Brent Nelson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Brent Nelson has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Brad Hutchings
2 shared publicationsMichael Wirthlin
Dept. of Electrical and Computer Engineering, NSF Center for High-Performance Reconfigurable Computing (CHREC), Brigham Young University, Provo, UT, USA
2 shared publicationsAnthony L. Slade
1 shared publicationBrad L. Hutchings
1 shared publication- Brad L. Hutchings
Brigham Young University
1 shared publication Doran Wilde
1 shared publication
Latest Publications
- 13 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 57 (6) , 3506-3514
Synchronization Techniques for Crossing Multiple Clock Domains in FPGA-Based TMR Circuits
Triple modular redundancy (TMR) is a widely used mitigation technique to protect FPGA circuits against single event upsets (SEUs). TMR, however, does not adequately protect signals that cross asynchronous clock domains. Signals which cross clock domains in TMR circuits may suffer from the combined effects of two failure modes: asynchronous sampling effects and SEUs. This paper analyzes and quantifies these problems. In addition, various solutions are proposed for designing safe synchronizers with TMR. Finally, the improvements in reliability provided by the proposed synchronizers are demonstrated by both mathematical modeling and fault injection testing on an FPGA circuit. It is shown that the proposed mitigated synchronizer designs provide between 6 and 10 orders of magnitude improvement in reliability compared to unmitigated designs.
- 13 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 57 (6) , 3506-3514
Synchronization Techniques for Crossing Multiple Clock Domains in FPGA-Based TMR Circuits
Triple modular redundancy (TMR) is a widely used mitigation technique to protect FPGA circuits against single event upsets (SEUs). TMR, however, does not adequately protect signals that cross asynchronous clock domains. Signals which cross clock domains in TMR circuits may suffer from the combined effects of two failure modes: asynchronous sampling effects and SEUs. This paper analyzes and quantifies these problems. In addition, various solutions are proposed for designing safe synchronizers with TMR. Finally, the improvements in reliability provided by the proposed synchronizers are demonstrated by both mathematical modeling and fault injection testing on an FPGA circuit. It is shown that the proposed mitigated synchronizer designs provide between 6 and 10 orders of magnitude improvement in reliability compared to unmitigated designs.
- Open Access
- 1 July 2008
- Published by Defense Technical Information Center (DTIC)
Future Field Programmable Gate Array (FPGA) Design Methodologies and Tool Flows
Interest is growing in the use of FPGA devices for high-performance, efficient parallel computation. The large amount of programmable logic, internal routing, and memory can be used to perform a wide variety of high-performance computation more efficiently than traditional microprocessor-based computing architectures. The productivity of FPGA design, however, is very low. FPGA design is very time consuming and requires low-level hardware design skills. This study investigated this FPGA design productivity problem and identified potential solutions that will provide revolutionary improvements in design productivity. Three research areas that must be addressed to achieve such improvements are significant improvement in reuse of FPGA circuits, identification and deployment of higher level design abstractions, and increasing the number of turns per day to significantly increase the number of design iterations. The results of this study suggest that with adequate advancement in each of these areas, FPGA design productivity can be increased by 25X over current practice.
- 1 July 2008
- Published by Defense Technical Information Center (DTIC)
Open AccessFuture Field Programmable Gate Array (FPGA) Design Methodologies and Tool Flows
Interest is growing in the use of FPGA devices for high-performance, efficient parallel computation. The large amount of programmable logic, internal routing, and memory can be used to perform a wide variety of high-performance computation more efficiently than traditional microprocessor-based computing architectures. The productivity of FPGA design, however, is very low. FPGA design is very time consuming and requires low-level hardware design skills. This study investigated this FPGA design productivity problem and identified potential solutions that will provide revolutionary improvements in design productivity. Three research areas that must be addressed to achieve such improvements are significant improvement in reuse of FPGA circuits, identification and deployment of higher level design abstractions, and increasing the number of turns per day to significantly increase the number of design iterations. The results of this study suggest that with adequate advancement in each of these areas, FPGA design productivity can be increased by 25X over current practice.
- 29 April 2008
- Published by Springer Nature in Journal of Signal Processing Systems
- Vol. 53 (1) , 187-196
Design, Debug, Deploy: The Creation of Configurable Computing Applications
- 29 April 2008
- Published by Springer Nature in Journal of Signal Processing Systems
- Vol. 53 (1) , 187-196
Design, Debug, Deploy: The Creation of Configurable Computing Applications
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10586393,p. 2036-2040
The Design of an FPGA-Based MIMO Receiver: Algorithmic and Architectural Interactions
A research team at Brigham Young University is currently developing a high-performance, FPGA-based demodulator for detecting a space-time coded signal. The project timeline required that the algorithm be concurrently developed, to a certain extent, with the hardware implementation. Thus, from the outset both algorithm and hardware implementation researchers worked closely together in contrast to the, all too common, three-step development approach (algorithm development, throw-algorithm-over-wall, hardware implementation). In this paper we outline the unique characteristics of the system and then discuss the interaction between algorithm design and architectural implementation. In particular, we focus on two blocks from the system: the carrier frequency offset estimation block and the pilot detector block and show their evolution from their original mathematical formulations to equivalent but greatly simplified hardware implementations.
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10586393,p. 2036-2040
The Design of an FPGA-Based MIMO Receiver: Algorithmic and Architectural Interactions
A research team at Brigham Young University is currently developing a high-performance, FPGA-based demodulator for detecting a space-time coded signal. The project timeline required that the algorithm be concurrently developed, to a certain extent, with the hardware implementation. Thus, from the outset both algorithm and hardware implementation researchers worked closely together in contrast to the, all too common, three-step development approach (algorithm development, throw-algorithm-over-wall, hardware implementation). In this paper we outline the unique characteristics of the system and then discuss the interaction between algorithm design and architectural implementation. In particular, we focus on two blocks from the system: the carrier frequency offset estimation block and the pilot detector block and show their evolution from their original mathematical formulations to equivalent but greatly simplified hardware implementations.
- 1 September 2003
- Published by Defense Technical Information Center (DTIC)
Unified Debug Environment for Adaptive Computing Systems
Adaptive computing systems (ACS) are hardware systems based around FPGA technology. Historically, design and debug tools for such systems have been based on ASIC technology. However, FPGA technology provides features which suggest different approaches be used for debug. For example, readback is a feature available in many FPGA devices which provides the ability to query an executing FPGA device for its entire internal state, providing unprecedented visibility into the executing design. The central element of the debug environment developed in this work is a debug services module (DSM). It provides a unified simulation/hardware execution debug environment which allows the user to debug the executing hardware in the context of the original design environment. This means signal values in the executing hardware can be viewed and manipulated using their original signal names from the design source. In addition, the DSM provides the following support for designs running on ACS platforms: checkpointing, multitasking, remote access, and interfacing with external high-level design tools. Finally, the DSM provides support for the automatic synthesis of debug circuitry to enable rapid instrumentation of FPGA designs for debug purposes. This report summarizes the debug system and a number of the experiments completed using it.
- 1 September 2003
- Published by Defense Technical Information Center (DTIC)
Unified Debug Environment for Adaptive Computing Systems
Adaptive computing systems (ACS) are hardware systems based around FPGA technology. Historically, design and debug tools for such systems have been based on ASIC technology. However, FPGA technology provides features which suggest different approaches be used for debug. For example, readback is a feature available in many FPGA devices which provides the ability to query an executing FPGA device for its entire internal state, providing unprecedented visibility into the executing design. The central element of the debug environment developed in this work is a debug services module (DSM). It provides a unified simulation/hardware execution debug environment which allows the user to debug the executing hardware in the context of the original design environment. This means signal values in the executing hardware can be viewed and manipulated using their original signal names from the design source. In addition, the DSM provides the following support for designs running on ACS platforms: checkpointing, multitasking, remote access, and interfacing with external high-level design tools. Finally, the DSM provides support for the automatic synthesis of debug circuitry to enable rapid instrumentation of FPGA designs for debug purposes. This report summarizes the debug system and a number of the experiments completed using it.
- 1 January 2003
- Published by Defense Technical Information Center (DTIC)
Reconfigurable Computing Application Frameworks
FPGA-based Configurable Computing Machines (CCMs) offer powerful and flexible general-purpose computing platforms. However, development for FPGA-based designs using modern CAD tools is geared mainly toward an ASIC-like process. This is inadequate for the needs of CCM application development. This paper discusses an application framework for developing CCM-based applications beyond just the hardware configuration. This framework leverages the advantages of CCMs (availability, programmability, visibility, and controllability) to help create CCM-based applications throughout the entire development process (i.e. design, debug, and deploy). The framework itself is deployed with the final application, thus permitting dynamic circuit configurations that include data folding optimizations based on user input. The resulting system aids in creating applications that are potentially more intuitive, easier to develop, and better performing. An example application demonstrates the use of the application framework and the potential benefits.
- 1 January 2003
- Published by Defense Technical Information Center (DTIC)
Reconfigurable Computing Application Frameworks
FPGA-based Configurable Computing Machines (CCMs) offer powerful and flexible general-purpose computing platforms. However, development for FPGA-based designs using modern CAD tools is geared mainly toward an ASIC-like process. This is inadequate for the needs of CCM application development. This paper discusses an application framework for developing CCM-based applications beyond just the hardware configuration. This framework leverages the advantages of CCMs (availability, programmability, visibility, and controllability) to help create CCM-based applications throughout the entire development process (i.e. design, debug, and deploy). The framework itself is deployed with the final application, thus permitting dynamic circuit configurations that include data folding optimizations based on user input. The resulting system aids in creating applications that are potentially more intuitive, easier to develop, and better performing. An example application demonstrates the use of the application framework and the potential benefits.