computing and Information Science in Engineering
- Vol. 3 (1) , 2-14
Application of a Unified Jacobian—Torsor Model for Tolerance Analysis
Because of uncertainties in manufacturing processes, a mechanical part always shows variations in its geometrical characteristics (ex. form, dimension, orientation and position). Quality then often reflect how well tolerances and hence, functional requirements, are being achieved by the manufacturing processes in the final product. From a design perspective, efficient methods must be made available to compute, from the tolerances on individual parts, the value of the functional requirement on the final assembly. This is known as tolerance analysis. To that end, existing methods, often based on modeling of the open kinematic chains in robotics, are classified as deterministic or statistical. These methods suppose that the assembled parts are not perfect with regard to the nominal geometry and are rigid. The rigidity of the parts implies that the places of contacts are regarded as points. The validation or the determination of a tolerance zone is therefore accomplished by a series of simulation in specific points subjected to assembly constraints. To overcome the limitations and difficulties of point based approaches, the paper proposes the unification of two existing models: the Jacobian’s matrix model, based on the infinitesimal modeling of open kinematic chains in robotics, and the tolerance zone representation model, using small displacement screws and constraints to establish the extreme limits between which points and surfaces can vary. The approach also uses interval algebra as a novel method to take tolerance boundaries into account in tolerance analysis. The approach has been illustrated on a simple two parts assembly, nevertheless demonstrating the capability of the method to handle three-dimensional geometry. The results are then validated geometrically, showing the overall soundness of the approach.
- 1 March 2003
- Published by Wiley in Journal of Computing and Information Science in Engineering
- Vol. 3 (1) , 2-14
Application of a Unified Jacobian—Torsor Model for Tolerance Analysis
Because of uncertainties in manufacturing processes, a mechanical part always shows variations in its geometrical characteristics (ex. form, dimension, orientation and position). Quality then often reflect how well tolerances and hence, functional requirements, are being achieved by the manufacturing processes in the final product. From a design perspective, efficient methods must be made available to compute, from the tolerances on individual parts, the value of the functional requirement on the final assembly. This is known as tolerance analysis. To that end, existing methods, often based on modeling of the open kinematic chains in robotics, are classified as deterministic or statistical. These methods suppose that the assembled parts are not perfect with regard to the nominal geometry and are rigid. The rigidity of the parts implies that the places of contacts are regarded as points. The validation or the determination of a tolerance zone is therefore accomplished by a series of simulation in specific points subjected to assembly constraints. To overcome the limitations and difficulties of point based approaches, the paper proposes the unification of two existing models: the Jacobian’s matrix model, based on the infinitesimal modeling of open kinematic chains in robotics, and the tolerance zone representation model, using small displacement screws and constraints to establish the extreme limits between which points and surfaces can vary. The approach also uses interval algebra as a novel method to take tolerance boundaries into account in tolerance analysis. The approach has been illustrated on a simple two parts assembly, nevertheless demonstrating the capability of the method to handle three-dimensional geometry. The results are then validated geometrically, showing the overall soundness of the approach.