ASAlfred B. O. Soboyejo

Alfred B. O. Soboyejo

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alfred B. O. Soboyejo has a total of 17 co-authors. Here are the top co-authors by number of shared publications:

  • Amadou Hama Maiga

    International Institute for Water and Environmental Engineering

    1 shared publication
  • Anand Plappally

    Assistant Professor, Indian Institute of Technology Jodhpur (IITJ), Rajasthan 342011, India; formerly Graduate Student, Dept. of Food, Agricultural and Biological Engineering, Ohio State Univ., 590 Woody Hayes Dr., Columbus, OH 43210

    1 shared publication
  • Ebenezer Annan

    Ph.D. Candidate, Dept. of Materials Science and Engineering, African Univ. of Science and Technology (AUST), Km 10 Airport Rd., P.M.B 681, Garki, Abuja, Federal Capital Territory, Nigeria; and Assistant Lecturer, Univ. of Ghana, Accra, Ghana

    1 shared publication
  • Francis Nyongesa

    Senior Lecturer, Dept. of Physics, Univ. of Nairobi, P.O. Box 30197-00100, Nairobi, Kenya

    1 shared publication
  • Ismaiel Yakub

    Lecturer, Dept. of Mechanical and Aerospace Engineering and the Keller Center for Innovation in Engineering Education, Princeton Univ., Princeton, NJ 08544

    1 shared publication
  • Kabiru Mustapha

    Ph.D. Candidate, Dept. of Materials Science and Engineering, African Univ. of Science and Technology (AUST), Km 10 Airport Rd., P.M.B 681, Garki, Abuja, Federal Capital Territory, Nigeria; and Assistant Lecturer, Dept. of Materials Science and Engineering, Kwara State Univ., Ilorin, Nigeria

    1 shared publication

Latest Publications

  • Statistical Distributions of the Strength and Fracture Toughness of Recycled Polyethylene-Reinforced Laterite Composites

    by Salifu T. Azeko, Kabiru Mustapha, Ebenezer Annan, Olushola S. Odusanya, Alfred B. O. Soboyejo, Winston O. Soboyejo

    This paper presents the results of combined experimental and theoretical studies of the statistical distributions of the strength and fracture toughness of recycled polyethylene-reinforced laterite composites for potential applications in building materials. The composites are produced with different volume percentages (0–30% v/v) and particle sizes (∼300±0.02, ∼600 ± 0.03, ∼900 ± 0.03, ∼1,200±0.02, ∼1,500±0.04, and 1,800±0.03 μm) of powdered polyethylene (PE) in a laterite matrix. The composites with ∼900±0.03 μm and 20-volume percentage of PE are shown to have the best combination of flexural-compressive strengths and fracture toughness. The statistical variations in the flexural-compressive strengths and fracture toughness are well characterized by the Weibull distributions.


  • Porosity, Flow, and Filtration Characteristics of Frustum-Shaped Ceramic Water Filters

    by Ismaiel Yakub, Anand Plappally, Megan Leftwich, Karen Malatesta, Katie C. Friedman, Sam Obwoya, Francis Nyongesa, Amadou H. Maiga, Alfred B. O. Soboyejo, Stefanos Logothetis, et al.

    This paper presents the results of an experimental study of the effects of porosity on the flow rate and Escherichia coli (E. coli) filtration characteristics of porous ceramic water filters (CWFs) prepared without a coating of silver. Clay-based CWFs were fabricated by sintering composites of redart clay and fine woodchips (sawdust) in three different proportions by volume, viz: 50∶50 , 65∶35 , and 75∶25 . Sintering the greenware below 1,000°C produced reddish colored pot of three different degrees of porosity and micro- and nanoscale pores, which are the key to efficient filtration. The porosities and pore size distribution frequencies of the sintered clay ceramics were characterized using mercury intrusion porosimetry (MIP). The porosity of the CWFs ranged from ∼36% to ∼47% and increased with increasing sawdust content in a linear fashion, and the pore size varied from ∼10  nm to ∼100  μm . The volume flow rates of water through the CWFs were investigated by measuring the cumulative amount of water flow as a function of time. The flow rate was found to increase with increasing porosity of the CWFs. The effective intrinsic permeabilities of the CWFs were then obtained from Darcy fits to the flow rate data. These were compared with values obtained using the Katz-Thompson method. Both approaches gave comparable results of permeability between ∼1  millidarcy to ∼50  millidarcy . The tortuosity of the CWFs was found from Hager’s equation to range from ∼10 to ∼60 . In general, while the permeability of the CWFs decreased with increasing clay content, tortuosity increased with increasing clay content. The CWFs removed E. coli from aqueous suspension very efficiently with average log reduction values between 5.7–6.4. The implications and limitations of the results are discussed for the effective filtration of water in the developing world.


  • Understanding a Contractor’s Regional Variations in Safety Performance

    by Qian Chen, Ruoyu Jin, Alfred Soboyejo

    Contractors’ safety performance can vary widely in the construction industry. However, it has not been well recognized that variations in safety performance could exist in the same contractor’s regional offices. There is also a lack of understanding of the differences between regions and what causes these variations. This paper analyzes the safety performance of a general contractor’s six major regional branches across four states after implementation of a new safety management program. The research finds apparent differences in regional incident rates (IRs) and safety violation rates (SVRs), although the shared perceptions from workers and site management personnel about how the safety program is implemented (i.e., safety climate and culture) are generally consistent companywide. This research also discloses that regional IRs, SVRs, safety climate, and culture are uncorrelated in the long term (during the 17-month study period), but have some linear relationships over a short duration (during the 4-month survey period). The correlation analysis in this study does not find a significant influence of workers’ demographic characteristics and a few other potential influencing factors on regional safety performance. These findings will provide useful insights to industry practitioners who aim to achieve good, consistent safety management and performance across regions.