Hideo Cho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hideo Cho has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Hiroaki Ito
Kindai University
5 shared publicationsTakuma Matsuo
Department of Mechanical Engineering, Meiji University
5 shared publicationsKojiro Nishimiya
青山学院大学 理工学
3 shared publications- Kanji Ono
Department of Materials Science and Engineering, University of California, Los Angeles (UCLA), Los Angeles, CA 90095, USA
2 shared publications Mikio Takemoto
Aoyama Gakuin University
2 shared publications- Stanislav I. Rokhlin
The Ohio State University, Department of Materials Science and Engineering, Edison Joining Technology Center, 1248 Arthur E. Adams Dr., Columbus, OH 43221, United States
2 shared publications
Latest Publications
- Open Access
- 1 January 2023
- Published by The Visualization Society of Japan in Journal of the Visualization Society of Japan
- Vol. 43 (167) , 20-23
パルス光弾性法を用いたZGVラム波の可視化と接着性状評価
高分子接着剤による接着部の評価を行うことを目的とした光弾性法を用いたZero-group-velocity(ZGV)ラム波の伝搬挙動の可視化を行った.ZGVラム波は,群速度が0であるが有限の位相速度を有する波動で高い空間分解能で伝搬媒体の弾性的な性質を評価できる手法であり,接着性状を評価できる可能性がある波動である.しかし,現在では接着性とZGVラム波の伝搬挙動のとの関係は不明な点が多い.光弾性法によってZGVラム波を可視化したところ,ZGVラム波と接着性状の関係を直感的に理解するのに役立つと期待できる.良好な接着性状の場合,ZGVラム波は両方の被着材で同一の振動モードを示したが,接着状態が不良な場合は異なる振動モードとなった.今後は可視化結果に基づいて接着面での境界条件を明らかにしる予定である.
- 1 January 2023
- Published by The Visualization Society of Japan in Journal of the Visualization Society of Japan
- Vol. 43 (167) , 20-23
Open Accessパルス光弾性法を用いたZGVラム波の可視化と接着性状評価
高分子接着剤による接着部の評価を行うことを目的とした光弾性法を用いたZero-group-velocity(ZGV)ラム波の伝搬挙動の可視化を行った.ZGVラム波は,群速度が0であるが有限の位相速度を有する波動で高い空間分解能で伝搬媒体の弾性的な性質を評価できる手法であり,接着性状を評価できる可能性がある波動である.しかし,現在では接着性とZGVラム波の伝搬挙動のとの関係は不明な点が多い.光弾性法によってZGVラム波を可視化したところ,ZGVラム波と接着性状の関係を直感的に理解するのに役立つと期待できる.良好な接着性状の場合,ZGVラム波は両方の被着材で同一の振動モードを示したが,接着状態が不良な場合は異なる振動モードとなった.今後は可視化結果に基づいて接着面での境界条件を明らかにしる予定である.
- Open Access
Transmission Sensitivities of Contact Ultrasonic Transducers and Their Applications
In all ultrasonic material evaluation methods, transducers and sensors play a key role of mechanoelectrical conversion. Their transduction characteristics must be known quantitatively in designing and implementing successful structural health monitoring (SHM) systems. Yet, their calibration and verification have lagged behind most other aspects of SHM system development. This study aims to extend recent advances in quantifying the transmission and receiving sensitivities to normally incident longitudinal waves of ultrasonic transducers and acoustic emission sensors. This paper covers extending the range of detection to lower frequencies, expanding to areal and multiple sensing methods and examining transducer loading effects. Using the refined transmission characteristics, the receiving sensitivities of transducers and sensors were reexamined under the conditions representing their actual usage. Results confirm that the interfacial wave transmission is governed by wave propagation theory and that the receiving sensitivity of resonant acoustic emission sensors peaks at antiresonance.
Open AccessTransmission Sensitivities of Contact Ultrasonic Transducers and Their Applications
In all ultrasonic material evaluation methods, transducers and sensors play a key role of mechanoelectrical conversion. Their transduction characteristics must be known quantitatively in designing and implementing successful structural health monitoring (SHM) systems. Yet, their calibration and verification have lagged behind most other aspects of SHM system development. This study aims to extend recent advances in quantifying the transmission and receiving sensitivities to normally incident longitudinal waves of ultrasonic transducers and acoustic emission sensors. This paper covers extending the range of detection to lower frequencies, expanding to areal and multiple sensing methods and examining transducer loading effects. Using the refined transmission characteristics, the receiving sensitivities of transducers and sensors were reexamined under the conditions representing their actual usage. Results confirm that the interfacial wave transmission is governed by wave propagation theory and that the receiving sensitivity of resonant acoustic emission sensors peaks at antiresonance.
- 24 October 2018
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 37 (4) , 83
Acoustic Emission Generation Behavior in A7075-T651 and A6061-T6 Aluminum Alloys With and Without Cathodic Hydrogen Charging Under Cyclic Loading
- 24 October 2018
- Published by Springer Nature in Journal of Nondestructive Evaluation
- Vol. 37 (4) , 83
Acoustic Emission Generation Behavior in A7075-T651 and A6061-T6 Aluminum Alloys With and Without Cathodic Hydrogen Charging Under Cyclic Loading
- 1 January 2018
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 5 (2) , 17-00568
Characterization of contact condition in a flange connection by longitudinal waves
The integrity of flange joints is critical in all pipe systems. To test this integrity, an ultrasonic method characterizing the condition of the flange joint would be a vital tool. In this study, we analyzed the contact conditions on a metal/gasket/metal connection. The instantaneous frequency profile, i.e., the phase change of the wave with time for longitudinal waves transmitted in an Al alloy/gasket/Al alloy system, was evaluated under various contact pressures. The instantaneous frequency (IF) was calculated with a complex continuous wavelet transform with a modified Morlet function as a mother wavelet. The maximum IF of the waves monotonically increased with contact pressure, showing similar properties as the amplitude of the waves. A one-dimensional numerical calculation with a finite difference time domain method with a spring condition for expressing various contact conditions or contact stiffness revealed that a large phase delay of the transmission wave was generated at a low contact stiffness interface, and the amount of delay was correlated with the contact stiffness. On the other hand, the delay in the reflected wave was very small.
- 1 January 2018
- Published by Japan Society of Mechanical Engineers in Mechanical Engineering Journal
- Vol. 5 (2) , 17-00568
Characterization of contact condition in a flange connection by longitudinal waves
The integrity of flange joints is critical in all pipe systems. To test this integrity, an ultrasonic method characterizing the condition of the flange joint would be a vital tool. In this study, we analyzed the contact conditions on a metal/gasket/metal connection. The instantaneous frequency profile, i.e., the phase change of the wave with time for longitudinal waves transmitted in an Al alloy/gasket/Al alloy system, was evaluated under various contact pressures. The instantaneous frequency (IF) was calculated with a complex continuous wavelet transform with a modified Morlet function as a mother wavelet. The maximum IF of the waves monotonically increased with contact pressure, showing similar properties as the amplitude of the waves. A one-dimensional numerical calculation with a finite difference time domain method with a spring condition for expressing various contact conditions or contact stiffness revealed that a large phase delay of the transmission wave was generated at a low contact stiffness interface, and the amount of delay was correlated with the contact stiffness. On the other hand, the delay in the reflected wave was very small.
- Open Access
- 21 September 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (10) , 964
Bar-Wave Calibration of Acoustic Emission Sensors
This study extended a bar-wave calibration method for acoustic emission (AE) sensors. It combined laser interferometer displacement measurements and the wave propagation medium of a long bar, excited at its end with an ultrasonic transducer driven by a pulser. Receiving bar-wave sensitivities of 16 types of AE sensors were measured and compared to their receiving sensitivities to normally incident waves. The two types of the receiving sensitivity always differed for a given AE sensor. The bar-wave sensitivities of R6a sensors resembled their surface-wave sensitivities, indicating that the bar-wave sensitivities can represent the surface-wave sensitivities in typical AE applications. Some bar-wave modes were identified by comparing peaks found on observed Choi-Williams transform spectrograms with the positions on the dispersion curves for bar waves, calculated with the SAFE procedure. However, numerous bar-wave modes prevented exact identification, especially above 500 kHz. Aperture effects contributed to the sensitivity reduction at higher frequencies and to more fluctuating bar-wave receiving sensitivities even for sensors with smooth or flat receiving sensitivities to normally incident waves. Spectral dips observed in bar-wave results can be accounted for by aperture effect predictions reasonably well. For the selection of AE sensors, one needs to use the appropriate type of sensitivities considering waves to be detected.
- 21 September 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (10) , 964
Open AccessBar-Wave Calibration of Acoustic Emission Sensors
This study extended a bar-wave calibration method for acoustic emission (AE) sensors. It combined laser interferometer displacement measurements and the wave propagation medium of a long bar, excited at its end with an ultrasonic transducer driven by a pulser. Receiving bar-wave sensitivities of 16 types of AE sensors were measured and compared to their receiving sensitivities to normally incident waves. The two types of the receiving sensitivity always differed for a given AE sensor. The bar-wave sensitivities of R6a sensors resembled their surface-wave sensitivities, indicating that the bar-wave sensitivities can represent the surface-wave sensitivities in typical AE applications. Some bar-wave modes were identified by comparing peaks found on observed Choi-Williams transform spectrograms with the positions on the dispersion curves for bar waves, calculated with the SAFE procedure. However, numerous bar-wave modes prevented exact identification, especially above 500 kHz. Aperture effects contributed to the sensitivity reduction at higher frequencies and to more fluctuating bar-wave receiving sensitivities even for sensors with smooth or flat receiving sensitivities to normally incident waves. Spectral dips observed in bar-wave results can be accounted for by aperture effect predictions reasonably well. For the selection of AE sensors, one needs to use the appropriate type of sensitivities considering waves to be detected.
- Open Access
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2017, J0420106
Development of parabolic optical fiber sensor for detecting liquid-borne acoustic emission waves and its application to stress corrosion crack measurement
The goal of this study is to locate sources of liquid-borne AE waves with multi-channel system being comprised of multi parabolic optical fiber sensors. At first, different frequency characteristics of each parabolic type sensor in water is provided by the shape of the sensor holder around which the optical fiber was wound. These parabolic type sensors have a high directivity with half width at half amplitude of less than 20 degrees. A multi-channel system was realized by setting these sensors on one optical fiber. A signal from the system is composed of the two waveforms detected by each sensor and can be allowed to separate those two waveforms with wavelet transform of the signal. The arrival time difference of those two waves agreed well with the theoretical prediction which can be calculated by the distance difference of the sensor to the source and velocity of the wave (1500 m/s). Now, we have been trying to detect liquid-borne AE from SCC in a sensitized SUS304 in polythionic acid solution.
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2017, J0420106
Open AccessDevelopment of parabolic optical fiber sensor for detecting liquid-borne acoustic emission waves and its application to stress corrosion crack measurement
The goal of this study is to locate sources of liquid-borne AE waves with multi-channel system being comprised of multi parabolic optical fiber sensors. At first, different frequency characteristics of each parabolic type sensor in water is provided by the shape of the sensor holder around which the optical fiber was wound. These parabolic type sensors have a high directivity with half width at half amplitude of less than 20 degrees. A multi-channel system was realized by setting these sensors on one optical fiber. A signal from the system is composed of the two waveforms detected by each sensor and can be allowed to separate those two waveforms with wavelet transform of the signal. The arrival time difference of those two waves agreed well with the theoretical prediction which can be calculated by the distance difference of the sensor to the source and velocity of the wave (1500 m/s). Now, we have been trying to detect liquid-borne AE from SCC in a sensitized SUS304 in polythionic acid solution.
- Open Access
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2017, J0420203
AE measurement under the high temperature environment using a Sagnac interference type optical fiber sensor.
The Sagnac interference type optical fiber sensor using a feedback control for polarization of incident light to improve stability of the system was developed and utilized for AE measurement under the high temperature environment. Ni plated on a commercial Cu-coated optical fiber was wound around a carbon steel pipe and measured AE caused by the fracture of the oxide film on the pipe in 700°C. The total number of AE with an optical fiber sensor was 8110 events and was as many as the AE event with PZT type sensors set on low temperature portion. The AE sources were located on an oxide film fracture area observed by eye-inspection. A coiled sensor with an optical fiber was also developed by a sandwiching with metal plates for measuring AE on a plate structure. The coiled sensor can also detect AE from oxide film fracture at high temperature.
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2017, J0420203
Open AccessAE measurement under the high temperature environment using a Sagnac interference type optical fiber sensor.
The Sagnac interference type optical fiber sensor using a feedback control for polarization of incident light to improve stability of the system was developed and utilized for AE measurement under the high temperature environment. Ni plated on a commercial Cu-coated optical fiber was wound around a carbon steel pipe and measured AE caused by the fracture of the oxide film on the pipe in 700°C. The total number of AE with an optical fiber sensor was 8110 events and was as many as the AE event with PZT type sensors set on low temperature portion. The AE sources were located on an oxide film fracture area observed by eye-inspection. A coiled sensor with an optical fiber was also developed by a sandwiching with metal plates for measuring AE on a plate structure. The coiled sensor can also detect AE from oxide film fracture at high temperature.
- Open Access
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in Transactions of the JSME (in Japanese)
- Vol. 83 (852) , 17-00213
Evaluation of strength of DLC films at high temperature by static and cyclic indentation test with AE technique
This study aims to evaluate strength of a diamond-like carbon (DLC) film on a metal for glass press molding at high temperature. Static and cyclic indentation tests at high temperature up to 300℃ with AE monitoring technique were performed. AE monitoring reveled crack generation load or cyclic number during the indentation tests. The static strength of the films at each temperature was determined from maximum stress in the film in the radial direction induced by sink-in deformation due to static indentation. The maximum stress at each temperature was estimated with indentation loads at first AE generation and FEM analysis. Thermal stress in DLC film was at each temperature also calculated. The film strength estimated by taking the thermal stresses into account was decreased with an increase of temperature. In cyclic indentation test, AE due to cracks in film was detected after 1.0×104 cycles at the load where no crack generated under one loading cycle. The cyclic number to crack initiation for the sample in 300℃ was 1/50 smaller than that in room temperature.
- 1 January 2017
- Published by Japan Society of Mechanical Engineers in Transactions of the JSME (in Japanese)
- Vol. 83 (852) , 17-00213
Open AccessEvaluation of strength of DLC films at high temperature by static and cyclic indentation test with AE technique
This study aims to evaluate strength of a diamond-like carbon (DLC) film on a metal for glass press molding at high temperature. Static and cyclic indentation tests at high temperature up to 300℃ with AE monitoring technique were performed. AE monitoring reveled crack generation load or cyclic number during the indentation tests. The static strength of the films at each temperature was determined from maximum stress in the film in the radial direction induced by sink-in deformation due to static indentation. The maximum stress at each temperature was estimated with indentation loads at first AE generation and FEM analysis. Thermal stress in DLC film was at each temperature also calculated. The film strength estimated by taking the thermal stresses into account was decreased with an increase of temperature. In cyclic indentation test, AE due to cracks in film was detected after 1.0×104 cycles at the load where no crack generated under one loading cycle. The cyclic number to crack initiation for the sample in 300℃ was 1/50 smaller than that in room temperature.
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Materials and processing conference
- Vol. 2016.24, 331
Direct measurement of the waves propagation along the adhesive interface between glass plates and evaluation of adhesive quality by the waves
Curing and degraded process in epoxy agents between two glass plates have been tried to be monitored by the waves propagating through the bonding interface. The interface waves were directly measured with a Doppler interferometer with a laser probe transmitting through the glass plates. The two propagation modes of the interface waves were extracted by adding and subtracting the waves at upper and lower interfaces between the glass plates and the bonding layer. The group velocities and amplitude of the interface waves increased with curing and linearly decreased with degraded processes. Those changes would be corresponding to change in properties of adhesive agent.
- 1 January 2016
- Published by Japan Society of Mechanical Engineers in The Proceedings of the Materials and processing conference
- Vol. 2016.24, 331
Direct measurement of the waves propagation along the adhesive interface between glass plates and evaluation of adhesive quality by the waves
Curing and degraded process in epoxy agents between two glass plates have been tried to be monitored by the waves propagating through the bonding interface. The interface waves were directly measured with a Doppler interferometer with a laser probe transmitting through the glass plates. The two propagation modes of the interface waves were extracted by adding and subtracting the waves at upper and lower interfaces between the glass plates and the bonding layer. The group velocities and amplitude of the interface waves increased with curing and linearly decreased with degraded processes. Those changes would be corresponding to change in properties of adhesive agent.
- 1 September 2015
- Published by Elsevier in Ultrasonics
- Vol. 62, 213-222
Interface wave propagation and edge conversion at a low stiffness interphase layer between two solids: A numerical study
- 1 September 2015
- Published by Elsevier in Ultrasonics
- Vol. 62, 213-222
Interface wave propagation and edge conversion at a low stiffness interphase layer between two solids: A numerical study