Hans Jakob Schindler
Research Subjects
Hans Jakob Schindler has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Boris Semenov
St . Petersburg University
1 shared publication- Christian Leinenbach
Swiss Federal Laboratories for Materials Science and Technology, Dübendorf, Switzerland
1 shared publication H. J. Martens
Sulzer Innotec AG, Winterthur, Switzerland
1 shared publicationP. Bertschinger
Mat-Tec SA
1 shared publicationPeter Bertschinger
St . Petersburg University
1 shared publicationS. Sönnichsen
Wärtsilä Schweiz AG, Winterthur, Switzerland
1 shared publication
Latest Publications
- Open Access
- 1 January 2017
- Published by Elsevier in Procedia Structural Integrity
- Vol. 7, 383-390
An analytical approach to quantify the effect of the R-ratio on da/dN in the Paris regime
- 1 January 2017
- Published by Elsevier in Procedia Structural Integrity
- Vol. 7, 383-390
Open AccessAn analytical approach to quantify the effect of the R-ratio on da/dN in the Paris regime
- 12 January 2010
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 636-637, 1490-1495
Fracture Behaviour of Brazed Soft Martensitic Stainless Steel Joints under Cyclic Loading
The fracture behaviour of brazed joints of the soft martensitic stainless steel X3CrNiMo13-4 under cyclic loading is investigated. The fatigue crack propagation curves (da/dN-ΔK) were derived for different load ratios R. The fatigue crack threshold values ΔKth were estimated to be 9 MPa m0.5, 7 MPa m0.5, 6 MPa m0.5 and 4 MPa m0.5 for the R values of 0.1, 0.3, 0.5 and 0.7, respectively. In addition, crack growth curves were derived for different constant loads ΔF. The Paris exponent, n, was estimated for the different R values and found to be very high compared to homogeneous materials. The work was completed with microstructural and fractographic investigation by scanning electron microscope (SEM).
- 12 January 2010
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 636-637, 1490-1495
Fracture Behaviour of Brazed Soft Martensitic Stainless Steel Joints under Cyclic Loading
The fracture behaviour of brazed joints of the soft martensitic stainless steel X3CrNiMo13-4 under cyclic loading is investigated. The fatigue crack propagation curves (da/dN-ΔK) were derived for different load ratios R. The fatigue crack threshold values ΔKth were estimated to be 9 MPa m0.5, 7 MPa m0.5, 6 MPa m0.5 and 4 MPa m0.5 for the R values of 0.1, 0.3, 0.5 and 0.7, respectively. In addition, crack growth curves were derived for different constant loads ΔF. The Paris exponent, n, was estimated for the different R values and found to be very high compared to homogeneous materials. The work was completed with microstructural and fractographic investigation by scanning electron microscope (SEM).
- 21 November 2006
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 30 (3) , 206-213
A fracture mechanics approach to estimate the fatigue endurance of welded t‐joints including residual stress effects
Residual stresses and weld defects play a major role in the fatigue behaviour of welded structures, so these effects need to be accounted for in a theoretical analysis. A simplified engineering procedure based on linear‐elastic fracture mechanics is applied to estimate the fatigue behaviour, particularly the limit of endurance. Local geometrical irregularities and pre‐existing flaws, which are typical for this kind of weld, are covered by an overall notch intensity factor instead of a specific stress intensity factor, so the initial flaw size is not needed explicitly in the analysis. The effect of residual stresses can be easily included. The cut‐compliance method was applied to measure the residual stress distribution on the cross‐section of the weld. A welded T‐joint was used as a benchmark. Unexpectedly, compressive residual stresses were found to prevail in the root region. According to the analysis, they contribute to the endurance limit of the considered joint by about 50%. This result was confirmed by fatigue tests where a significant decrease in the fatigue strength after a post‐weld stress relieving heat treatment was observed.
- 21 November 2006
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 30 (3) , 206-213
A fracture mechanics approach to estimate the fatigue endurance of welded t‐joints including residual stress effects
Residual stresses and weld defects play a major role in the fatigue behaviour of welded structures, so these effects need to be accounted for in a theoretical analysis. A simplified engineering procedure based on linear‐elastic fracture mechanics is applied to estimate the fatigue behaviour, particularly the limit of endurance. Local geometrical irregularities and pre‐existing flaws, which are typical for this kind of weld, are covered by an overall notch intensity factor instead of a specific stress intensity factor, so the initial flaw size is not needed explicitly in the analysis. The effect of residual stresses can be easily included. The cut‐compliance method was applied to measure the residual stress distribution on the cross‐section of the weld. A welded T‐joint was used as a benchmark. Unexpectedly, compressive residual stresses were found to prevail in the root region. According to the analysis, they contribute to the endurance limit of the considered joint by about 50%. This result was confirmed by fatigue tests where a significant decrease in the fatigue strength after a post‐weld stress relieving heat treatment was observed.
- 7 August 2002
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 404-407, 515-520
Near-Surface Stress Measurement in 2D and 3D by the Cut Compliance Technique
The cut-compliance (CC-) method can be applied in a semi-destructive way by introducing only a shallow slot instead of a cut through the thickness. This requires the influence function to account for the U-shape of the shallow slot and the 3D-effects that affect the stress relaxation. In the present paper a simplified way to evaluate surface stresses from a slot is presented and discussed. By examples it is shown that a two-parameter approximation is often sufficient to characterize the near surface residual stresses in a narrow range of depth. Beyond this range, the procedure described herein can be matched with the common procedure of the CC-method. The analysis is explained first for the simpler case of a 2D-structure. Then the generalization to a 3D-case is shown and discussed. For both cases illustrative examples of measurements are given.
- 7 August 2002
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 404-407, 515-520
Near-Surface Stress Measurement in 2D and 3D by the Cut Compliance Technique
The cut-compliance (CC-) method can be applied in a semi-destructive way by introducing only a shallow slot instead of a cut through the thickness. This requires the influence function to account for the U-shape of the shallow slot and the 3D-effects that affect the stress relaxation. In the present paper a simplified way to evaluate surface stresses from a slot is presented and discussed. By examples it is shown that a two-parameter approximation is often sufficient to characterize the near surface residual stresses in a narrow range of depth. Beyond this range, the procedure described herein can be matched with the common procedure of the CC-method. The analysis is explained first for the simpler case of a 2D-structure. Then the generalization to a 3D-case is shown and discussed. For both cases illustrative examples of measurements are given.
- 1 January 2002
- Published by Springer Nature
- p. 213-224
Relation of Fracture Energy of Sub-Sized Charpy Specimens to Standard Charpy Energy and Fracture Toughness
- 1 January 2002
- Published by Springer Nature
- p. 213-224
Relation of Fracture Energy of Sub-Sized Charpy Specimens to Standard Charpy Energy and Fracture Toughness
- 21 May 2000
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 347-349, 150-155
Residual Stress Measurement in Cracked Components: Capabilities and Limitations of the Cut Compliance Method
- 21 May 2000
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 347-349, 150-155
Residual Stress Measurement in Cracked Components: Capabilities and Limitations of the Cut Compliance Method