Lamia Touiti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lamia Touiti has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Ehab Sabi1 shared publication
- Hyunwook Choo
Kyung Hee University, Department of Civil Engineering, 17104 Yongin, South Korea
1 shared publication Minhyuk Kwon
Department of Civil Engineering, Kyung Hee University, Yongin, 17104, South Korea
1 shared publicationTaesik Kim
School of Urban and Civil Engineering, Hongik University, Mapo-gu, Seoul, Republic of Korea
1 shared publicationWilliam Van Impe
ISSMGE, Ghent University Belgium
1 shared publicationYoung-Hoon Jung
Department of Civil Engineering, Kyung Hee University, Yongin, 17104, Republic of Korea
1 shared publication
Latest Publications
- Open Access
- 16 October 2020
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 11 (1) , 1-5
Creep of calcareous sand in Tunisia: effect of particle breakage at low stress level
Aims/hypothesis: One of the critical mechanisms determining creep in granular materials is the breakage of soil particles. This study aims at evaluating the time-dependent creep deformation of calcareous sand at low effective stress conditions. Methods: K0 creep tests were performed for both calcareous and silica sands at low stresses of 65 and 120 kPa, and the results of creep tests were compared with the results of constant rate of strain (CRS) tests at high stress levels up to 12 MPa. For a quantitative evaluation of the effect of the particle breakage on the creep deformation of calcareous sand, the relative breakage ( $$B_{r}$$ ) was determined based on the results of sieve analyses. Results: The results demonstrate that Tunisia calcareous sand experiences significant particle breakage during creep and the consequent creep deformation at low stress level. The determined $$B_{r}$$ after creep at low stress level is comparable with that after the CRS test at high stress level. Conclusions: High potential of particle breakage inherited by characteristic minerology of the calcareous Tunisia sand significantly influences the creep deformation at low stress level.- 16 October 2020
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 11 (1) , 1-5
Open AccessCreep of calcareous sand in Tunisia: effect of particle breakage at low stress level
Aims/hypothesis: One of the critical mechanisms determining creep in granular materials is the breakage of soil particles. This study aims at evaluating the time-dependent creep deformation of calcareous sand at low effective stress conditions. Methods: K0 creep tests were performed for both calcareous and silica sands at low stresses of 65 and 120 kPa, and the results of creep tests were compared with the results of constant rate of strain (CRS) tests at high stress levels up to 12 MPa. For a quantitative evaluation of the effect of the particle breakage on the creep deformation of calcareous sand, the relative breakage ( $$B_{r}$$ ) was determined based on the results of sieve analyses. Results: The results demonstrate that Tunisia calcareous sand experiences significant particle breakage during creep and the consequent creep deformation at low stress level. The determined $$B_{r}$$ after creep at low stress level is comparable with that after the CRS test at high stress level. Conclusions: High potential of particle breakage inherited by characteristic minerology of the calcareous Tunisia sand significantly influences the creep deformation at low stress level. - Open Access
- 8 October 2020
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 11 (1) , 1-14
Analysis of calcareous sand particle shape using fourier descriptor analysis
Soil particle shape analysis was conducted on two calcareous sands from Dissa and Matmata in Tunisia and one silica sand from Jumunjin in Korea using an image analysis method. This technique uses complex Fourier shape descriptors and image analysis of sand grains SEM photographs to provide accurate quantification of particle morphology and texture. The Fourier descriptors, denoted “Signature Descriptors”, provide measures of Elongation, Triangularity, Squareness, and Asymmetry and identify the overall shape of soil particles. A summary of higher-order descriptors provides textural information linked up to local roughness and texture characteristics. After analyzing the Fourier descriptors, elongation was found to be the major characteristics of the three sands, mainly for the Dissa and Matmata carbonate sands. In addition, the elongation signature descriptors for the Dissa and Matmata sands have very high values compared to those of Ras Alkhair (Saudi Arabia) and Dog’s bay (Ireland) sands. Therefore, the Dissa and Matmata carbonate sands have higher angles of friction and higher critical state angle of friction than Ras Alkhair and Dog’s bay sands. Furthermore, the Dissa and Matmata carbonate sands show higher roughness than Jumunjin’s silica sand.
- 8 October 2020
- Published by Springer Nature in International Journal of Geo-Engineering
- Vol. 11 (1) , 1-14
Open AccessAnalysis of calcareous sand particle shape using fourier descriptor analysis
Soil particle shape analysis was conducted on two calcareous sands from Dissa and Matmata in Tunisia and one silica sand from Jumunjin in Korea using an image analysis method. This technique uses complex Fourier shape descriptors and image analysis of sand grains SEM photographs to provide accurate quantification of particle morphology and texture. The Fourier descriptors, denoted “Signature Descriptors”, provide measures of Elongation, Triangularity, Squareness, and Asymmetry and identify the overall shape of soil particles. A summary of higher-order descriptors provides textural information linked up to local roughness and texture characteristics. After analyzing the Fourier descriptors, elongation was found to be the major characteristics of the three sands, mainly for the Dissa and Matmata carbonate sands. In addition, the elongation signature descriptors for the Dissa and Matmata sands have very high values compared to those of Ras Alkhair (Saudi Arabia) and Dog’s bay (Ireland) sands. Therefore, the Dissa and Matmata carbonate sands have higher angles of friction and higher critical state angle of friction than Ras Alkhair and Dog’s bay sands. Furthermore, the Dissa and Matmata carbonate sands show higher roughness than Jumunjin’s silica sand.
- 12 July 2017
- Published by Springer Nature
- p. 20-37
Considerations on the Stiffness of Sensitive Soft Soils
- 12 July 2017
- Published by Springer Nature
- p. 20-37
Considerations on the Stiffness of Sensitive Soft Soils