Hiroyuki Yomo

Optimized resource allocation of the Downlink (DL) in wireless systems utilizing Multi-Carrier (MC) transmission requires Channel State Information (CSI) feedback for each user/subchannel to the Base Station (BS), consuming a high amount of Uplink (UL) radio resources. To alleviate this problem, several works have considered contention-based CSI feedback in the UL control channel. We propose such a feedback scheme for a generic MC system, based on the idea of variable collision protection, where the probability that a feedback information experiences a collision depends on its importance. By partitioning the CSI into orthogonal layers of priority, and allocating different numbers of feedback slots to each layer, this scheme ensures that the feedback success probability is higher for the CSI with better quality, which is more likely to be used by the scheduler. Furthermore, we present a theoretical performance analysis of the proposed scheme, assuming Maximum CSI (Max CSI) and normalized Proportional Fair Scheduler (PFS), where a tight approximation of the achievable throughput is obtained assuming discrete Adaptive Modulation (AM) and CSI feedback which are relevant for the practical systems. Analytical and simulation results show that our proposed scheme provides an excellent trade-off between system performance and feedback overhead.

It has recently been recognized that the wireless networks represent a fertile ground for devising communication modes based on network coding. A particularly suitable application of the network coding arises for the two--way relay channels, where two nodes communicate with each other assisted by using a third, relay node. Such a scenario enables application of \emph{physical network coding}, where the network coding is either done (a) jointly with the channel coding or (b) through physical combining of the communication flows over the multiple access channel. In this paper we first group the existing schemes for physical network coding into two generic schemes, termed 3--step and 2--step scheme, respectively. We investigate the conditions for maximization of the two--way rate for each individual scheme: (1) the Decode--and--Forward (DF) 3--step schemes (2) three different schemes with two steps: Amplify--and--Forward (AF), JDF and Denoise--and--Forward (DNF). While the DNF scheme has a potential to offer the best two--way rate, the most interesting result of the paper is that, for some SNR configurations of the source--relay links, JDF yields identical maximal two--way rate as the upper bound on the rate for DNF.

We address the problem of channel state information (CSI) feedback for scheduling the downlink (DL) data transmissions in a cellular system based on orthogonal frequency division multiple access (OFDMA). In order to benefit from multi-user diversity, the scheduler needs to know each user's CSI for each subchannel and time frame. However, this feedback information can become very high when the number of subchannels and/or users increase. Therefore, we have designed an adaptive feedback encoding method which can optimize the amount of feedback according to the variable amount of CSI requested by the base station (BS). The amount of useful CSI depends not only on the number of users, but also on the scheduling made at the BS. The simulation results show that with our adaptive encoding scheme, the performance of maximum CSI and proportional fair scheduling (PFS) with full CSI can be approached with a considerably reduced amount of feedback

This paper proposes a power control method for a hybrid duplexing scheme which has both time division duplex (TDD) and frequency division duplex (FDD) components. In the proposed method, the base station (BS) adaptively and continuously changes the transmission power for a mobile station (MS) whose transmission parameters have been scheduled by exploiting channel state information (CSI) obtained through channel reciprocity. The TDD component in hybrid duplexing makes it possible for the BS to exploit the channel reciprocity and the FDD component enables fast feed-back from MS to BS. By using the proposed power control method, the BS can quickly change the transmission power for a MS during a down-link (DL) frame. This counteracts the change in link condition due to MS mobility and/or burst interference (i.e. channel non-reciprocity problem). This allows the scheduling of BS made in the beginning of DL frame to be valid for the whole DL frame since the MS can experience almost constant link quality during a DL frame. Our simulation results show that the proposed power control method can significantly improve bit error rate (BER) performance

In this paper, we propose a hybrid forwarding scheme for cooperative relaying in orthogonal frequency division multiplexing (OFDM) based networks. The proposed hybrid forwarding scheme changes the type of the forwarding scheme used by a relay terminal on a per sub-carrier basis. It adaptively decides to use either "Amplify and Forward (AF)" or "Decode and Forward (DF)" or "no relay" according to the instantaneous Signal to Noise Ratio (SNR) conditions between the source, relay and destination terminals. This decision is made based on analytically derived equations, which makes it possible to take into account all the link conditions in a relay network with low computational complexity. The bit error performance is presented for cooperative receive diversity with AF, with DF, with proposed hybrid forwarding scheme and for noncooperative transmission. Our results show that the proposed hybrid forwarding scheme significantly outperforms conventional cooperative relaying with AF and DF, and direct transmission schemes.

This paper considers relaying techniques that increase the achievable throughput in multi-hop wireless networks by taking advantage of the bi-directional traffic flow. Such a relaying technique is termed relaying with Bi-directional Amplification of Throughput (BAT-relaying). The BAT-relaying is utilizing the concept of anti-packets, defined for bi-directional traffic flows. The relay node combines the anti-packets that are destined for different nodes and broadcasts the combined packet. Two BAT-relaying techniques have been proposed previously, Decode-and-Forward (DF) BAT-relaying and Amplify-and-Forward (AF) BAT-relaying. While in DF the relay node combines the packets by an XOR operation, AF BAT-relaying utilizes the inherent packet combining provided by the multiple access channel. In an errorless channel, AF has always higher achievable throughput than DF, but in noisy channels the noise amplification can severely degrade the performance of AF. In this paper we introduce a new scheme for BAT-relaying, termed Denoise-And-Forward (DNF) BAT-Relaying. The DNF BAT-relaying also makes use of the combining provided by the multiple access channel, but it removes the noise from the combined anti-packets before broadcasting to the destinations. While in the noiseless channel DNF and AF offer the same throughput performance which is superior to DF BAT-relaying, in large regions of the lower SNR values DNF BAT-relaying has the best throughput performance of all three schemes. Due to the unconventional nature of the BAT-relaying schemes, there are many open issues for further investigation. The design of a practical DNF scheme concerns several protocol layers, including modulation and coding.

This paper presents an overview of physical (PHY) and medium access control (MAC) layers for IEEE 802.11a, which is a standard of a broadband high-speed wireless local area network (WLAN). IEEE 802.11a uses 5 GHz frequency band and its PHY is based on orthogonal frequency division multiplexing (OFDM). In this paper, we evaluate the OFDM-based PHY and MAC performance of IEEE 802.11a under various practical wideband channel models, which are abstracted from actual propagation measurements. The effects of different transmission modes defined in PHY on the IEEE 802.11 system performance are investigated. We also discuss the impact of link adaptation, which attempts to choose the best-suited transmission mode according to channel conditions, on the overall system performance.