Pär G. Jönsson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pär G. Jönsson has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Andrey Karasev
Material Science and Engineering, KTH Royal Institute of Technology, SE-100 44 Stockholm, Sweden
2 shared publications A. Karasev
Department of Materials Science and Engineering, Royal Institute of Technology (KTH), SE-100 44 Stockholm, Sweden
1 shared publication- Anders Tilliander
Division of Processes, Department of Material Science and Engineering, KTH Royal Institute of Technology, SE-100 44 Stockholm, Sweden
1 shared publication Arashk Memarpour
Höganäs AB Global Process Development; Höganäs 26383 Sweden
1 shared publication- Diana Janis
KTH Royal Institute of Technology; Stockholm 100 44 Sweden
1 shared publication - Hamid Doostmohammadi
Shahid Bahonar University of Kerman
1 shared publication
Latest Publications
- 7 April 2016
- Published by Wiley in Steel Research International
- Vol. 87 (11) , 1461-1468
Evolution of Non-Metallic Inclusions from FeTi70R Alloys during Alloying of Fe-40Ni-20Cr Steels
- 7 April 2016
- Published by Wiley in Steel Research International
- Vol. 87 (11) , 1461-1468
Evolution of Non-Metallic Inclusions from FeTi70R Alloys during Alloying of Fe-40Ni-20Cr Steels
- 12 February 2015
- Published by Wiley in Steel Research International
- Vol. 86 (11) , 1271-1278
A Study of Cluster Characteristics in Liquid Stainless Steel and in a Clogged Nozzle
- 12 February 2015
- Published by Wiley in Steel Research International
- Vol. 86 (11) , 1271-1278
A Study of Cluster Characteristics in Liquid Stainless Steel and in a Clogged Nozzle
- 4 September 2012
- Published by Wiley in Steel Research International
- Vol. 84 (2) , 169-177
Investigating the Effect of Slag on Decarburization in an AOD Converter Using a Fundamental Model
- 4 September 2012
- Published by Wiley in Steel Research International
- Vol. 84 (2) , 169-177
Investigating the Effect of Slag on Decarburization in an AOD Converter Using a Fundamental Model
- 18 May 2010
- Published by Wiley in Steel Research International
- Vol. 81 (5) , 398-406
A Comparison of a Two‐Dimensional and a Three‐Dimensional Method for Inclusion Determinations in Tool Steel
To produce clean commercial tool steel the non‐metallic inclusions characteristics have to be known, since they influence the mechanical properties of steel. In this work, inclusion characteristics in steel samples from plant trials were studied. The samples were collected in the steel plant according the two following methods: (a) 2D investigations of inclusions by a cross sectional method and (b) 3D investigations of inclusions collected on a film filter after electrolytic extraction. More specifically, the chemical composition, morphology, number and size distribution of inclusions in tool steel samples taken from ladle during melt treatment were determined by both methods. In both methods SEM equipped with EDS was used for compositional analysis of inclusions. In addition, in the cross sectional method an automated detection program called ‘INCAFeature’ was used to collect more statistics of non‐metallic inclusions. The composition of inclusions larger than 5 µm was found to contain 49% CaO based on the results from both methods. However, for smaller inclusions it was found that the accuracy of the 2D method was less than that of the 3D method due to the influence of the metal matrix on the results. In addition, it was found that a critical inclusion size of 4 µm could be defined for the 3D method, above which the standard deviation in composition determination was very low.
- 18 May 2010
- Published by Wiley in Steel Research International
- Vol. 81 (5) , 398-406
A Comparison of a Two‐Dimensional and a Three‐Dimensional Method for Inclusion Determinations in Tool Steel
To produce clean commercial tool steel the non‐metallic inclusions characteristics have to be known, since they influence the mechanical properties of steel. In this work, inclusion characteristics in steel samples from plant trials were studied. The samples were collected in the steel plant according the two following methods: (a) 2D investigations of inclusions by a cross sectional method and (b) 3D investigations of inclusions collected on a film filter after electrolytic extraction. More specifically, the chemical composition, morphology, number and size distribution of inclusions in tool steel samples taken from ladle during melt treatment were determined by both methods. In both methods SEM equipped with EDS was used for compositional analysis of inclusions. In addition, in the cross sectional method an automated detection program called ‘INCAFeature’ was used to collect more statistics of non‐metallic inclusions. The composition of inclusions larger than 5 µm was found to contain 49% CaO based on the results from both methods. However, for smaller inclusions it was found that the accuracy of the 2D method was less than that of the 3D method due to the influence of the metal matrix on the results. In addition, it was found that a critical inclusion size of 4 µm could be defined for the 3D method, above which the standard deviation in composition determination was very low.
- 7 February 2005
- Published by Wiley in Scandinavian Journal of Metallurgy
- Vol. 34 (1) , 41-56
Process model of inclusion separation in a stirred steel ladle
A mathematical model, which can be used as a process model in production, was developed to predict total oxygen content and size distribution of non‐metallic inclusions in an agitated steel melt. Using a given pre‐deoxidation total‐oxygen‐content value and calculated velocity and turbulence data (induction or gas stirring), model output can be generated as a function of stirring time. Predicted initial inclusion size distributions were in good agreement with inclusion size distributions quantitatively determined by light optical microscopy and classification according to the Swedish standard SS 11 11 16. Results from simulations carried out for the two types of stirring indicated that the model can predict total oxygen content and inclusion size distribution as a function of time for induction and gas stirring in an acceptable way.
- 7 February 2005
- Published by Wiley in Scandinavian Journal of Metallurgy
- Vol. 34 (1) , 41-56
Process model of inclusion separation in a stirred steel ladle
A mathematical model, which can be used as a process model in production, was developed to predict total oxygen content and size distribution of non‐metallic inclusions in an agitated steel melt. Using a given pre‐deoxidation total‐oxygen‐content value and calculated velocity and turbulence data (induction or gas stirring), model output can be generated as a function of stirring time. Predicted initial inclusion size distributions were in good agreement with inclusion size distributions quantitatively determined by light optical microscopy and classification according to the Swedish standard SS 11 11 16. Results from simulations carried out for the two types of stirring indicated that the model can predict total oxygen content and inclusion size distribution as a function of time for induction and gas stirring in an acceptable way.